-
Product
Ensure Accurate Screening, Diagnosis & Monitoring
Ultrasound QA Solutions
-
Gammex is the only ultrasound QA solutions manufacturer with expertise in medical physics since 1969.The 156 phantom helped establish the mammography repeatability and reproducibility standard: any mammography technologist (radiographer) at any time, on any machine, can provide the same image set to help detect breast cancer.We collaborated with clinical and academic thought leaders to develop our patented HE Gel and the first portable Doppler Flow phantoms in the world. HE (High Equivalency) Gel is what sets Gammex ultrasound products apart; it helps ensure all your transducers and system settings are fully tested across the entire frequency range from 2 to 18 MHz. Our HE Gel combined with our medical physics and quality control expertise gives you confidence with consistent diagnostic image quality in clinical applications.
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-02
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
Passive Waveguide Components
-
We cover all kinds of connections between waveguide, coaxial, micro-strip and co-planar lines. Filters are available in waveguide technology as well as in stripline/micro-strip. Passive structures such as power splitter, power combiner, ortho-mode transducer and hybrids mostly are designed to meet the specific goals of the customer.
-
Product
RM-26999, 4-Channel Power Measurements Conditioner
786328-01
-
The RM-26999 is a rack-mounted, signal conditioning device that connects to several simultaneous-sampling multifunction I/O devices for power measurements. It features four voltage input channels with peak voltages up to 2,000 V and four … current transducer ports for current measurements. The current transducer ports are optimized for flux-gate transducers by providing all the power, communication, and signal lines required for accurate measurements.
-
Product
Displacement and Encoders
-
INCREMENTAL digital Transducers are mainly designed for displacement measurement in machine tools and other industrial applications. The sensors are characterized by high precision and are absolutely dust and waterproof. The used materials permit applications in heavy industrial environments.DISPLACEMENT Transducers are suitable for measurements of small distances up to 50mm. They are characterized by high accuracy and repeatability, reliability and fast response. Digital ENCODERS operate on optical or magnetical principal and are offered with incremental or absolute coded outputs. They are suitable for precision industrial applications.
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
Singlebeam Hydrographic Echosounders
-
Teledyne Marine Odom Hydrographic
Odom Hydrographic provides an extensive range of hydrographic level single beam echosounders with the flexibility of frequency agility supporting existing transducer installations. Models include modern PC screen based interfaces as well as support for tried and tested thermal record printing.
-
Product
Dynamometer
-
Dynamometers, force and torque transducers available in many models. Buy your dynamometer or force measurment products from Vetek!The difference between a load cell and a dynamometer is that the dynamometer is optimated for fast measurement.
-
Product
ReCalibration and Post Calibration Software
SI58
-
The SI58 software allows the user to set zero and span as well as do full temperature compensation and linearity corrections for your Validyne USB pressure transducer. The SI58 provides everything needed to change the range of your transducer and calibrate it through the new full scale pressure. Corrections to non-linearity and temperature error are also possible. The SI58 software provides prompts to the operator for temperature and pressure points to achieve an accurate calibration.
-
Product
Output Signal Cable
COSxx-A
-
The Output Signal Cable COSxx-A is specifically designed for use with SENIS H3A Magnetic Transducers, offering superior connectivity and reliability in your applications. This cable features the R605 connector, which is designed to accommodate differential signal output while ensuring a robust shield connection to minimize interference. With a meticulously crafted construction of Alpha Wire, it utilizes a configuration of two wires (20 x 2 x 0.12 mm²) surrounded by an effective shielding layer, making it ideal for precise signal transmission in various environments. In addition to its excellent technical specs, the cable is equipped with banana plugs for easy and secure connections. The VOUT- is designated with a red wire, while VOUT+ is represented by a yellow wire, and the shield is marked with a black wire. The connector's body integrates seamlessly with the cable shield, and the wires at the end are meticulously soldered to maintain performance integrity. This cable is tailored for engineers and technicians who require high-quality, reliable connections for their SENIS H3A transducers, ensuring optimal performance and longevity in critical applications.
-
Product
Flexible Current Sensor Probe
CTA
-
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
Product
Transducer For Rotation Angle
-
An industrial device that converts the physical angular position of a rotating shaft into a proportional, load-independent electrical output signal.
-
Product
Magnetic Transducers With Hybrid 1-/ 2-/ 3-Axis Hall Probe Sensors
H3B
-
The **H3B Magnetic Transducer** is an advanced Low Noise SENIS device designed for measuring magnetic fields through its hybrid three-axis Hall Probe. With a remarkable capacity for ultra-low noise, it effectively minimizes offset fluctuations, ensuring precision in magnetic field measurements. This robust transducer is tailored for applications that demand high accuracy and stability, integrating three high-resolution Hall sensors with an orthogonality error of less than 2°. Additionally, a built-in temperature sensor provides real-time temperature compensation, enhancing measurement reliability across various conditions.Beyond its noise reduction capabilities, the H3B transducer delivers a comprehensive output of three differential voltages corresponding to the magnetic flux density components (Bx, By, Bz) and a ground-referred voltage signaling the Hall sensor's local temperature. The system's innovative spinning-current technique significantly reduces low-frequency noise while maintaining excellent linearity, making it a valuable instrument for mapping magnetic fields, characterizing undulator systems, and performing quality control in laboratory and industrial settings.
-
Product
Digital Inclinometer
ZET 7054
-
ZET 7054 digital inclinometer is used in static systems to sustain platform position (biaxial mode). Low supply voltage, MODBUS protocol application – all this enables embedding of ZET 7054 inclinometer in almost any industrial system. The “Set zero position” function allows to set transducer to zero on each of the axes, and thus, to prevent the platform critical inclination along the coordinate specified.
-
Product
General Performance Pressure Transducers And Switches
-
These general performance Baratron® capacitance manometers are available as pressure transducers with an analog signal proportional to absolute or differential pressure, or as switches with relay outputs based on pressure.
-
Product
Variable Reluctance Absolute Pressure Sensor
AP10
-
The AP10, Absolute Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with carrier systems including the Validyne CD15 sine wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator to produce a high level analog DC output suitable for recording and control.
-
Product
Digital to LVDT-Digital to RVDT Converters
ITA
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices.
-
Product
Transducer Calibrator Systems
-
Unholtz-Dickie Transducer Calibration Systems have earned their place in industry as the standard for calibrating accelerometers and velocity transducers. The Model 680C is UD's latest generation of an automated transducer calibration system, utilizing the expanded features of the i5 based APEX SL-C Windows vibration control system.
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Advanced Ultrasonic Thickness Gage
-
The 45MG is an advanced ultrasonic thickness gage packed with standard measurement features and software options. This unique instrument is compatible with the complete range of Olympus dual element and single element thickness gage transducers.
-
Product
Electro Magnetic Flow Meter With Remote Display
MFI-013
-
Aarohi Embedded Systems Pvt. Ltd
MFI-013 electromagnetic flow meter is manufactured with state of the art technology. Micro controller based design provide precise measurement. A magnetic flow meter (mag meter, electromagnetic flow meter) is a transducer that measures fluid flow by the voltage induced across the liquid by its flow through a magnetic field.The physical principle at work is electromagnetic induction.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Ultrasonic Testing of Spinning Tube and Bar
ECHOMAC® FULL BODY TESTER
-
At the heart of the Echomac® Full Body Tester for Ultrasonic (UT) Testing of Spinning Tube and Bar is the unique Adaptive Pitch Control (APC) transducer carrier and the precision design “Spin-The-Tube/Bar” conveyor.
-
Product
Antennas
-
A specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
Product
Hand-Held Clamp-On Ultrasonic Flowmeter
KATflow 200
-
The KATflow 200 offers measurement performance normally associated with more complex and expensive devices and is complemented by the exceptional quality and robustness of the Katronic transducers.
-
Product
Digital Accelerometer
ZET 7151
-
The characteristics of the primary transducer are set in the device memory and measurements are performed based on those parameters. Thus, the digital sensors releases the user from setting the measuring channels and data processing. The sensors are fixed on the measurement object while the information transmission units are mounted in electric cabinets. An advantage of the ZETSENSOR units is easy installation and uninstallation as well as indication of feed and signal transmission which, in its turn, facilitates diagnostics of the system at the facility.
-
Product
PXI Pulser/Receiver Card
Receiver
The Innerspec PXI Pulser/Receiver is a high-power ultrasonic instrument designed to be installed on a standard PXI or CompactPCI chassis. The instrument provides 8kW (1200Vpp toneburst) of power which is ideal for researchers and integrators interested in a compact, high-power ultrasonic instrument to drive EMAT and piezoelectric transducers (standard or air-coupled).
-
Product
33kHz and 200kHz Dual Frequency Transducer
Model TC2122
-
Model TC2122 is a 33kHz and 200kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding. The transducer will fit Teledyne RESON SW 60/28/6029 housing and Teledyne RESON steel housings.
