Programmable AC Sources
See Also: AC Sources
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-031
Programmable Resistor Modules
The 40-254-031 (PXI) and 42-254-031 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 13.6Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-045
Programmable Resistor Modules
The 40-297A-045 (PXI) and the 42-297A-045 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 122Ω
40-252-112
Programmable Resistor Modules
The 40-252-112 is a programmable resistor module with 2 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Noise Source, 1 GHz up to 40 GHz
346CK40
Noise Source
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 925Ω
40-252-121
Programmable Resistor Modules
The 40-252-121 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
EMX-7XXX
Programmable Resistor Modules
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
PCI 3-Channel Precision Resistor Card
50-297-103
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 22.3MΩ
40-251-154
Programmable Resistor Modules
The 40-251-154 is a programmable resistor module with 1 channel which can be set between 3Ω and 22.3MΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel, 2.5 Ω to 201 kΩ
40-297A-141
Programmable Resistor Modules
The 40-297A-141 (PXI) and the 42-297A-141 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 201 kΩ, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 470
40-297-014
Programmable Resistor Modules
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 470Ω
40-253-114
Programmable Resistor Modules
The 40-253-114 is a programmable resistor module with 1 channel which can be set between 1Ω and 470Ω with 2Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
Programmable Resistor Modules
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-036
Programmable Resistor Modules
The 40-297A-036 (PXI) and the 42-297A-036 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 395 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-251-111
Programmable Resistor Modules
The 40-251-111 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Configurable Reostat or Potentiometer Module
YAV90084A
Programmable Potentiometer
4x 8-Bit 1KOhm reostat4x 8-Bit 40 Ohm reostat2x 8-Bit 5 MOhm reostat10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in self test10x Voltage to current source 0(4)..20mA10x Analog Outputs (buffer for voltage or frequency)36-Ch Test Point voltage divider2xCAN Bus Channels Terminators testerExpandable with NI PXI-6723 and PXI-6345.
-
Product
AC Power Source
LSP-500VAR
-
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 3.55kΩ
40-252-023
Programmable Resistor Modules
The 40-252-023 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-156
Programmable Resistor Modules
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-123-HI
Programmable Resistor Module
The 40-230-123-HI (PXI) and 42-230-123-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
AC Power Sources
MX Series
-
AMETEK Programmable Power, Inc.
The California Instruments MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX22.5, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-012
Programmable Resistor Modules
The 40-297A-012 (PXI) and the 42-297A-012 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 120 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-022
Programmable Resistor Modules
The 40-297A-022 (PXI) and the 42-297A-022 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 1.81 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-114
Programmable Resistor Modules
The 40-254-114 (PXI) and 42-254-114 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 470Ω with 2Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 31.5Ω
50-298-110
Programmable Resistor Modules
The 50-298-110 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 102kΩ
40-251-034
Programmable Resistor Modules
The 40-251-034 is a programmable resistor module with 4 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-032
Programmable Resistor Modules
The 40-254-032 (PXI) and 42-254-032 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 239Ω
40-252-013
Programmable Resistor Modules
The 40-252-013 is a programmable resistor module with 4 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
