Winding Ohmmeters
-
Product
Bobbin Winding Coil Turns Tester
SS108A series
-
Bobbin winding coil testers are used to test various coil of turns. Such as: generator winding turns, transformer winding turns, motor winding turns, inductor winding turns, contactor winding turns, relay winding turns, sparking winding turns, ignition winding turns, speaker voice coil, etc.
-
Product
IMPULSE SURGE WINDING TESTER
VE2882A-5U
-
Impulse Tester can detect turn & layer short ,the differences in the number of turns and the material of the core. If high impulse voltage is applied, the poor insulation will appear as a corona or layer discharge.
-
Product
Portable Winding Resistance Tester
-
1. Handheld winding resistance meter2. Conversion function for standard temperature resistance.3. 500 test data can be saved and download by flash disk.4. Temperature testing function.
-
Product
Winding Resistance Meter 100Amps, 2 Channels
WR100-12R
-
Raytech Digital Winding Resistance meter WR100-12R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Wind Sensor
FT722
-
Specifically designed for wind turbine control, the FT722 reads wind speeds from 0-50m/s. Its inovative design incorperates a series of "turbulators" (patient pending) which condition the air flow. With updated software, and calibration in our new state-of-the-art wind tunnel, the FT722 delivers our highest levels of accuracy in wind speed, wind direction and accoustic temperature measurement.
-
Product
Winding Resistance Meter 50Amps, 3 Channels
WR50-13
-
Raytech Digital Winding Resistance meter WR50-13 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Wind River Linux
-
For more than 15 years Wind River Linux has been the industry’s most advanced embedded Linux platform, with a comprehensive suite of products, tools, and lifecycle services to build and support intelligent edge solutions.
-
Product
Winding Resistance Meter 50Amps, 2 Channels
WR50-12
-
Raytech Digital Winding Resistance meter WR50-12 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Wind Measurement and Meteorological System
Moriah
-
Aeronautical & General Instruments Ltd.
MWS is a solid-state system with no moving parts, so providing a highly accurate, reliable and low cost of ownership system, which is ideal for supporting ship based aviation activities. The system comprises of 1 to 5 Solid State Wind Sensors, Dual Redundant Processor Unit, a range of Multi-Function Color Displays (8.4”, 10.4” and 15.0”) and utility Software/Graphic User Interfaces. In addition full Meteorological capability can be achieved with the inclusion of Air Temperature & Humidity, Air Pressure and Sea Temperature Sensors.
-
Product
Wind Turbine Performance Lidar
Wind Iris
-
The Wind Iris is based on Leosphere's leading WINDCUBE pulsedLidar technology, and is the first remote sensor dedicated to turbine-mounted measurements. It measures the horizontal wind speed and direction from 40m to 400m upwind of the turbine. Real time and average data can then be transferred automatically or stored in a data logger.
-
Product
OHMMETERS
DOT-1000-2
-
Model DOT-1000-2, is an ac four-terminal ohmmeter to be used for the measurement of dynamic ac resistance of batteries, fuel cells and other voltage sources.
-
Product
Wind Direction Sensor
ENVIROMUX-EWDS
-
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
-
Product
Micro - Ohmmeter / Milli - Ohmmeter
-
Basic Accuracy 0.25%Max. Test Current : 5A (120mV) for 7002Max. Test Current : 10A (60mV) for 7272Manual or Auto RangeFour Terminal Kelvin Measurement6 Ranges with 1mV Best ResolutionMeasurement of Resistive and Inductive MaterialsSetting for HI, LO & PASS ReadingsMemory of 3000 Measurements DataProgrammable HI-LO Alarm with memory of 20 DataLarge LCD with Backlight & HOLD FunctionLow Power ConsumptionBattery Operated with AC AdaptorLow Battery (Voltage) AlarmLED indication for Invalid Resistance MeasurementCable Length Measurement in feet & metersUser Interface Software for PC Communication via RS232C(to USB Bridge) cableBuilt-inBatery Chaging Circuit & Calender Clock
-
Product
Winding Resistance Test
20A DC booster
-
The 20A DC STCS booster allows to perform resistance tests on a PT with a current up to 20 A DC. The option is used together with STS 5000 and STS 4000 and must be connected to STCS module.
-
Product
Solid-State Wind & Meteorological Measurement System
AGIMET
-
Aeronautical & General Instruments Ltd.
AGIMET uses the latest proven solid-state meteorological sensor technology specially designed for the marine environment to provide accurate measurement of wind speed and direction, temperature, pressure, humidity and other local environmental parameters.
-
Product
Transformer Winding Resistance Testers / TRT ? 27
TRT-27 series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Fast measurement: Test current 2.5A to 20A, Digital display of resistance and test current.
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
Wind Tunnels
-
Omega's Wind Tunnels come in benchtop or floor standing models for any research, manufacturing, or quality control application. All Wind Tunnels are manufactured in The USA.
-
Product
Winding Resistance Meter 50Amps, 2 Channels Rack
WR50-12R
-
Raytech Digital Winding Resistance meter WR50-12R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Wind Tunnel Control System
WTCS
-
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
Product
Transformer Winding Resistance Meters
TWA Standard Series
-
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
Product
Transformer Winding Resistance Meters
TWA Advanced Series
-
The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.
-
Product
Ohmmeter
PDRM-1A
-
The PDRM-1A ohmmeter is very accurate for measuring low resistances. You can measure values from 1µΩ to 200Ω. For this reason, it allows a wide variety of measurements to be made with a single instrument.
-
Product
Winding Resistance Tester with Demagnetisation Circuit
WRT-10D
-
The WRT-10D is a high performance winding resistance tester designed for power transformer and large motor applications. It is equipped with a bright LCD display, a rugged high quality cable set, a built-in printer, a full QWERTY keypad and a demagnetisation circuit.
-
Product
Wind Power Solution
NXA SIEMENS
-
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Portable Ohmmeters
-
Our portable digital ohmmeters offer true portability without any sacrifice to accuracy or functionality. These ruggedly constructed instruments are ideal for use in the workshop, field or test facilities.
-
Product
Winding Resistance Meter 50Amps, 3 Channels Rack
WR50-13R
-
Raytech Digital Winding Resistance meter WR50-13R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
-
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
Product
Remote Sensing Wind Measurement Device
WINDCUBE
-
WINDCUBE is a remote sensing wind measurement device that uses pulsed Doppler Lidar technology to provide high quality data on par with an IEC calibrated met mast. Introduced to the market by LEOSPHERE, WINDCUBE has quickly become recognized as the market standard for superior performance for both wind resource assessment and wind farm performance monitoring. Lenders have readily adopted data provided by WINDCUBE and consider this device to be “best-in-class.” WINDCUBE is categorized as being in Stage 3 of DNV GL’s rigorous standards related to remote sensor acceptance for formal energy assessment purposes.
-
Product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
-
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
