Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Antenna Tuning Unit
MS 2012
-
Antenna Tuning unit is used to automatically tune the notch antenna impedance. Microprocessor does tuning through tuning inbuilt algorithm. It has RS485 interface for external control unit interface. Capacitor unit (CU), Inductor unit, (IU) and RF Element are subunits of this antenna-tuning unit. System maximizes transmission.
-
Product
cPCI IP Carrier Module With Front And Rear I/O
DP-cPCI-5211
-
DP-cPCI-5211 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
Product
Instron Materials Testing Software
-
Instron offers a comprehensive suite of materials testing software solutions designed to support a wide range of mechanical testing applications, from static tensile and compression to fatigue, impact, and melt flow. Built for precision and efficiency, these software packages provide powerful tools for test control, data analysis, and reporting, with support for industry standards such as ASTM, ISO, and EN. Whether for basic quality control or advanced research, Instron’s software solutions deliver flexible, user-friendly interfaces and robust data integrity features to meet the diverse needs of modern testing laboratories.
-
Product
Rectangular Horn Antennas
-
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
Product
PXIe-8430, 16-Port, RS232 PXI Serial Interface Module
781472-02
Serial Interface
16-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m, Exit Away From Pin 1
40-970-050-2m-MF
Cable Assembly
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m HV, Exit Away From Pin 1
40-970-050-2m-MM-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
USB Digital Storage Oscilloscope, 1GS/s, 200MHz BW, 64M/channel
Acute TS2212F
-
*1. Up to 7x faster H/W initial time!*2. An additional reference clock input port to synchronize multiple-stacked DSOs!*PC-based (USB2.0 interface)*USB powered*2 channels (stackable up to 12 channels)*1 GS/s real-time sampling*200 MHz bandwidth*10K (TS2202)/64M (TS2212) points per channel
-
Product
Chassis
-
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
Product
Power ICs - Smart Load Switches
-
Combining multiple functions in a single IC, Vishay smart load switches eliminate the need for external circuitry . A simplified GPIO interface allows for power distribution and sequencing of multiple sub-systems. Slew-rate-control devices provide a controlled supply ramp to reduce inrush current, while fault protection and isolation switches increase robustness with reverse current, overtemperature, current limiting, and short circuit protection features. The ICs offer quick output discharge and small footprints, while their integrated design saves PCB space compared to discrete solutions, reduces BOM counts, and lowers manufacturing costs.
-
Product
100-Pin Micro-D Connector, Right Angle PCB Mount, Female, 2-56 UNC Screwlocks
C100SFX-1PR-5A
SCSI Female Connector
Female right angle PCB mount 100-pin Micro-D connector allows a user to create their own PCB based termination solution. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-6 FPGA - XMC
Model 71662
-
- View product video- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Up to 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable serial gigabit interfaces- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
-
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
Product
WDXRF Spectrometer
S8 TIGER Series 2
-
Thanks to HighSense technology the S8 TIGER Series 2 WDXRF spectrometer delivers for all elements accuracy and precision for industrial quality and process control. With high resolving WDXRF technology and optimal detection of light, medium and heavy elements based on the new HighSense beam path, the XRF2 mapping tool of the S8 TIGER Series delivers best sensitivity, smallest spot size, and highest resolution for small spot applications. Ergonomic and failsafe operation are vital for efficiency and best analytical data. Simple, intuitive start of samples are guaranteed with the multilingual TouchControl interface.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
779787-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
Interface Card
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
-
Product
Chassis Controllers and Bus Expanders
-
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
Product
SIMRC - 16 x Uncommitted Reed Relay, SPST Screened
1010-R-16-1RF-5/1D
Reed Relay
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Network Emulation System
Mini Maxwell
-
Mini Maxwell -- Easy to use, portable, network emulator. Mini Maxwell''''s low cost of $1995 can fit into any testing budget. The Mini Maxwell is great if you have low power requirements, or need ultra quiet operation. Mini Maxwell supports packet drop/loss, duplication, delay (latency)/jitter, reorder, and burst. Includes: processor, memory, and three Ethernet interfaces in one enclosure with separate power supply, Linux OS, Mini Maxwell network emulator engine, graphical user interface, and 90 Day Warranty.
-
Product
3 Channel Sync/Async Serial Interface PCI Mini Card
TMPE863
-
The TMPE863 is a standard full PCI Express Mini Card, providing three high speed serial data communication channels.
-
Product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
-
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
Product
Avionics Interface Technology
-
The modules are available as PXI, PCI, PCI Express, USB, VME, VXI and many more
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 0.5m, Exit Towards Pin 1
A050DM5-050DM5-0A050
Cable Assembly
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Water & Weather Node
SmartGuard
-
The next generation sensor and instrument HUB for Ocean, Lake, Reservoir, Estuary and River Hydrometric stations.Monitoring water and weather conditions is essential in many operations and the SmartGuard node is well suited for stand-alone stations powered by battery and solar power utilizing wireless real-time data communication.Designed for ease of integration of new and existing sensor technologies into a single Aanderaa observatory node with modern self-describing XML data output formats.SmartGuard interfaces with all Aanderaa atmospheric and in water sensors, along with most 3rd party sensors.
-
Product
PXI Single 24:1 High Voltage Power MUX
40-331-001
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends
A050DF4-T-0A100
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
MultifunctionAsync Serial Communications Adapter
2628
-
The Multifunction RS422/RS485/Digital I/O board provides a collection of various interfaces on a single-wide PMC module. The two 16550 UARTs on the board provide asynchronous communication at bit rates to 115Kbaud. The 16550?s are mapped into host processor space so that standard drivers can be used with the board.
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
