Current Detectors
-
Product
EBSD Detector
e–FlashFS
-
The new EBSD detector e–FlashFS has been designed for maximum sensitivity to allow highspeed EBSD measurements without compromising data quality – even on challenging applications like deformed or lightweight materials. To further improve the pattern quality, the cooling system of the e–FlashFS has been upgraded to lower its functioning temperature and therefore reduce the dark current of the CCD camera as much as possible.
-
Product
Remote Spectral Detector
CSS-45
-
The CSS-45 detector incorporates a powerful microprocessor which performs not only data acquisition but also all necessary lighting calculations. Both USB 2.0 and RS 485 interfaces are standard enabling the flexible configuration of single and multi-detector based systems. An optional software development kit supports integration into third party application software. With its wide spectral range from 360 nm to 830 nm the CSS-45 is ideal, for example, as a high accuracy photometric and colorimetric detector (according to CIE S023).
-
-
Product
CO Detectors
-
UEi Test & Measurement Instruments
A device that detects the presence of the carbon monoxide (CO) gas to prevent carbon monoxide poisoning.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
Safety Voltage Detector
325 SVD
-
Standard Electric Works Co., Ltd
Compact, easy to wear and convenient in use. Designed for indoor and outdoor use. Water-proof design. (IP65). Equipped with self-testing functions. Able to sense all kinds of AC High Voltage System. Low power consumption. CE Certified right LED visual indication.
-
Product
Solid State Gas Detectors
SMC 20X/200X
-
The SMC 20X/200X are single-gas detectors used to monitor combustible gas, hydrogen sulfide (H2S) or carbon monoxide (CO). The detectors are based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas.
-
Product
Leakage Current Monitor
LCM500
-
The Doble LCM500 Leakage Current Monitor can measure condition while a surge arrester is still in service, measuring the quality of the metal oxide blocks and helping manage the risk of failure.
-
Product
Ultrasonic Leak Detector
VPX-WR
-
The Superior AccuTrak Model VPX-WR represents THE state-of-the-art technology for ultrasonic air leak detection! This ultra-durable and waterproof instrument incorporates our patented and trademarked circuitry we call "DND" (Dynamic Noise Discrimination). Older detectors using only the heterodyne technique, simply cannot offer the same leak detection abilities, especially in loud plant environments.
-
Product
Leakage Current Sensors / Small Current Sensors
-
ChenYang Technologies GmbH & Co. KG
This current sensor is based on magnetic modulation and compensation principle, and can beused for measurement of small DC current and leakage current, current difference between two ormore conductors.
-
Product
Open Path Gas Detector
Senscient ELDS
-
The Senscient ELDS laser-based open path gas detector is available for a wide range of toxic and flammable gases.
-
Product
Non - Contact Voltage Detector
Model 273 HP
-
Kusam Electrical Industries Limited
The 273 HP is a Non-contact voltage detector. It has two ranges for selection.The 273 HP consists of an internal pickup sensor, a function selection switch, a visual and a sound annunciator. With the 273 HP, physical contact with electrical conductors is not necessary when testing for live lines. Its sensor senses the radiated field which surrounds live conductors. Radiated field strength increases with voltage and decreases quickly with distance or earth shielding
-
Product
Zero Bias Schottky Detectors
-
KRYTAR Zero Bias Schottky Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
Magnetism Detector DET
432
-
The MAC Magnetism Detector is widely used by steel suppliers and fabricators to determine residual magnetism in iron and steel objects.
-
Product
Low Noise Current Preamplifier
SR570
-
Stanford Research Systems, Inc.
The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.
-
Product
Coaxial Power Detector
-
RF Lambda’s coaxial power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
MPI Flaw Detectors
-
A non-destructive testing method that can detect surface and subsurface flaws in ferromagnetic materials.
-
Product
Planar Doped Barrier Detectors
-
KRYTAR Planar Doped Barrier Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
Point IR Gas Detector
IR400
-
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
Product
RFI Detector Meter
MFJ-805
-
Use this ultra-sensitive pocket-sized RFI Detector to track down and eliminates RFI caused by radiating cables and wires. Usable from VLF to VHF. Gain adjustable over 50dB range.
-
Product
Freezing Rain and Ice Detectors
-
Freezing-rain and ice detectors detect the presence of icing conditions so that appropriate actions can be taken to prevent damage to power and communication lines, to warn of road hazards, to keep ice off a plane’s wings, and to prevent ice from forming on turbine blades.
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
Product
ESD Event Detector
Novx MiniPulse
-
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.
-
Product
Linear Detector Arrays (LDAs)
X-Scan H
-
This digital end-to-end solution is built on a proven concept enabling easy integration, and accelerated development time of X-ray systems. X-Scan H series has high radiation hardness extending lifetime of detectors significantly, and reducing total costs. The series is available in several standard lengths easily scalable to various configurations.
-
Product
ElectroMagnetic Detector
MP Series
-
MP-900/9000 are chiefly used in conjunction with a detector gear mounted onto a rotating shaft by bringing the detector into proximity to the gear so that the detector outputs frequency signal of which is proportional to the rotational speed. So various types are available including low-priced, general purpose, oil proof and heat resistant types that you can make a choice for your usage.Signal cables (except attached-cable types), extension cables and connectors are sold separately.
-
Product
Stealth Laboratory/QA Metal Detector
-
Stealth Laboratory metal detectors are manufactured to suit any application. Designed to be used in offline product examination to assist in determining contaminant source. Stealth detectors use digital signal processing technology and have high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Product
Pressure To Current Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
-
Product
Gas Leak Detector
Gasurveyor 500
-
Teledyne Gas & Flame Detection
The Gasurveyor 500 is the most flexible range of gas detectors available from GMI. By simple selection of hardware and software options, the instrument can be readily configured to suit your exact application. Offering highly accurate and reliable instrumentation in an extremely robust, anti-static case, the Gasurveyor 500 Series measures gases common in many applications.Any combination of flammable gas from parts per million (ppm) through Lower Explosive Limit (LEL) to percent volume, oxygen, carbon monoxide and hydrogen sulphide can be selected to ensure that your exact requirements are met. All of the Gasurveyor 500 Series are dual mode instruments, making them suitable for both surveying work and confined space.
