Static Locators
Measure static electricity charges.
-
Product
Inductive Tone and Probe Cable Locator Kit
72-8500
-
This tone & probe set is a basic necessity for anyone running data, voice or any other low voltage cable. It is also suitable for tracing alarm, coax or speaker cables which are already installed.
-
Product
Single Location Platform for Every Connected Thing
ReachPoint
-
Unleash the freedom to explore with geolocation and indoor navigation from anywhere in the world in real time. Provide live location updates powered by an all-in-one cloud-based platform with enhanced capabilities and technology for greater efficiency and improved battery consumption.
-
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Wire Tracers & Underground Locators
-
When you want to make absolutely sure you’re digging in the right place, depend on the technology leader: Amprobe. Known for speed, reliability, and accuracy, Amprobe Wire Tracers and Underground Locators will help you get your job done efficiently. Whether you’re looking for a wire (energized or de-energized) in a wall or ceiling, or want to locate buried utilities before you dig, you can depend on Amprobe’s best tracers to help you get the job done quickly.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Truck Mounted Static Grounding Verification
Earth-Rite MGV
-
The Earth-Rite Mobile Ground Verification system (MGV) is a unique, patented technology designed to provide automatic confirmation of a positive electrostatic ground connection for trucks collecting and transferring flammable / combustible products.
-
Product
Mobile Cable Fault Location System
BAUR Syscompact 4000
-
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
Product
Single-Phase Static Switches
ISSF "PLUS"
-
The solid state switches ISSF “PLUS" exceed the limitations of electromechanical switches for many difficult and demanding applications, such as the control of high power motors, transformers, tungsten lamps, heating elements, electric furnaces, etc.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Visual Fault Locators
-
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
Product
Static Remover (Ionizer)
STABLO-AP
-
STABLO-AP provides reliable measurement by removing static electricity.
-
Product
Pen-type Visual Fault Locator (VFL)
JW3105P
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
The JW3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:
-
Product
Three Phase Multifunction Static kWh Meter
SY 1065
-
Hong Kong Songyang Industrial Ltd.
This kind of meter integrates many functions into one, realizes the functions of time-sharing electricity measurement for active double-direction, measuring demand, sinusoidal reactive, calculating power factor, displaying and tele-transmitting present voltage, current, power and load curve etc. and it realizes the function of recording all the missing voltage, missing current and the percent of pass for voltage,
-
Product
Static Tester
DRK151
-
Shandong Drick Instruments Co., Ltd.
The tester is applicable in testing the surface potential and the properties of anti-static products .This tester applies to test electrostatic voltage of charged object such as conductor, insulator, and the human body.
-
Product
Cable Locator
CL 20
-
Cable fault location with the BAUR CL 20. The CL 20 cable locator comprising a transmitter and a receiver is used to determine the exact location of cables and metal pipes. The ability to determine laying depths of up to 4.5 m and to measure signal currents at the touch of a button allows you to obtain reliable information on the position of the cable within the shortest time.* Fast and exact location of position and laying depth of cables* Intuitive operation – no special measurement knowledge required* Lightweight and manageable
-
Product
Pitot Static Test & RVSM Air Data Accs Kits
ADA320-723
-
Kit Model ADA320-723 (Bar type) contains the equipment required to connect the Air Data Tester to the pitot and static ports, for the performance of a complete test of the main and alternate Air Data System of the Airbus Industries A-319, A-320, A-321 aircraft. The equipment is approved by Airbus Industries.
-
Product
Ocean Signal RescueME PLB1 (Personal Locator Beacon)
RescueME PLB1
-
The RescueME PLB1 is the world's smallest 406mhz & GPS enabled PLBOperation of the rescueME PLB could not be simpler. To activate the PLB: Pull the retractable antenna out by its end tab, flip open the spring loaded cover over the activation button, hold the button for 1 second until the lights blink. Visual instructions are clearly printed on the case. When activated, the rescueME PLB1 will transmit accurate position data from its 66 channel GPS for a minimum of 24 hours while the integrated strobe light ensures maximum visibility.Ocean Signal has ensured that rescueME, like all of its other safety products, exceeds statutory requirements. RescueME PLB provides an incredible 7 year battery life, and is covered by a 7 year warranty. Even after more than 24 hours of continuous operation, and when the battery power is insufficient to transmit the satellite signal, the PLB1's homing beacon and strobe light will continue to operate. This high intensity strobe light features a molded lens to enhance the visibility of its efficient LED and it gives a powerful 1 candela light emission.Self-test of the PLB can be carried out with a simple button press with the start of test and results clearly indicated by a green flashing light. The antenna is easily extended like a normal tape measure and can be retracted using the winding mechanism on the top of the unit. This unique feature greatly facilitates user training and familiarization as it is not a one time deployable antenna similar to existing PLBs.rescueME comes with a snap-in mounting bracket and universal rubber mounting strap which can be fitted permanently or with each use. It is also supplied with a detachable flotation lanyard to accommodate all scenarios out of the box.
-
Product
Pen Style Visual Fault Locator
CARY-VFLXX
-
The CAWI-VFLxx Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network duringand after installation.
-
Product
Static Grounding Protection for Process Plant & Equipment
Earth-Rite PLUS
-
Precision and reliability is what the Earth-Rite PLUS provides to HAZMAT professionals and engineers who are tasked with protecting personnel and plant assets from the ignition hazards of static electricity during tank car, LACT & skid unit and tote loading/unloading operations.
-
Product
Visual Fault Locators
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Visual Fault Locators
-
-
Product
Cable Locator (LCD type)
5500 CB
-
Standard Electric Works Co., Ltd
● The 5500 CB transmitter is a great tool for locating and identifying cables and individual conductors. ● Designed for locating unenergized cables and powered cables. ● Voltage measurement for cables : ACV 12V~300V DCV 12V~300V ● Signal Transmission • Transmission Power Level Selection (includes 1, 2, 3) • Transmission Signal Code Selection (includes F, E, H, d, L, C, O, A) ● Flashlight & Back Light function.● The Silent Mode (Disable Button Beep).● The Level Bar Display on the LCD Screen (the transmission power level indication).● The Action Wave Display on the LCD Screen (when the signal is transmitted).● Auto power off function.
-
Product
Cable Fault Location System
Syscompact 2000 M Pro
-
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
Product
Static & Lighting Chokes
-
Lighting chokes are used to pass tower lighting voltages across the base insulator of a series-fed tower without appreciably altering the tower impedance. LBA TC-300 general purpose tower lighting chokes are provided for three wire 110/220 VAC circuits. Maximum current is 25 amps. These chokes are rated for peak base voltages to 10,000 volts, and present a typical reactance of +j5000 ohms at 530 kHz. Bypass capacitors are provided on each winding.
-
Product
Pipe Locator
AML PRO
-
The All-New AML PRO™ is a scientific instrument that utilizes ultra-high radio frequencies to find differences in densities. This offers the best method for locating PVC & PE pipes and nearly any other object that has an edge.
-
Product
Industry Standard in GPR for Utility Mapping and Locating
GSSI’s Utility Scan Pro GPR
-
Geophysical Survey Systems, Inc.
With UtilityScan Pro, users can quickly identify and mark the position and depth of metallic and non-metallic objects; including utilities such as gas, communications and sewer lines as well as underground storage tanks and PVC pipes. Based on the SIR 4000 controller, the UtilityScan Pro provides the GPR professional with solutions to any underground locating situation.
-
Product
Static Design Verification
ALINT-PRO
-
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
-
Product
Pitot Static Tester
ADSE 643
-
The ADSE 643 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fixed and rotary wing.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The ease of use and portability enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.The test set is housed in an anodized metal and rugged case.An attached case contains the pressure hoses and electrical cables.
-
Product
Visual Fault Locator
TW3105
-
Techwin(China) Industry Co., Ltd
Pen Type is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network.
