Phasing
See Also: Phase, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Sticks, Phasors
-
Product
Digital Phase Meters
-
Digital Phase Volt-Ampere Meter is a well-developed full-automatic, multi-functional, digital, intelligent meter specifically designed for field testing, which is a overall upgrade product based on mechanical knob phase volt-ampere meter, can simplify operation and reduce the possibility of misoperation, featuring high accuracy, high stability, low power consumption, easiness to use and so on.
-
Product
Transformer Ratio Meters
Handheld Turns Ratio & Winding Resistance Tester TWR-H
-
TWR-H is a handheld, battery operated, fully automatic test set specially designed for turns ratio, phase shift, excitation current and winding resistance measurements of transformers. It can also perform demagnetization of these transformers. Transformer turns ratio is determined by applying AC voltage across high voltage winding, accurately measuring AC voltage across the corresponding unloaded transformer winding, and then displaying the ratio of these voltages. User can enter a transformer’s nameplate voltages, so that turns ratio deviation can be calculated. This feature eliminates any error otherwise caused by an operator’s manual calculation. TWR-H compares measured turns ratio with the nameplate ratio and prints out the % of error for each test. Transformer winding resistance is determined by injecting DC current through a winding, accurately measuring DC voltage across the winding, and then calculating resistance as the ratio of voltage and current. The device generates true DC ripple-free currents. Both the injection of the current and the discharge of energy from transformer magnetic circuit are automatically regulated.
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
Product
Multifunctional Meter
CPM-10
-
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
Product
Phase Noise Analyzers
-
The phase noise analyzer portfolio from Rohde & Schwarz offers an affordable, mid-range solution with high sensitivity and fast measurements as well as high-end ultra-high-sensitivity solutions with advanced measurements modes. Ideal for phase noise analysis and VCO tests, the industry-leading solutions enable two-path phase noise analysis with real-time cross correlation and fast VCO characterization with built-in low-noise DC sources. Additionally, high-end signal and spectrum analysis can be added into a single box.
-
Product
Vector Finders with InternalAttenuators
VF-145 LA AND VF-145 LMA
-
The VF-145 LA and LMA models are functionally the same as the VF-145 L and LM on both electrical performance and mechanical specifications. However, the LA and LMA models include an internal PIN diode attenuator that provides up to 12 dB of attenuation (measured at 150 MHz, attenuation decrease slightly as operating frequency increases) to the incoming radio signal. This attenuation occurs after the signal is received by the unit and phase shifted for processing, but before it is placed on the coax feedline to the receiver. In addition, the PIN diode utilized will absorb short burst of RF should transceivers be keyed accidentally by the user. This feature aids in very strong signal DF operations but will not totally guarantee against system overload under very strong RF emissions.
-
Product
Multifunctional testers
MI 3100 SE EurotestEASI
-
MI 3100 SE EurotestEASI is a fast, accurate and easy to use multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. Besides, the MI 3100 SE EurotestEASI enables on-line voltage monitoring, phase sequence testing and earth resistance measurement. EurotestEASI is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
Product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
-
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
Product
Phase Angle Voltmeter
PAV1010A
-
Measuring Vrms, inphase, quadrature, freq, ratios and phase angles. Using Discrete Fourier Transform algorithms, the PAV1010A provides capability, performance and versatility not available with traditional PAVs. Targeted at the Synchro/Resolver and LVDT/RVDT marketplace, this instrument makes measurements of Phase Angle, In-Phase, Quadrature (90° component), Fundamental and Total Vrms very straightforward. All these measurements are displayed simultaneously on a bright multifunction display.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
SNMP Agent Testing & Debugging Suite
SNMP Inquistor
-
An SNMP Agent Development process inevitably involves testing and debugging activities that are tedious and time consuming. To save time and money on this development phase and to ensure that the developed responder's software is compliant with the SNMP standards, LogiSoft AR Ltd. came up with the SNMP Inquisitor, an easy to use, intuitive and comprehensive application suite that includes: MIB Compiler, SNMP Inquisitor Application and SNMP Sender Utility.
-
Product
Precision Condenser Microphone
377C10
-
Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%
-
Product
Measuring and Monitoring Relays
-
Various measuring and monitoring relays are available for the purpose of monitoring electrical quantities. In addition to overvoltage, undervoltage, frequency, unbalance, phase sequence, phase failure and loop monitoring, special solutions for specific applications are also possible: extended temperature ranges, sector-specific standards, compact design, country-specific profiles.
-
Product
Near Field Probes 30 MHz - 6 GHz
XF Family
-
The XF family consists of 4 passive magnetic field probes and 3 passive E field probes designed for measuring magnetic and E-fields in ranges from 30 MHz to 6 GHz during the development phase. Due to their integrated impendance matching the probes are less sensitive in the lower frequency range than the RF type probes.
-
Product
Sweating Thermal Guarded Hotplate
-
Sataton Instruments Technology CO., Ltd
Sweating guarded hotplate is the textile testing instrument for measuring of thermal and water-vapour resistance properties under steady-state conditions. By testing the thermal resistance and water-vapour resistance of textile materials, the tester provides a direct data for characterizing the textiles’ physiological comfort which involve a complex combination of heat and mass transfer. The hotplate is intended to simulate the heat and mass transfer processes which occur next to human skin and measure the hence transport properties in a steady-state conditions involving combinations of temperature relative humidity, air speed, and in liquid or gaseous phase.
-
Product
Electronics
-
Flann provides control processors and switch drivers that support all Flanns current range of programmable attenuators, phase changers and waveguide switches
-
Product
Harmonic Clam Meter
-
TES Electrical Electronic Corp.
Analysis for 3p4W, 3P3W, 1P2W, 1P3W. True RMS VAlue. Active Pwer. Apparent and reactive pwer. Power FActor, Phase angle.
-
Product
Common Mode Chokes
-
Common Mode Chokes, as the name implies, are designed to attenuate and filter common mode noise within an electric system. The key parameters for a common mode choke are the current rating (to ensure the part does not overheat within the application), the impedance versus frequency (to ensure it is optimized to attenuate the desired frequencies), the isolation voltage (to ensure it meets board level requirements between the line and neutral phases) and safety isolation (to ensure it meets the safety requirements of the end-application). It is important to remember that common mode chokes cannot saturate in the application (under normal use) as they are designed to ensure that the line and return currents are balanced.
-
Product
MXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5181B
Signal Generator
Take your devices & designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading output powerThoroughly test receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
Product
Phantom Vent Tube Metal Detector
-
The Phantom Vent Tube metal detector is primarily designed to detect and track a fallen vent tube nozzle inside a bottle that is conveyed through bottle-processing equipment. The convenient retrofit design allows for easy installation into existing bottling lines. Built from stainless steel (304) material and totally enclosed for washdown purposes, the detector phases out the conveyor belt and maintains a steady sensitivity.
-
Product
Gain-Compression Measurements
S96086B
-
The S96086B, gain compression measurements provides fast and accurate characterization of input power, output power, gain, and phase at the compression point of an amplifier, over a specified frequency and power range, with a simple setup
-
Product
Hand-held 3-Phase Meter Tester
6 Series
-
Powermetrix extends its revolutionary line of handheld three phase analyzers with the PowerMaster® 6 Series, now with Powermetrix Remote Manager (PRM)®. PRM enables wireless control of essential and various metering site accuracy tests contained within the PowerMaster 6 Series.
-
Product
Single Phase Energy Meter Test Bench Type KP-S1000-A
-
Bofa Instrument & Equipment Co., Ltd
Single phase test bench, type KP-S1000-A, is a new generation, high precision energy meter calibration equipment. It can test mechanical energy meter and electronic energy meter, in spite of open or closed test link (I-P link). It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
MICROWAVE SWITCHING DIODES FROM 1 to 40 GHz
-
Insight Product Company offers Microwave Switching Diodes with switching time up to 3 nsec and operating in frequency range from 1 to 40 GHz. The p+ -n - n+ silicon spackage-less switching diodes are designed to be used in microwave switching devices, phase changers, modulators, microwave attenuators - parts of hybrid microcircuits that provide capsulation and protection against ambient action.
-
Product
2.5G DPSK Demodulator
-
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Product
Meter Test System
MTS-100
-
Kongter Test & Measurement Co., Limited
This Meter Test System features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 120A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Safety
-
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
65 GSa/s Arbitrary Waveform Generator
M8195A
Arbitrary Waveform Generator
Sample rate up to 65 GSa/s High channel density: 1, 2 or 4 channels per module, synchronization of up to 16 channels on 4 modules with the M8197A multi-channel synchronization module Built-in frequency and phase response calibration Embedded DSP enables real-time waveform and impairment generation(in conjunction with the 81195A optical modulation generator software)
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
