UUT
assures a constituent's interoperability in a system.
See Also: Unit Under Test, DUT, System Under Test
-
Product
ABex Current Sense Module for Six Channel UUT Supply Monitoring
ABex TM-406 Current Sense
-
The ABex TM-406 is a six-channel shunt current measurement extension. It’s designed to work in combination with the Konrad ABex TM-501 and PXI-501.Each of the six shunt current measurement units have a passive measurement shunt, an overcurrent protection, a sense bridge relay and the possibility to route the quiescence current to an ABex measurement device TM-501 with PXI-501.In addition, the ABex TM-406 features 8 isolated digital outputs (IDOs), and 12 measurement inputs, which can be routed to the analog bus.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 585 x 250 mm (wxd)
CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Pylon ITA Mount Linear Testfixture Cassette and ITA Frame Not Included, UUT 306 x 248 mm
MG-02 VGR12
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with aluminum backpanel for a Genrad VGR12 Pylon frame• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2-228X (Large IF) / 230532
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
Matrix Switch Module
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
Product
Linear Testfixture (Cassette Not Included), UTT 456 x 320 mm
MG-07
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 590 x 100 x 184 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
SWB-2816, 8x46, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-16
Reed Relay
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Configurable High-Density Switch Matrix PXI Card
GX6384
Multiplexer Module
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
Product
High Speed Digital Analog
ITA
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1 Small (Hold-Down Gate) / 230154
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
QuadraPaddle 90 Series Modules
-
The versatility of VPC's QuadraPaddle twin female contacts provide four beams per end to ensure signal integrity from instrumentation to the Unit Under Test (UUT).Twin male contacts interconnect to ribbon cable, headers, and other standard connectors.Makes system configuration a simple “plug & play” operation and delivers high density, high performance interconnectivity at a lower cost per point.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
Product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
-
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
Product
RF Shielded Fixture
-
A semi-automatic, pneumatically operated fixture with a sliding pressure top provides a very short mechanical cycle-time. The unit is prepared for full, multi-station automatic operation using a centrally placed robot arm for UUT load/unload.
-
Product
In-Circuit Tester Integration
-
The benefits of boundary-scan are noticed in all phases of a product life cycle. By coupling the power of Corelis boundary-scan tools with an In-Circuit Tester (ICT), a complete, integrated solution is available that offers the best advantages of both technologies.Boundary-scan operates as the perfect companion to ICT. Boundary-scan is capable of testing areas of printed circuit board assemblies that are difficult to access due to physical space constraints and loss of physical access, which is often due to fine pitch components such as Ball Grid Array (BGA) devices. Conversely, the ICT is able to check the non-boundary-scan compatible portion of the unit under test (UUT) such as analog.
-
Product
Pneumatic Bidirectional Vertical Shock Test System
KRD17 series
-
KRD17 series pneumatic bidirectional vertical shock test system is the novel designed and developed for large specimens that cannot or are not easy to turn over, especially adopt for battery testing. It can complete vertical upward and downward shock test in one test stand without moving the UUT.
-
Product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
SWB-2816, 8x46, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-16
Reed Relay
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, … individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
JTAG USB Controller
NetUSB-1149.1/E
Controller
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 6 or 10 Positions Blocks, UUT 456 x 320 mm
MG-07-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 589 x 100 x 184 mm (wxdxh1xh2)• Equipped with dedicated cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
