-
Product
PoE Splitters
-
Power Over Ethernet PoE Splitter splits the data and power signals that are transmitted from Power Sourcing Equipment. A PoE splitter makes the exact invert operation: by the means of a PoE splitter, the power and the data received on the Ethernet cable are split. The power can then be used to power any other electrical device present in the application.
-
Product
WebSensor with PoE
T0610
-
Ambient temperature t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
Product
PoE Module
-
PoE-PSE I/O boards comply with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device
-
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9516E-8GMPX
-
8 x M12 D-Coded 10/100 Mbps PoE ports + 4 x M12 X-Coded 10/100/1000 Mbps PoE Ports + 4 x M12 X-Coded 10/100/1000 Mbps ports. Complies with EN50155 & EN50121-3-2, Operating temperature: -40 ~ 75°C, Operating power input range: 16.8~137.5VDC.
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9528G-4GMPX
-
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, 24 x PoE IEEE802.3af/at ports. Wide nominal power input range: 24 ~ 110VDC, Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence.
-
Product
PoE Injector
-
Our PoE Injectors support Power Over Ethernet powered devices in industrial environments. They deliver both data and power over a single standard Ethernet cable to a PoE powered device designed to receive both data and power through its RJ-45 port connector.
-
Product
Reach Power-over-Ethernet (PoE) Testers
-
After assembly, electronic equipment manufacturers need to test functionally of their products. They want to provide the most test coverage, in the shortest time, for the least cost. When test engineers develop product test plans, they select the most appropriate off-the-shelf general purpose test equipment available. Reach designs and manufactures custom test equipment which is a better fit than general purpose equipment. It not only reduces test time but also reduces costs.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Gigabit (PoE), 2 Port, Network Interface Card
Ethernet Network Interface Card
-
Gigabit (PoE), 2 Port, Network Interface Card
-
Product
8FE PoE And 2G Combo Managed Ethernet Switch
EKI-7710E-2CPI
Ethernet Switch Module
Certified to IEC 62443-4-2 SL2, 8 x IEEE 802.3 af/at PoE Fast Ethernet ports + 2 x Gigabit Copper/SFP combo ports, Redundancy: Gigabit X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D) IXM function enables fast deployment, Security: 802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption), RADIUS.
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9528E-12GMPW
-
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, 24 x PoE IEEE802.3af/at ports. Wide nominal power input range: 24 ~ 110VDC, Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence.
-
Product
PoE-PSE I/O Board
AX93280
-
*PoE-PSE I/O board complies with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device
-
Product
8GE PoE And 4G SFP Managed Ethernet Switch
EKI-7712G-4FPI
-
Certified to IEC 62443-4-2 SL2, 8 x IEEE 802.3 af/at PoE Gigabit ports + 4 SFP ports, Redundancy: X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D) IXM function enables fast deployment, Security: 802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption), RADIUS.
-
Product
1GE PoE, SFP Injector ,IEEE802.3af/at, 24~48VDC, -40~75℃
EKI-2741FPI
-
Supports multi-rate for SFP slotIEEE 802.3af/at compliantPower input 24-48 VDC, supply 30W per portProvides slim size and DIN-rail/Wall mount with IP31 metal mechanismSupports operating temperatures from -40 to 75°C
-
Product
6GE Port Gigabit Unmanaged Industrial PoE Ethernet Switch
EKI-2706G-2GPI
Ethernet Switch Module
6 Gigabit RJ-45 Ethernet ports. Support 4 x IEEE 802.3at/af PoE ports for PD demands, Up to 30W output per PoE port. Supports jumbo frame transmission up to 9k bytes, 12 ~ 48 VDC redundant dual power input and 1 relay output, Wide operating temperature range of -40 ~ 75°C.
-
Product
8GE PoE And 2G Unmanaged Ethernet Switch
EKI-5729PI
Ethernet Switch Module
Full Gigabit Ethernet ports and comply with IEEE, 802.3af/at PoE standard, Communicates with SCADA software via Modbus/TCP. Communicates with NMS (Networking management system) via SNMP, Port-based QoS for deterministic data transmission.
-
Product
8GE+4G SFP Port Gigabit Unmanaged PoE Switch
EKI-2712G-4FPI
Ethernet Switch Module
Dual 48 VDC power input and 1 x relay output, -40 ~ 75°C wide-range operating temperature, EN50121-4 approval for railway trackside deployment. NEMA TS2 for traffic control, SFP socket for easy and flexible fiber expansion, 8 x IEEE 802.3 af/at PoE Gigabit ports + 4 x SFP ports.
-
Product
8GE Port Gigabit Unmanaged Industrial PoE Ethernet Switch
EKI-2708G-PI
-
8 x Gigabit Ethernet ports, Support 8 x IEEE 802.3at/af PoE ports for PD demands, Up to 30W output per PoE port. Supports jumbo frame transmission up to 9k bytes, 12 ~ 48 VDC redundant dual power input and 1 relay output, Wide operating temperature range of -40 ~ 75°C, Supports EMC Level 4 protection for extreme outdoor environments.
-
Product
E-Mark M12 8FE PoE + 2GE Managed Switch
EKI-9510E-2GMPS
-
M12 connector with IP67 rugged housing, Complies with E-Mark, Complies with UN ECE R118 & UN ECE R10. Supports PoE IEEE802.3af/at (PoE model) Wide nominal power input range: 12/24VDC; Operating power input range: 9-36VDC. Compact size to fit in different narrow spaces, Operating temperature:-40 ~ 70°C.
-
Product
8GE + 2G SFP Port Gigabit Unmanaged Industrial PoE Ethernet Switch
EKI-2710G-2FPI
Ethernet Switch Module
8 x Gigabit Ethernet ports plus 2 Gigabit SFP ports, Support 8 x IEEE 802.3at/af PoE ports for PD demands, Up to 30W output per PoE port. Supports jumbo frame transmission up to 9k bytes, 12 ~ 48 VDC redundant dual power input and 1 relay output, Wide operating temperature range of -40 ~ 75°C.
-
Product
8GE+4 10G SFP L2 Managed PoE+ Switch
EKI-7412G-4XP
-
8 Gigabit Ethernet Ports and 4 10G SFP Ports, 0 to 60°C operating temperature range, Supports 8 IEEE802.3af/at PoE ports. 140W PoE Power Budget, Management: SNMP v1/v2c/v3, WEB, Telnet, Standard MIB, IXM Function Enables Fast Deployment.
-
Product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
-
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
Product
EN50155 Managed PoE Switch
EKI-9528E-12GMPX
Ethernet Switch Module
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, 24 x PoE IEEE802.3af/at ports. Wide nominal power input range: 24 ~ 110VDC, Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence.
-
Product
Web Sensor with PoE
T3611-4
-
Ambient temperature, relative humidity t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
Product
PoE Tester
PE-100
-
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
-
Product
Non-Standard PoE Tester
PE-300
-
set up No-standard PoE system and help to troubleshoot connection issues.
-
Product
HDMI Matrix Switch Over HDBase-T with Power Over Ethernet (PoE)
SM-8X8-C6HDR-POE-HDBT
-
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
Product
PoE Modbus TCP Based Dual Ethernet Port I/O Modules
-
The PET-7200 Series are communicable over Modbus TCP, can be Powered over Ethernet (PoE) and have 2 Ethernet ports for daisy chain configuration. The built-in two-port Ethernet switch is to implement daisy-chain topology. The cabling is much easier and total costs of cable and switch are significantly reduced. They are configurable over a built-in web server and have a Web HMI.
