Breaker Test Systems
-
Product
EMC Test Systems
IEC61000
-
N4L are the only IEC61000 EMC test system manufacturer in the world* with an on site UKAS ISO17025 calibration laboratory offering accreditation to IEC61000-3-2, IEC61000-3-3, IEC61000-4-7 and IEC61000-4-15. Calibration and trace-ability are a vital aspect of any EMC test solution and the coverage provided through N4L’s UKAS Laboratory is comprehensive. N4L’s IEC61000-4-15 calibration procedure is particularly noteworthy as it covers the entire test protocol detailed in Annex C of IEC61000-4-15. It is commonplace for specific parameters within IEC61000-4-15 (d parameters are frequently omitted from calibration procedures) to remain untested during typical flicker calibration due to the difficulty in providing trace-ability for such measurements. All tests within the test protocol of Annex C are included within the scope of accreditation and calibration procedures at N4L.
-
Product
Cable Free ATE
CABLEFREEATE
test
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Circuit Breaker Endurance Test System
-
Endurance testing involves operating – closing and opening – the circuit breaker repeatedly for a set number of cycles. This test is necessary to stabilize the circuit breaker mechanism and to identify “Early Infant Mortality” failures in the switchgear assembly.
-
Product
EMC Test Systems
-
The sum of EMC is not necessarily equal to its parts; any modular electronic device from a complete aircraft down to a mobile phone needs to meet EMC requirements for the device itself, even if all the individual modules are compliant. For the enormous range of types of modular device requiring EMC test, R&S offers extremely flexible and scalable EMC test systems; practically as modular as the devices under test.
-
Product
Three-Phase Test System
TESTRANO 600
-
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
Product
Photoelectrochemical Test System
ModuLab XM
-
The system, based upon Solartron Analytical's world-leading experience in transfer function measurements, offers a high-quality measurement platform for characterizing a range of photoelectrochemical devices such as DSSC's, Perovskite cells, and Photoanodes," noted Professor Laurie Peter, world leading expert, University of Bath, UK. Professor Peter acted as scientific advisor during the development of the ModuLab PhotoEchem system and helped ensure the system met the requirements of the most demanding photovoltaic researchers in the market today.
-
Product
SR/QE Testing System
PVE300
-
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
Product
Test System
NFC Xplorer
-
The CISC NFC is a compact, high-quality test system, developed for HF RFID and NFC devices measurements and performance and conformance tests.
-
Product
NI's Wireless Connectivity Functional Test Solution
Functional Test
The proliferation of wireless functionality in electronic devices is pressuring test developers to deliver more complex testers within shrinking project schedules. Evolving standards and the integration of multiple wireless technologies into new product designs mean developers must prioritize measurement speed and quality to maintain throughput and yield targets. For a solution to meet these sorts of demands, it must:
-
Product
Meter Test System
MTS-50
-
Kongter Test & Measurement Co., Limited
This meter test equipment features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 50A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Test System
Griffin III
-
The Griffin III system brings new price/performance efficiency to the Tester-in-a-Head tradition, a concept created and introduced by HILEVEL in 1987. This tester is a superior cost-effective solution for Engineering, Production, and Failure Analysis test applications.
-
Product
RFID Test System
-
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
-
Product
Hydraulic Test Systems
-
Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.
-
Product
System Test Fixture
-
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
Product
Meter Testing System
ASTel
-
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Test System
RF-1 ATS
-
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Conformance Test Systems
-
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
Product
Test System
LPDDR4 and LPDDR3
-
Testing LPDDR4, LPDDR3 devices is made fast and simple with the "Lower Power" LPDDR4/3 TCE-3200LP IC test system. It can be configured up to 32 sites in parallel and integrated with the customer's selected handler.The TCIII-3200LP system can be used as a production tool as well as an engineering tool. To assist manufacturers and integrators, TurboCATS has developed a heat chamber that can be integrated with the TCE-3200LP, LPDDR4 and LPDDR3 test system. This allows the devices to be tested while being exposed to heat conditions.
-
Product
Battery Test Systems
-
Was designed to meet the specific demands of our loyal customers. This system is used to test both single cell batteries as well as super-capacitors.
-
Product
Commercial Test Systems
-
IR Target Projectors, IR/Visible Target Projections, Wide FOV Target Projectors, Focal Plane Array Tester, Fused IR/Visible Projectors, High Volume Tester, IR/Visible Ranging Projectors, Dual Blackbody Wide FOV, Future Test Requirements.
-
Product
Test System
4003 TLP+™
-
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
Product
Test Cell System
qCf FC25/100
-
The quickCONNECTfixture with an active fuel cell area of 25 cm 2 has been an integral part of our product portfolio since 2006. The excellent properties and the patented design of the cellFixture offer enormous advantages in the characterization of cell-internal components for fuel cells and electrolysis.
-
Product
VME Data Acquistion System
ADM-31
System
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
Optics Test Systems
MTF Measuring Device For Endoscopes
-
Optik Elektronik Gerätetechnik GmbH
Manual MTF measuring device for endoscopes. The measurement setup is based on modular individual components that can be arranged on a breadboard according to the type of endoscope (angle between light entrance and eyepiece).
-
Product
Pump Test System
-
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
Nanomechanical Test Systems
-
Bruker’s nanomechanical test systems deliver the highest degree of performance, accuracy, reliability, and versatility for quantitative mechanical and tribological characterization at the nanoscale and microscale. Utilizing multiple patented and proprietary technologies, the Hysitron product line of standalone nanomechanical test systems enable quantitative characterization at length scales unreachable by others.
-
Product
Test systems
-
MG Products can supply a variety of test systems. These include the Extended Boundary Scan Test from JTAG Technologies, the functional test equipment integrated into a table or high configuration from Unites systems or the Cabinet Modular Test solution (CMT). We offer the right solution for every test setup.
