Breaker Test Systems
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT M3K+
-
SCOT M3K+ measures and displays CLOSE, OPEN and CLOSE-OPEN times of Main contacts of 3 poles connected end to end, simultaneously. Ideally suitable for CBs with single break per pole.
-
Product
5G Carrier Acceptance Test System
NetOp
-
R&S®NetOp is the leading platform for network operator device acceptance test, covering all leading tier 1 operators.As one-stop shop for Protocol, IMS, Data Performance, E911 GNSS the supported carriers include:North America: AT&T, Verizon Wireless, T-Mobile USLatin America: America MovilChina: China Mobile, China Unicom, China TelecomJapan: NTT DoCoMo, Softbank, KDDI
-
Product
Test Automation Platform Deployment System
KS8000A
-
TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments. The Keysight KS8000A Test Automation Platform (TAP) Deployment System provides a lower cost, scaled down alternative to the full KS8400A TAP Developers System without the graphical user interface, results viewer and timing analyzer. Deploy your existing test software and TAP plugins into manufacturing environments using the KS8000A command line interface or your own interfaces.
-
Product
Multi-site Module Testing System
TCIII-3200ST
-
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
Product
System
SYS-36
-
Systems with 36" chambers tend to be a customer favorite for their flexibility. They are easily used for many different types of coatings. Often times they are best utilized in a prototype or multi part production facility where a specialized system such as a dual chamber box coater is not required. They are, however, still configurable for specialized processes.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Defined CRPA Test System
BroadSim Wavefront Software
-
Protecting your GNSS systems from jamming and spoofing is more critical now than ever before. BroadSim Wavefront was designed to enable easier and more affordable CRPA receiver testing, leveraging proven software-defined architecture.
-
Product
Test System
USB Explorer 280
-
The Ellisys USB Explorer 280 is a sophisticated protocol test and analysis system for USB SuperSpeed traffic monitoring, driver and software stack debugging, and performance analysis.
-
Product
Stationary Circuit Breaker Testing
ACTAS L260
-
High-precision test system for function tests on various types of switchgear device, including circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit.The inputs and outputs are connected flexibly via a terminal strip, making the test system particularly suitable for use in development and laboratory environments as well as in production environments.
-
Product
Measuring Systems For Night Vision Systems
Visual Resolution Test Of Image Intensifiers
-
Optik Elektronik Gerätetechnik GmbH
Visual evaluation of image intensifier tubes with regard to resolution and image quality.
-
Product
Shock Test Systems
-
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
Product
Goniophotometer Test System For Led Lamp
1680A 1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
UV-VIS Systems
-
The tec5 UV systems offer fast and reliable measurements starting from 190 nm. The modular system platform enables multiple integration options for easy and efficient handling of various measurement tasks in research and production applications. Due to the system’s dedicated design for industrial processes, even applications in harsh environments are possible without any difficulties, including simple and safe connection to process control systems utilizing common interface concepts established on the market.
-
Product
X-ray Non-Destructive Testing (NDT) System
DynamIx HR / Series 5
-
High precision 12-bit 50µm reading allows inspection of minute image details. Wide dynamic range resulting in wide allowance of X-ray exposure value.
-
Product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
-
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
Product
System Components
-
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
Product
Tan Delta Test System
-
Precision measuring bridge is designed for determining the capacitance and dielectric dissipation factor of liquid and solid insulants, cables, capacitors, line transformers, generators, motors, bushings etc. Furthermore it can also be used for power loss measurement on shunt reactors or similar apparatus. This system is suitable for both low and high voltage measurement at line frequency. Measurement reports can be printed. This measuring equipment has been specially developed to maximise efficiency in production and quality control environments. Its outstanding accuracy also makes it suitable for laboratory and research applications.
-
Product
Modular Hydrostatic Test System
-
Our modular hydrostatic test chambers are designed with open ends to accommodate the connection to similar units for the purpose of lengthening the enclosed test area. The modular test system starts with a base unit with complete pump system, gauges and controls mounted on the 60” x 24” x 18” test chamber. If longer test lengths are required, simply add another test chamber to double, triple or quadruple the test length area. Specify your particular requirements at our Customization Page.
-
Product
Meter Test Systems
-
We offer a huge variety of products for meter testing. From the smallest device with the size of a single-phase meter up to customized semi-automatic systems with more than 40 test positions.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Hydraulic Test Systems
-
Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.
-
Product
Millimeter-Wave Automated Accelerated Reliability Test Systems
nm-Wave AARTS System
-
AARTS fully integrated, automated, turnkey system provides flexibility and accuracy in determining RF and DC performance degradation with aging to predict life expectancy for compound semiconductor devices. Our millimeter-wave Automated Accelerated Reliability Test Systems (AARTS) and fixture solutions are available in standard frequency ranges from 26.5 to 67 GHz.
-
Product
6-Axis Robotic Automated Testing System
AT6
-
The Instron AT6 is a flexible, robot-assisted testing solution featuring six axes of motion, purpose-built to automate tensile, compression, flexural, and lap shear testing in alignment with widely used ASTM and ISO standards. Its modular design accommodates a broad array of materials—including metals, polymers, elastomers, films, composites, and sutures—at force capacities up to 600 kN. Capable of processing up to 500 specimens without operator intervention, the AT6 enables true unattended or “lights-out” operation, significantly increasing throughput around the clock. Optional modules include stations for specimen measurement, automated strain measurement, environmental temperature chambers, and multiple test frames for simultaneous testing. The system also integrates smoothly with auxiliary devices such as durometers, hardness testers, and surface roughness testers, making it a robust solution for high-volume, high-efficiency testing environments.
-
Product
Miniature Vibration Test System
G-2 Series
-
The G-2 Series Miniature Vibration Test System, though compact & handy, consists of a sweep oscillator, sine controller, power amplifier and vibration generator, thus suited to a variety of applications; calibration of sensors, standardized vibration tests for small parts, school teaching materials and modal analysis. The G-2002 is handy, with all the composed units being incorporated in a portable case.
-
Product
Mobile Systems
-
Advanced vehicle-based platforms for real-time detection and identification of CBRN threats in complex and variable urban environments.
-
Product
Telemetry Systems
-
For Automotive, Aerospace, Marine, Motor & Generator Health, Energy, Power Plant, and Industrial Applications.
-
Product
Test Automation System for Driveline Testing
STARS Driveline
-
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
Product
NFC Physical Layer Test System
IQnfc+
-
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
Product
Medalist i1000D
U9401B
-
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
