Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 5690 DTC Blvd.
Suite 550E
Greenwood Village, CO 80111
United States of America
-
Product
Transverse Planer Moisture System
MC PRO 2400
-
Maximize grade recovery with Finna Sensors' highly accurate transverse planer meter. The most widely-adopted transverse sensor system acts as a dropout or easily integrates with auto graders. Integration via ProTrac software, with barcode or manual tracking, provides advanced kiln analysis and drying reports.
-
Product
Model V: Veneer Moisture Meter
MRC003304
-
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
Product
Sawmill Green Lumber Sorting System
-
The transverse sawmill meter sorts pieces into four moisture groups with similar drying characteristics by assigning a dry-ability index number. This critical first step in end-to-end moisture control improves kiln performance by reducing aggregate standard deviation and total drying time when compared to unsorted loads.
-
Product
Model A8: All-Purpose Moisture Meter
N/A
-
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of paper or paperboard. Covers 3" a diameter (7.6mm) and penetrates 3/4" (1.9cm). Reliable, long battery life. Includes a rechargeable battery, carrying case, and operating instructions book.
-
Product
Model T8: Thin Materials Moisture Meter
MRC001970
-
Uses radio frequency capacitance to measure moisture. Provides average moisture content down to a penetration of 1/8 to 1/4 of an inch. Has three concentric rings that cover an area 3 inches in diameter
-
Product
Model B: Concrete Moisture Meter
MRC003305
-
Specifically designed for the concrete block industry. Includes calibrations for over 34 different kinds of concrete block. Direct reading scales for average percent moisture content.
-
Product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
-
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
Product
Precigrader: Acoustic MSR System
-
Precigrader is an acoustic on-line strength grading system. The system is installed in more than 150 mills. It is used to determine common commercial grades in North America, including 1650 and 2100. A spring-loaded impact mechanism strikes the lumber as it passes. The resulting vibration is captured by microphones to determine the appropriate MSR grade.
-
Product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
-
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
Product
Model LGF: Gypsum Moisture Meter
MRC006522
-
Stainless steel flat plate electrode. Excellent for testing Gypsum Wallboard as it moves or in stacks. Measures moisture in the Gypsum plasterboard 1/4 inch to 3/4 inch thick. Can also check moisture distribution pattern and length or width.
-
Product
SMART III RF Probe
-
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
Product
Lab Moisture Analyzer
-
PC-Based laboratory/production Moisture Analyzer connects through the RS-232 Serial Port. For nuts, granules, powders, pellets, chips or flakes. Complete with:– MCPC-RS Test Chamber– Windows PC-Based Software– Two Sample Cups– Dial Thermometer– Standard Block– RS-232 Cable (10 Feet)– USB to RS232 Adapter– Operating Instructions Manual– 115VAC/60HZ Wall Transformer
-
Product
Model L: Lumber Moisture Meter
MRC003303
-
Calibrated for 77 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 3/4" penetration. Rechargeable battery.
-
Product
Handheld Moisture Meters
-
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
Product
Model AM-III: Paper Moisture Meter
AM-3003
-
Portable instrument that permits instantaneous, nondestructive measurement on all types of paper and paperboard. Immediate, accurate readings on moving or stationary rolls, stacks, or reams. Includes a library of frequency and operation modes used to minimize the influence of pH and temperature. Provides greater quality and throughput of product.
