Positioning Tables
align test targets with test set using a moving table.
See Also: Positioners, Hexapods, Micropositioners
-
Product
Global Positioning System Sensors
GPS
-
GPS sensors are receivers with antennas that use a satellite-based navigation system with a network of 24 satellites in orbit around the earth to provide position, velocity, and timing information.
-
Product
Signal/Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/ twin female contacts & round posts
510160113
-
This module comes fully loaded with twin female contacts & round posts (p/n's 610138200 & 610138117).iCon modules mount from the rear of the iCon/i1 receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount
510113122
-
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount.
-
Product
Signal, Module, ID, CASS, 210 Position, P4
510114122
-
Signal, Module, ID, CASS, 210 Position, P4.
-
Product
Receiver, I2 Micro ICon, 168 Position, For Crimp Contacts
310130102
-
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is made for crimp contacts. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
Vacuum, Module, Receiver, 90 Series, 2 Port Positions w/ Filter
510104266
-
Primary mating module 510108242. (May mate with other ITA modules, as well.)
-
Product
Synchro And Resolver Angle Position Indicator
AP-501
-
The AP-501 is a high accuracy, auto-ranging, broad band synchro and resolver angle position indicator. The synchro or resolver angle is displayed on a bright 0.56 inch LED display. The indicator maintains a accuracy up 0.03 degrees even with synchro or resolver phase shifts up to 45 degrees over a frequency range of 47-300 Hz. The 800B301 is a low profile rack mounted synchro/resolver angle position indicator with 360 degree offset capability via front panel thumb wheel switches.
-
Product
Eight position DB-9 Male Transition Panel
3044
-
Eight position DB-9 Male Transition Panel. ransition Panel (1 68-Pin SCSI Connector to 8 RS-232 9-Pin Connectors)
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
540295010101
-
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
-
Product
Fixed Mounting Panel, G2, 5U, 3 Position, (2 Blank Plates Included)
310113395
-
The 19" rack mounting panel offers three mounting positions for the G2 receiver without the hinging feature and is beneficial in cases where you may want to restrict wiring or instrument access.
-
Product
Table Tops Equipment
-
RECIF Technologies 150-200mm product range is composed of various kind of table tops equipment including wafer transfer, aligners and elevators.As a result of a technology license agreement, with its European partner EMU Technologies, RECIF proposes updated designs for its equipment line, without compromising the proven performances installed on the field for years.
-
Product
PMC Carrier with 2 positions
PMC-MC-X2
-
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
Module, Receiver, RTCASS, Power, 40/36 Position
510113141
-
Module, Receiver, RTCASS, Power, 40/36 Position.
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
-
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Miniature LVDT Position Sensors
-
Miniature LVDTs are ideal where reliable measurements are needed in small spaces. With options for venting up to 30,000 psi, and temperature ratings to 400°F (200°C), these LVDTs operate in hydraulic equipment, embedded in robotics, and used in harsh downhole conditions.
-
Product
Signal, Module, ITA, TriPaddle, 90 Series, 96 Position, with Right Angle Contacts
510108125
-
Primary mating module 510104135. (May mate with other Receiver modules, as well.)
-
Product
Assured Positioning, Navigation and Timing (A-PNT) Solutions
-
Curtiss-Wright Defense Solutions
Our assured positioning, navigation, and timing (A-PNT) solutions are designed to provide ground vehicles with access to trusted PNT information while operating in conditions with limited, impeded, or denied GPS/GNSS. Cost-effective, simple to configure, and size, weight, and power (SWaP)-optimized, our modules and systems are rapidly deployable on both combat and tactical wheeled vehicle platforms.
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
-
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
Signal, Module, ITA, TriPaddle, iCon Series, 96 Position
510161108
-
Primary mating module 510160108. (May mate with other Receiver modules, as well.)
-
Product
Digital Tap Position Indicator
-
NMC''s latest offering, Digital Tap Position Indicator with 4-20 mA, type TX-205, is a Micro controller based instrument used to indicate the Tap Position of the OLTC along with it transmits 4-20 mA Analog Single/Dual Output. It is a field adjustable instrument. Size : 96*96*85 mm. Aux. Supply : 85 V-265 V AC-DC.
-
Product
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position
510143006
-
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position.
-
Product
PCI Pulse Position Data Communication Board
MS 1708
-
*Bus Interface - PCI Bus*Micro controller Based Design*Shared Memory for Communication*8 Channels RS422 / Modified RS422*PPD (Pulse Position Data) Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS*Independent Intelligent Devices for RS422 and PPT Communication
-
Product
Eight position DB-9 Male Transition Panel
5100
-
Eight position DB-9 Male Transition Panel, RoHS Compliant Lead-free
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 480 Position, Unloaded
510151106
-
NOTE: Part # 510151106 Rev E and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150116. (May mate with other Receiver modules, as well.)
-
Product
Linear Position
-
The linear magnetic position sensor product family measures the linear movement of a multi-pole magnetic strip. Circular multi-pole magnetic rings can also be used in rotary incremental rotation off-axis applications. This high precision product family allows the user to detect linear movement with a resolution as fine as 0.5μm. All products are aimed at applications which require extreme precision, accuracy, dynamic range and ultra-low power consumption.
-
Product
Fixed Mounting Panel, iCon, 4U, 8 Positions, Black Anodized
310113302
-
This 4U Fixed Mounting Panel has 8 vertical positions. The iCon cover plate is sold separately (310113467). The spacing of the positions will accommodate ITA P/N's 410123102, and 410123232. Also available in a painted gray finish - P/N 310113301.
-
Product
EZ-Glider Position Control Telescoping Torque Arms
-
The position control telescoping torque arms help manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Position Control telescoping torque arms are designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. Using the EZ-Glider Position Control torque arm is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.The EZ-Glider Position Control telescoping torque arm consists of a torque reaction arm with encoders mounted at the base and a control box. The control box is used for programming and it tracks the axis movement by converting angle counts to the precise position of the screwdriver. The location is calculated from encoder values, allowing the operator to easily teach the torque arm a programmed sequence pattern and then use it to control the assembly process
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 64 Position Module To TB-4300, 10V Input
540355010201
-
Cable Assembly, Receiver, TriPaddle, 36", 64 position module to TB-4300
-
Product
Module, Receiver, RTCASS, Signal, 210 Position Right Angle PCB Mount for J4
510113140
-
Module, Receiver, RTCASS, Signal, 210 Position Right Angle PCB Mount for J4.
-
Product
Positive Displacement Flow Meters
-
Omega's Positive Displacement Flow Meters are ideal for viscous fluids such as oils, fuels, and solvents that are difficult for other types of flow meters to measure.
