Voltage
The tension of an electromotive force.
-
Product
Fanout Buffers
-
Fanout Buffers are able to create multiple copies of input signal at their output and distribute them amaong several loads while achieving fast rise/fall time and low jitter. Input and output interfaces are CML and output voltage swing can be adjusted externally.
-
Product
Impedance Stabilization Network
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
Product
In-plant Low Voltage Wet Sponge
-
Wet Sponge Holiday Detector for Plant or Stationary Operations is highly sensitive and accurate. A uniform coating of only one mil of paint or other non-conductive material over a metal surface is sufficient to repel a small current flow. If a pin-hole holiday is encountered, moisture from the sponge will seep into the hole and create a free path for electrical flow, activating the signal horn.
-
Product
Pressure Recorders
-
AMETEK Sensors, Test & Calibration
Our recorders are capable of storing gauge pressure, absolute pressure, temperature, current, and voltage. They can collect readings as quick as ten times per second, and can store up to 1 million data points. The included easy-to-use software communicates with the recorders and then saves the data into industry standard spreadsheets or tamper-proof pdf documents. With the nVision family, recorded runs can also be viewed on the graphical display of the unit itself.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
DC/DC Converters & DC/AC Inverters
-
DC/DC converters and DC/AC inverters are available for voltage conversion. With our DC/DC converters, you stabilize DC voltage, refresh the voltage at the end of long cables, and thus avoid malfunctions in your applications. Use our DC/AC inverter to convert direct current into alternating current.
-
Product
Optic Node With Amplifier
OX 755
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes cum Amplifier- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
Battery Test System
WBCS3000Ls32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
AC Power Calibrator
LS3300
-
The LS3300 is an AC signal generator capable of outputting both current and voltage simultaneously, thus allowing it to calibrate power meters. Providing output ranges of 10mV-1250V, and 0.3 mA to 62.5 A, and upto 78.125 kW, the unit is capable of calibrating up to 0.15 % Class Power meters. New features on the LS3300 include a high definition LCD display, a vector diagram, and the ability to synchronize up to three units to emulate anything from single phase two wire to three phase four wire systems.
-
Product
Digital MCA Tube Base For Gamma-Ray Spectroscopy
Gamma Stream Family
-
CAEN Gamma stream is a compact and portable system for gamma ray spectroscopy with scintillation detectors, which provides an active Multi-Channel Analyzer (MCA) integrated in a 14-pin photo-multiplier tube (PMT) base. Gamma stream fully integrates in a stand-alone device the high voltage to bias the PMT, the preamplifier to shape the signal from detector, and the MCA for a complete Pulse Height Analysis online.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-345-HI
Programmable Resistor Module
The 40-230-345-HI (PXI) and 42-230-345-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
SENSORBOX MODULE
MDGDSSBM
-
*Turn your MDMAX, MDMAX2A or MDMAX3 into a unique sensor simulator to substitute known good waveforms for intermittent components that cannot be verified*Sensor simulation tests include: DC voltage, fixed frequency, pre-defined waveform and hand-drawn waveform*Contains a library of standard reference waveforms that can be modified by the stroke of a finger
-
Product
Autoranging System DC Power Supply, 200 V, 210 A, 15000 W, 208 VAC
N8932A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
Audio Multimeter
AMM-1
-
The purpose of this tool is to enable the user to: Measure True Amplifier Power output into any load reactive or resistive Measure Common DC voltages Measure DC voltage drops during quick transients on cable runs or battery / charging systems Measure Impedance of speakers at any power or frequency from 20Hz - 1kHz (box rise) Measure Phase Difference between Voltage and Current into reactive loads (Power Factor) Find Tuning Frequency of subwoofer enclosures Tune subwoofer enclosures for maximum power transfer Measure AC Volts (amplifier output) Measure AC Amps (amplifier output)
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
Airspeed Warning Switches
-
Supply Voltage: 10÷30 Volts DC Current Rating: 200 mA max Switching Power: 5 A max 30VDC Temperature Range: -40° C to 120° C Pressure Fitting: 1/8" plastic Weight: 3.2 oz.
-
Product
PXIe-5162, 1.5 GHz, 5 GS/s, 10-Bit PXI Express, 64 MB mem, Oscilloscope
782622-01
Oscilloscope
PXIe, 1.5 GHz, 5 GS/s, 10-Bit PXI Oscilloscope—The PXIe‑5162 high-speed oscilloscope device has two or four channels that sample at up to 5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1.5 GHz of analog bandwidth and flexible measurement configurations. The PXIe‑5162 also features a high-precision triggering circuit as well as PXI synchronization and data streaming capabilities.
-
Product
Clamp Meters
-
TES Electrical Electronic Corp.
Variable Frequency drive measurement. LoZ voltage measurement to drain ghost voltages. Check 3phase sequence. True RMS reading on AC and DC+AC mode. Inrush current measurement. A measurement for HAVAC flam sensors.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
Oscillators
VCXO
-
A crystal oscillator whose output frequency varies based on an applied control voltage.
-
Product
ESD Voltmeters And Sensors
-
Achieve High Accuracy Without Fixed Spacing Requirements. We offer diagnostic tools for ESD in-line sensing and hand-held electrostatic voltmeters that are ideal for use in ESD-sensitive environments. Accurately measures surface voltage or charge build-up over a wide range of spacings.
-
Product
Flow Battery Test Stations
-
Greenlight's turn-key flow battery test systems include load/power supply modules, automated control of flow, pressure and temperature of electrolyte fluids, cell voltage monitoring, 3-level safety system and computer with Emerald dynamic automation software. All Greenlight flow battery test systems come with a our standard 1 year warranty. Our customer service team is available to travel to your facility for commissioning and training.Greenlight''s Automation Division also offers flow battery assembly equipment.
-
Product
Optical Detector
LG-9200
-
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Product
Digital Multimeter
PPDMM
-
This CAT-IV 600V Automotive Digital Multimeter by Power Probe is versatile, accurate and rugged with Large LCD Screen with Bright Backlight. Measures AC/DC Voltage and Current, Resistance, Frequency, Temperature, and Capacitance.
-
Product
Active Switching Rectifiers, 2 KW, P/N 6016C
-
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
Product
Low Voltage Solutions
-
Our market-leading range includes real-time LV monitoring systems, portable fault-finding devices, and software tools, all designed to help you proactively manage your Low Voltage network and address any faults efficiently. Stay one step ahead with our powerful insights and innovative solutions.
-
Product
Insulation Resistance Measurement
MD 15KVR
-
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
Product
Battery Load Bank
K-3980
-
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
Product
Group3 Hall probe
-
The Group3 Hall probe produces an analog voltage as its output signal, corrected for temperature effects and non-linearities, producing a signal accurate to within 0.05%, from -1 to +1 T, over 10 to 50 deg C. Group3 can offer different field and temperature ranges, and custom probe dimensions.
