Electronics Test
Devices whose quality of operation is based on the effects of electrons.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
LCR Meters
-
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
Product
PRODUCTION TESTING
-
The Production Test Department is a component of the Engineering Department where production test technicians perform routine factory testing in accordance with approved test procedures. Most of the electronic testing is automated, whether ambient acceptance testing or environmental ESS testing.
-
Product
Adapter/Stainless Steel
WADP-24FSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
Flexible Temperature Testing & Thermal Cycling
TA-5000B Series
-
MPI Thermal manufactures a variety of compact temperature chamber solutions for electronics and material test and thermal conditioning. An array of standard and custom design high-performance Clamshell styles and other configurations and custom dimensions and sizes are available. MPI ThermalAir Systems compact chamber thermal products are available to meet your test application needs.
-
Product
Straight Wire Porbe Pins
Buckling Beam
-
Straight wire probe pins are a proven solution for various electronics production test environments.
-
Product
Vertically Falling Water Drops Device IPX1/2
IEC60529
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005.Satisfying requirements of level IPX1/2. Applide to test LED lamps and house hold appliances, and other electric and electronic products waterproof test of IP code level IPX 1/2.
-
Product
Test Probes
-
A physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
EMC Testing
-
D.L.S. Electronic Systems, Inc
EMC testing and consulting services to the Electronics, Medical Equipment, Automotive, Aerospace, Computer, Telecommunications, and other industries. We are a NVLAP certified test facility, capable of testing electronic equipment to today's high frequency requirements. Our 14 Test chambers and 3 Open Area Test Sites can perform full scan Immunity and Emission testing at frequencies up to 40 GHz. Please contact us for your specific requirements.
-
Product
Industrial Electronic Endoscope
-
Xiamen IDEA Electronic Technology Co., Ltd.
1.Railway Electronic Industrial Endoscope testing.2.Large screen color screen to restore the true image. 3.Industrial endoscope.
-
Product
Adapter/Nickel
WADP-NMSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Termination
WTER-6N2
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Test Probe
-
Beijing KeHuan Century EMC Technology Co,.LTD
Is a physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
-
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
Product
Electronic Test Instruments
-
We offer all types of electronic test equipment for the design, troubleshooting and repair of products and devices. Our handheld, bench, fixed and portable equipment covers virtually every electronic testing application. You can capture measurements, verify performance and conduct analysis with oscilloscopes, spectrum analyzers, decade boxes, bridges and other instruments. With one LCR meter, measure inductance, capacitance and resistance. Our frequency counters and function generators give you professional RF test equipment performance. Manufacturers such as Fluke, Keysight Technologies, Rigol and B&K Precision, provide proven technologies and innovation within our electronic instrument category.
-
Product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
-
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
Product
Automated Test and Programming Station
The Scorpion BRiZ
-
The primary goal of an electronic test strategy is to achieve the highest possible test coverage. Often, a combination of test tools and techniques needs to be integrated in order to meet this challenge. A decisive factor in selecting the optimal test strategy is cost. So, choosing a test platform that results in the highest test coverage for your investment is essential.But, what if in addition to test, you require in-system or on-board programming? What would be the best way to handle this while staying within budget and meeting production timelines?
-
Product
EFT Module for Teststand
-
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
Custom Magnetic Recording Heads
-
International Electro-Magnetics, Inc.
We have manufactured over 5,000 different head designs. If we don't have one to suit your requirements, we will design and build to your specification. Our toolroom is well equipped to produce precision parts, and our design projects have included flux sensing systems, magnetic disk encoding, and electronic test equipment.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
SMA Rotary Attenuator
WATT-6SR1211
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Multiplexers
-
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
-
Product
Electrostatic Discharge Generator
STT-ESD-2005
-
Beijing KeHuan Century EMC Technology Co,.LTD
The STT-ESD-2005 ESD generator meets the requirements of IEC61000-4-2 and GB/T17626.2. Its maximum ESD voltage reaches 30kV, meeting the standard's ESD voltage requirements (Level 4 air-gap discharge requires 15kV). It is also suitable for a wider range of applications and future standards. Therefore, the ESD-2005 ESD generator can be used for ESD testing of most electrical and electronic equipment, ensuring test comparability and reproducibility.
-
Product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
-
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
Product
Adapter/Stainless Steel
WADP-24F29F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Automatic Test System
-
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
Power Cable Fault Locator
TM500
-
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
Product
Multifunction Handheld SM MM OTDR
X2100
-
X-2100 series OTDR is manufactured with patience and carefulness, following the nationalstandards to combine the rich experience and modern technology, subject tostringent mechanical, electronic and optical testing and quality assurance; inthe other way, the new design makes X-2100 more smart and compact andmulti-purpose. Whether you want to detect link layer in the constructionand installation of optical network or proceed efficient maintenance andtrouble shooting, X-2100 can be your best assistant.
