-
Product
Steering Diodes
-
ProTek's low capacitance Steering Diode Arrays provide high-speed data line and I/O port protection from transients caused by Electrostatic Discharge (ESD), Electrical Fast Transients (EFT), Tertiary Lightning and other induced voltages. Steering diodes divert the transient to the power-bus or ground and away from sensitive IC components.
-
Product
ITSM Synchro
-
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
Product
Level Switches
-
Omega can meet your level measurement requirements by offering switches of various technologies including capacitance and conductivity, tuning fork, ultrasonic, optical, and rotating paddle switches.
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
-
Product
Passive Probe, 10:1, 350 MHz, 1.3 M
N2872A
Oscilloscope Probe
Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2870A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.
-
Product
8 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 804HD-MS
Oscilloscope
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
RA Family Of Arm-based MCUs
RA4
-
The RA4 Series bridges the needs for reasonable low power with the demand for connectivity and performance. These MCUs deliver up to 48MHz of CPU performance using an ArmⓇ CortexⓇ-M4 core with up to 256kB of embedded flash memory. The series offers a wide set of peripherals, including USB, CAN, ADC, capacitive touch, a segment LCD controller, and additional security IP integration, making it suitable for industrial equipment, home appliances, office equipment, healthcare products, and meters.
-
Product
Schottky Barrier Bridge Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
Oscilloscope: 500 MHz, 2 Analog Channels
DSOX4052
Oscilloscope
The 4000 X-Series boasts 12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology and standard segmented memory.
-
Product
Climate Test
Series C
-
With our CTS climatic test chambers, you can also simulate the stress factor humidity in your tests next to the temperature. The humidity is measured by a capacitive moisture sensor, which is characterized by high accuracy, long term stability and low maintenance.
-
Product
WaveSurfer Oscilloscope, 500 MHz Bandwidth, 4 Input Channels, 4 GS/s, 20 Mpts/ch - interleaved
WaveSurfer 3054z
Oscilloscope
500 MHz, 4 GS/s, 4 Ch, 10 Mpts/ch DSO with 10.1" Wide screen Color, Capacitive Touch Screen Display.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Fluid Level Sensor
-
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
Product
CCTV testers
-
1.IPC Tester ,Support H.264/H.265 4K HD IP Camera.2.POE 48V Power Output,Max 24W;3.Support ONVIF, dahua, Hikivision, ACTi,samsung IPC.4. 4.3 inch 800*400 capacitive screen, image display more clearly;5.Built-in WIFI function,can test the Wi-Fi IP Camera;6.Support IP PTZ control functions (ONVIF).7.Support DC12V1A power supply output.8.Support Audio input test.9.Support 4K HD video files and Screen projection function.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix topology With Column Protection Resistors
782385-12
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX4052A
Oscilloscope
500 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Oscilloscope: 350 MHz, 4 Analog Channels
DSOX4034G
Oscilloscope
The 4000 X-Series boasts 12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology and standard segmented memory.
-
Product
InfiniiVision Oscilloscopes
3000T X-Series
-
100 MHz - 1 GHz, DSO and MSO models Speed testing with simplified operation and documentation enabled by the 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone Touch Triggering See the most signal detail with 1,000,000 wfms/s update rateQuickly modulate and characterize signals with built-in WaveGen 20 MHz ARB, 3-digit voltmeter and 8-digit frequency counter & totalizer options Decode serial busses faster with hardware-based serial analysis options Protect your investment with full upgradeability
-
Product
On-Line Moisture Meters
-
Many methods are available for measuring moisture content on line, in real time: NIR, RF Capacitance, NMR (Nuclear Magnetic Resonance), and Microwave, among others. Finna Sensors is unique in that it has experience with most of these methods and is therefore able to recommend the best possible solution for any application.
-
Product
High Impedance Active Probes
7A
-
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
Product
1000 Amp AC/DC Digital Clamp Meter
DL6402
-
With inclusion of DC current temperature & capacitance readings, this clamp meter is the ideal all purpose instrument.The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
Product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
-
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
FA Leakage Switch Mainframe
B2200A
Mainframe
The B2200A reduces the cost of test by enabling characterization tests to be automated, without compromising the measurement performance of the semiconductor parameter analyzer. It supports a 4-SMU, full-Kelvin configuration and a capacitance meter, with room for future expansion. Includes 14 inputs, each with a unique internal measurement path, and a distinctive capacitance measurement compensation feature for two of the inputs. Provides front panel control via keypad or optional light pen, and supports instruments such as pulse generators.
-
Product
Level Indicators
-
4B has a wide range of radio frequency (RF), rotary paddle and capacitance point level indicators for detecting high, intermediate, or low levels of liquids, powders and free flowing granular solids stored in tanks, bins, silos or other containers. Certain units can also be used as plug or choke detectors in chutes, conveyors and elevator legs.
-
Product
Level Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Level trainer is a table top module, it comprises of measuring tank of 50 CM length, sump tank and load cell capacitance as level sensor. A vertical pump is fitted circulate the water. Digital display indicator is provided display water level in cm
-
Product
4 Channel Oscilloscope
2565B
-
The 2560B Digital Storage (DSO) and Mixed Signal Oscilloscope (MSO) Series offers 100 MHz, 200 MHz and 350 MHz bandwidth models in a 4-channel configuration, with a sample rate of 2 GSa/s and a maximum memory depth of 200 Mpts. Additionally, these oscilloscopes are equipped with a large 10.1" capacitive touch display that provide 1024 x 600 resolution and intuitive touchscreen gestures.
-
Product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
Product
Oscilloscope: 1.5 GHz, 4 Analog Channels
DSOX4154G
Oscilloscope
12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology, and standard segmented memory
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
Multiplexer Module
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
