Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
Switch Module
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
Oil Surface Tension Tester
-
Weshine Electric Manufacturing Co., Ltd
Surface tension is a measurement of the cohesive energy present at an interface. The molecules of a liquid attract each other. The interactions of a molecule in the bulk of a liquid are balanced by an equal attractive force in all directions. Molecules on the surface of a liquid experience an imbalance and cohere more strongly to those directly associated with them on the surface.
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
Vibration Controllers
-
The 900 Series vibration controllers incorporate Data Physics’ renowned shaker control algorithms with a modern software interface and new hardware. The 900 Series controller can quickly be set up to control any shaker – while the 900 series platform offers advanced features such as auto-aggregation of data from all test stands, custom Word-based reporting, unlimited expandability, concurrent data recording and signal analysis, intrinsic safety, and more.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Pattern Generator
-
AVLINK TECHNIC TAIWAN CO., LTD.
* Intelligent functionality. * With 162 MHz pixel frequency. * Support total 38 timings. (up to UXGA) * Support Sync Type: H/V (TTL), SOG. * Low cost. * Single interface easily use. * Portable design, working time up to 8 hours by inside Re-chargeable battery. * Auto Power-off on Battery mode. * Provide total 34 patterns, Include: Color bar, Gray, Grid, Block¡K * By 16x2 Character LCD and key buttons, easily control.
-
Product
ICD 3 Test Interface Module
AC164113
-
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
Product
PXIe-8285, 2-Port, 25 Gigabit, RDMA PXI Ethernet Interface Module
788510-01
Ethernet Interface
The PXIe-8285 is a high-performance 25-Gigabit remote direct memory access (RDMA) interface for PXI Express. This module includes two 25-Gigabit Ethernet SFP28 ports in a single-slot PXI Express module and supports RDMA over Converged Ethernet (RoCE).
-
Product
Functional Testing of Printed Circuit Boards, Sub Assemblies and Finished Products
Testpoint
-
Yelo Testpoint is an extremely modular and flexible system, allowing you to scale to any size operation, and to add almost any new test requirements. Ideally suited to cellular manufacturing, the system can be used to complement an existing ATE, as a functional test add-on, or as a diagnostic work station. Its compact, space-saving construction has multiple interface positions to accommodate both horizontal and vertical connections.
-
Product
19" Breakout & Power Input Panel
Cabinet CP-103
-
The CP-103 is breakout and power input panel which is used to provide a clear connection interface for 19” racks. It is equipped with the most common interfaces found on industrial computers. In addition, it provides a single phase 16A CEE connector and a brush to feed through additional cables and tubes. Furthermore, it’s M6 threaded plate installed to simplify equipotential bonding.
-
Product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
-
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
Product
Diode Laser Driver
D200
-
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
Product
Cable Assembly 15-Pin D-Type, Male to Female, 0.5m
40-970-015-0.5m-MF
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Programmable Video Signal Generator
VG-870B
-
The VG-870B is a standalone type multiple-interface video generator, which can test most of Flat-Panel-Display in current market. It supports the HDMI digital interfaces with the latest standard Ver.1.3a, and also supports specific functions of HDMI 1.3a such as Deep Color (max.12-bit), xxYCC and LipSync.
-
Product
MEMS Tunable Filter
-
Optoplex’s MEMS Tunable Optical Filter is based on a patented micro-optic design with MEMS tuning technology. It is an integrated module consisting of a MEMS chip, micro-optics and control electronics and interface. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). Wavelength (frequency) tuning is achieved by changing driving voltage applied to the MEMS chip, via the control electronics and the built-in firmware.
-
Product
300KHz Precision LCR Meter
Model 4300R
-
Aplab Precision LCR Meter Model 4300R is a new generation of impedance test equipment with high accuracy, wide measurement range and six digits resolution. Being featured with test frequency up to 300kHz, test voltage of 5mV ~ 2V, built-in -5V ~ 5V DC bias and -10V~10V DC voltage source output, it can meet all requirements for measuring components and materials and provide guarantees for production line quality assurance, incoming inspection and laboratory precision measurements. The Handler, RS232C and GPIB interfaces as well as improved command system provided by the instrument make it easier to build the test system.
-
Product
50 Ohm MCX to MCX Cable Assembly
40-977-561-2m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 40GHz SMA-2.9
60-801-407
Multiplexer Module
The 60-801-407 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
In-Circuit Debugger for RS08 Family of Microcontrollers
ICDRS08
-
P&E's ICDRS08 is a powerful tool for debugging code. It uses the processor's background debug mode Module(BDM), via any of P&E's RS08 compatible interfaces (see product add-ons for more information), to give the user access to all on-chip resources.
-
Product
Digital Pressure Gauge
m1M
-
AMETEK Sensors, Test & Calibration
Affordably Accurate! Featuring a 3 year recommended calibration interval, DNV approval, and an easy-to-use, time-saving user interface.
-
Product
Cable Assembly, 200-Pin LFH, Female (Male Screwlocks) to Female (Male Screwlocks), 2m
A200LFR-200LFR-6B200
Cable Assembly
This female to female 2m cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cable and the connector assemblies can be secured to their mating connectors by male screwlocks.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - XMC
Model 71610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- RoHS Compliant Lead-Free Version Available
-
Product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Low Profile PCI 8 Reed Relay Output
8012H
-
Optimized for sensing 24V inputs, the 8012H Low Profile PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs supporting 10-30V. Reed relays are well suited for low current applications. The relays are normally open, and close when energized. The board is MD1 Low Profile and Universal Bus (3.3V and 5V) compatible.
-
Product
RS232 I2C Adapter LowPower
-
*I2C frequency adjustable up to 100kHz*Maximum power consumption <5mA*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
Signal Conditioning and Filtering
MSXB 067
-
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
Product
Surveyor Thickness Gauge
Multigauge 5650
-
The Multigauge 5650 Surveyor Thickness Gauge is a simple, robust ultrasonic thickness gauge designed specifically for ship and small craft surveyors, but can also be used in applications where different measurement modes are required. The user has a choice of Multiple Echo, Echo to Echo or Single Echo to cover all requirements. The gauge can be used for metal, GRP or plastic measurement and it automatically switches modes and settings depending on the type of probe fitted. The easy to use keypad on the Surveyor Thickness Gauge allows operator interface whilst the bright LCD display can be used in all light conditions. All probes have Intelligent Probe Recognition (IPR), which automatically adjusts settings in the gauge at the same time as transmitting recognition data the result is a perfectly matched probe and gauge for enhanced performance. Additionally, the Automatic Measurement Verification System (AMVS) used with multiple echo ensures only true measurements are displayed, even on the most heavily corroded metals.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
