Inspection
check and evaluate to a quality control value.
See Also: Inspection Systems, Inspection Services
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Defect Inspection System
NovusEdge
-
The NovusEdge System provides high sensitivity inspection for the edge and backside of bare unpatterned wafers for current and advanced nodes. Multiple modules can be configured on the same automation platform for increased throughput while maintaining a small footprint for an improved cost of ownership.
-
Product
3D Inspection Service
-
The reference data may come in the form of a table, with values at specific points or features, a cad model, or 3d scan. 3D inspection services may require datum measurements, where the part to be inspected is located in a fixture that is specifically designed to orient the part by an ordered method. In some cases, the part may have features that are designed specifically to be referenced by datums, if no functional feature of the part provides a clear reference.
-
Product
Optical Inspection System
OIS Products
-
A manual optical inspection system that is able to inspect the wire-bonded leadframe or substrate.
-
Product
Dual Illumination Inspection Scope
0700-7950
-
KITCO Fiber Optics introduces our new 200X dual illumination inspection scope.
-
Product
Vison Inspection System
-
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
Product
Highly Integrated Optical Inspection
BOA
-
BOA is a highly integrated optical inspection tool for controlling quality and increasing productivity. It comprises all the elements of an industrial machine vision system in a tiny smart camera style package.
-
Product
GPR System for Concrete Inspection
StructureScan™ Mini
-
Geophysical Survey Systems, Inc.
The StructureScan Mini safely locates metallic and non-metallic targets within concrete structures up to a depth of 20 inches. The system incorporates an auto target feature that marks the detection of features of interest. This function also estimates the depth of targets and automatically adjusts the depth scale.
-
Product
Powder Coating Inspection Kit
-
Elcometer has produced this kit to enable the inspection of powder coatings on all surfaces. For a smooth surface, the digital Elcometer 415 Paint and Powder Gauge may be used but for more demanding, uneven surfaces, the Elcometer 1542 Cross Hatch Adhesion Tester is included.
-
Product
Inspection Assist Software
-
RVI software is a must for streamlining your inspection processes and improving overall efficiency. Olympus inspection assist software provides support throughout the entire process, whether streamlining on-site inspections or assisting with remote report generation.
-
Product
Test & Inspection
-
Our test and inspection products support maintenance, product quality testing, diagnostics, and quality control. The extensive range of products covers almost any application need you to have.
-
Product
Lab Inspection & Testing Services
-
Our lab services use advanced techniques to thoroughly inspect components for manufacturing flaws before assembly. We work with clients in the aerospace, automotive, oil & gas, manufacturing, wind energy, and various other industries to ensure their materials and components are free from defects that were introduced in forging or manufacturing processes.
-
Product
3D Digital Inspection
-
Digital stereo 3D imaging is a unique, advanced, stereo image presentation system designed to provide fully interactive real time natural 3D viewing and visualisation with outstanding depth perception.
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
Inspection Microscope
Z-NIR
-
The McBain Z-NIR Near Infrared Inspection System is best-in-class for wafer-to-wafer and die-to-die alignment measurement and verification. This unique tool has been sold into many industries with various applications including sub-surface wafer and die inspection for cracks and bond integrity, MEMS, wafer bonding, 3-D chip stacking, failure analysis, process development, tool verification, part characterization, environmental testing and more.
-
Product
Inspection Kits
-
Elcometer offers one of the widest ranges of inspection equipment available. Our products are used across numerous industry sectors. In all cases, there is always a need to undertake a number of specific inspections during quality control assessments - as one parameter can affect another.
-
Product
Vacuum Inspection
INDEC
-
INDEC vacuum test systems monitor a wide range of containers during the production process, including bottles, jars and cans, by measuring the cap panel concavity of their closures which is dependent on the vacuum inside. This non-contact inspection reliably identifies defective containers for automatic rejection.
-
Product
Cleanliness Inspection System / Microscope
CIX90
-
The OLYMPUS CIX90 technical cleanliness inspection system is a dedicated, turnkey solution for manufacturers who maintain high quality standards for the cleanliness of manufactured components. The OLYMPUS CIX90 system makes it easy to quickly acquire, process, and document technical cleanliness inspection data to comply with international standards. The system is intuitively designed to guide users through each step of the process so that even novice inspectors can acquire important cleanliness data quickly and easily.
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
Video Inspection Probe
-
With today's high data rates and high definition services, connector quality and inspection has never been so important. Research reveals that up to 75% of all optical network failures are attributed to poor connector quality - reduce your installation time and ensure your network is reaching its full potential.The Video Inspection Probe (VIP) application for Anritsu field testing platforms gives operators a safe, easy way to analyze and document connector conditions.
-
Product
X-Ray Inspection System
MXI Quadra 5
-
Quadra™ 5 is the X-ray inspection system of choice for sub micron applications such as PCB and semiconductor package inspection, counterfeit component screening and finished goods quality control.
-
Product
Digital Inspection Kits
-
Ideal for ‘paperless’ quality assurance systems the kits come complete with ElcoMaster® Data Management Software for professional reporting and analysis.
-
Product
Magnetic Particle Inspection
-
Is an inspection method used to identify defects on the surface of ferromagnetic materials by running a magnetic current through it.
-
Product
Wireless Fiber Inspection Probe
OCI-20BN-W
-
OCI-20BN-W is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.OCI-20BN-W offers excellent viewing on connector/fiber end-face and is able to feature to record and save image/video of fiber end-face; It can be connected to PC or phone by WIFI.More than 40 assorted high-precision tips designed for inspection solutionsAngled/Lengthened tips for awkward positions.Connect smart phone for testing FiberEye2 is the application on an android or IOS smart phone to capture, display and record the fiber end-face image from the Wi-Fi probe.Connect tablet/laptop for testing EFD is the analysis software on Windows tablet/laptop to have dusts, and scratches on end face inspected, analyzed, compiled and reported
-
Product
Visual Visual Inspection Device
IP-3000
-
Our visual visual inspection device Inspection Pro IP-3000 is an inspection device that quickly and accurately inspects the mounting board, which is constantly evolving, and judge whether it is good or bad without omission.
-
Product
Analog Ultrasonic Inspection System
ULTRAPROBE 100
-
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
Product
HD Inspection System
vCam-6
-
The vCam-6 HD inspection system from Vivax-Metrotech gives you the flexibility to cover a range of inspections including municipal collection systems, residential plumbing, indoor commercial lines, and lateral lines from three inches up to eight inches in diameter. Our camera systems use the latest technology packaged in a rugged, lightweight, compact profile made specifically for the harsh conditions related to sewer lateral inspections. All Vivax-Metrotech camera systems are backed up by a full one-year warranty, on-site training, and local support through our dealer network.
-
Product
Defect Inspection and Review
-
KLA’s defect inspection and review systems cover the full range of yield applications within the chip and wafer manufacturing environments, including incoming process tool qualification, wafer qualification, research and development, and tool, process and line monitoring. Patterned and unpatterned wafer defect inspection and review systems find, identify and classify particles and pattern defects on the front surface, back surface and edge of the wafer. This information allows engineers to detect, resolve and monitor critical yield excursions, resulting in faster yield ramp and higher production yield.
-
Product
Inspection System
Pixie
-
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
-
Product
X-Ray Inspection
MXI Jade Plus
-
Restrictions in manufacturing materials and ever increasing expectations for reliability mean ensuring quality product manufacture is more important than ever. Jade Plus enables you to Prove Your Quality and reduce product returns from the field, and the associated cost and damage to reputation.
