DC Shunts
A resistor which delivers a millivolt of DC output in proportion to the current flowing through the resistor.
-
Product
AC & DC Aging Test Equipment for Arrester Valve Plate
-
Shanghai Guantu Technology Co., Ltd.
The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
Switch Module
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
Product
DC Voltage & Current Data Logger
-
The Track-It™ DC Voltage and Current Data Loggers are two channel battery powered stand alone compact data loggers that record up to 32,000 samples each of DC Voltage or Current data. Units are available in 4 DC voltage ranges or for DC current. Simply plug the data logger into an available USB port on your PC and customize the settings or transfer data with the included Track-It Software program.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
DC Power Supplies
ASD FLX Series
-
AMETEK Programmable Power, Inc.
The ASD FLX gets its name from its modular design with front loading modules for easy access and flexible voltage options. The chassis with removable, lightweight modules allows for easy one person installation. Furthermore, this product has a wide range of voltage input, 324 VAC to 528 VAC, giving it the flexibility to be utilized globally in a single configuration.
-
Product
DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
Programmable DC Electronic Loads (conventional and regenerative)
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
-
Product
DC Block Power Splitter Combiner
PD5130
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsRoHS Compliant Splitter Construction
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Adapter, 2.4 mm (m) to 2.4 mm (m), DC to 50 GHz
11900A
-
The Keysight 11900A is a metrology-grade, 2.4 mm male to 2.4 mm male adapter with dc to 50 GHz operation.
-
Product
Adapter, 1.0 mm (m) to 1.0 mm (m), DC to 110 GHz
11920A
Coax Adapter
The Keysight 11920A precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 110 GHz.
-
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
DC System Power Supply, 600 V, 1.3 A, 780 W
N5752A
Power Supply
The single output, 780 W N5752A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
DC Magnetic Flux Leakage Testing
ROTOMAT / TRANSOMAT Product Family
-
Foerster Instruments, Incorporated
With the new generation ROTOMAT DA and TRANSOMAT DA flux leakage test systems FOERSTER is setting new standards in continuous quality assurance of ferromagnetic steel tubes. The test systems enable the reliable detection of natural and oblique defects, regardless of their angle or length, in addition to standardized longitudinal and transversal defects. The miniaturization of sensors together with highly integrated electronic components dramatically increases the number of channels. This makes a more precise and finer scan of the surface possible, giving a more complete set of information regarding detected defects. The newly introduced C-Scan visualizes these defects in high-definition and real-time, resulting in a completely new evaluation of the tubes to meet rising quality requirements.
-
Product
Programmable High Power DC Power Supply
ADG series
-
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
Product
Coaxial Fixed Attenuator, DC to 26.5 GHz
8493C
Attenuator
The Keysight 8493C coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator has APC-3.5 connectors and is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 40 dB.This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
-
Product
600 Watt DC Electronic Load Mainframe
N3301A
Mainframe
The Keysight N3301A is a half-rack width mainframe with 2-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3301A holds up to two N3302A, N3303A, N3304A, and N3307A load modules, or one N3305A and N3306A load modules, allowing up to 600 watts of total maximum power.
-
Product
DC Power Supply
CSP-3
-
● Universal power AC90~264V/DC127~380V● Build in power factor control circuit in high power model(120W~500W)● Available for series and parallel operation● To be a Back up power function with relay output in option( not available in model 20W and 24W)● RoHS & UL version in option● DIN rail mounting
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8493B
Attenuator
The Keysight 8493B coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Cable Assembly, Type-N (m) to Type-N (m), DC to 6.0 GHz
11500B
Cable Assembly
The Keysight 11500B is a 58 cm (23 in) type-N male to type-N male cable assembly with a frequency range of DC to 6.0 GHz.
-
Product
DC Electronic Load, Single-Input: 150V, 40A, 250W
EL33133A
-
The Keysight EL33133A bench DC electronic load provides a single input and a built-in data logger. Provide static or dynamic load test up to 40 A and 150 V. Display results in a meter view or over time using the built-in data logger.
-
Product
DC Josephson Voltage Standard
-
The system enables a number of calibration and measurement functions for dc voltages:*Calibration of secondary standards*Calibration of linearities and accuracies of dc voltmeters in the measuring range from 0 to ± 10 V.*Extremely exact output of any reference voltages*Direct comparison of two voltage standard measuring systemsNo other measuring system in the world offers such a variety with the highest precision.
-
Product
DC Power Supplies
SFA Series
-
AMETEK Programmable Power, Inc.
The SFA family builds on the industry leading Sorensen SGA series to provide a high power current source for laser diode applications. State of the art high power laser diodes require well-regulated current control to avoid catastrophic damage. Under anomalous operating conditions, excessive stored energy in the output circuit of the power supply can result in peak stresses that can permanently damage the device. Providing a constant current regulation mode only, the SFA’s low stored energy output minimizes damage potential for sensitive devices as well as enabling a current slew rate of up to 400 A/msec.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
DC to 100MHz
1394A
-
Nominal Heater Current: 5 mA rms,Max. Heater Current: 7.5 mA rmsCouple Output: 7 mV ± 12% at nominal heater current.Couple Resistance: 8 W ± 20%.Maximum DC Reversal Error: ± 0.04%Couple Output Voltage to Heater (ground): ± 50 V (dc + acpk-pk) max.
