-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Three-Phase Smart Socket
WECO 3230
-
Utilize the RW-3X's features while on site in the van, as well as back at the shop with the WECO 3230 Three-Phase Smart Socket. The 3230 features built-in laser optics, Smart Socket™ technology and automatic meter form selection. Connect the RW-3X to the 3230 side panel using the included cables and the RW-3X Winboard Embedded software automatically sets the meter form, which will then populate on the WECO 3230 LCD display panel, and now you are ready to test. Not only does the 3230 make testing meters a snap, but it expands the current capability of the RW-3X to a full 50 amps, allowing the user to test class 320 amp meters.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5641 Series
Digital I/O
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), functional test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) which can be individually set to operate in either conversion or static I/O modes.
-
Product
PH350 Waterproof Single-Channel pH and ORP Smart Handheld Meter Kit
-
Get easy-to-read and accurate readings with auto-hold, auto-stable, and real-time measurements with stability indicators. The Environmental Express® Oakton® 300 series multiparameter meters utilize smart sensor technology with sensor heads that feature a built-in digital circuit for automatic sensor recognition. Sensor information including sensor ID, calibration data, and measurement setup is stored in sensor head and viewable on the meter display when sensor is connected. Sensor heads are easy to connect and disconnect with waterproof push-lock connector. Sensor cartridges (pH and EC) are replaceable for a cost-efficient and environmentally friendly system. Blue LED light on the sensor head functions as a reading stability indicator, flashing until the reading is stable. Meter stores up to 10,000 data sets with date-and-time stamp for accurate and easy analysis. Quickly transfer data from meter to computer seamlessly via USB cable or wirelessly via Wi-Fi. Easily take measurements and conveniently store meter and electrodes with built-in foldable stand on the back of the meter. Three grooves on the meter serve as electrode holders, to hold up to three electrodes simultaneously.
-
Product
PCI 24-Bit Digital I/O Cards
PCI-DIO-24D/H
-
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
Product
32-CH 16-Bit Up to 250 kS/s Multi-Function DAQ Cards
PCI-9114 Series
Data Acquisition Module
ADLINK PCI-9114 series are 32-CH, 16-bit, high resolution multi-function DAQ Cards. The PCI-9114 device features flexible configurations on analog input. The devices are divided into 2 kinds: normal gain version and high gain version. Both versions provide 4 programmable input ranges for bipolar and unipolar inputs. The A/D on the PCI-9114DG device features a sampling rate of 100 kS/s with resolution at 16 bits, while PCI-9114A-DG/HG device features a sampling rate of up to 250kS/s with resolution at 16 bits. The device supports automatic analog input scanning, and offers a differential mode for 8-CH analog inputs and maximum noise elimination, as well as single-ended modes for 16- CH analog inputs. The PCI-9114 also features 1-CH 16-bit general purpose timer/counter, 16-CH TTL isolated digital inputs and 16-CH TTL isolated digital outputs. ADLINK PCI-9114 delivers cost-effective and reliable data acquisition capabilities and is ideal for a broad variety of applications.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 470Ω
50-297-014
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 11.4MΩ
50-298-053
Programmable Resistor Module
The 50-298-053 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Shuttle Bus VMC Intelligent Interface Card
IIB-SB-VME
-
The Shuttle Bus VME is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, andMultiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a VMEplatform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include LDB_BCT,LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
FPGA PXI High-Performance Digital I/O Card
GX3702
Digital I/O
The GX3702 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3702 is supplied with an integral expansion board providing access to the FPGA's 160 I/Os and is pin for pin compatible with the NI PXI 7813R and 7811R FPGA cards . Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
-
Product
Transcoding Card
VEGA-3310
-
2-ch 4Kp60 or 8-ch real-time 4:2:2 10bit HEVC,AVC & MPEG-2 encode, decode & transcodeUltra-low latency supportLess than 35W power consumptionSimple-to-use API and example code for FFmpeg and GStreamer multimedia frameworks
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
Communications Module
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
Analog Output Module
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
Product
Probe Cards
Ceramic Blades
-
SV TCL offers a variety of ceramic blades and blade probe cards. We have patented ceramic microstrip blade probes available in low leakage and low capacitance for optimal signal transference, while SV TCL's blade cards are ideal for parametric and RF testing.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 62.1Ω
50-298-011
Programmable Resistor Module
The 50-298-011 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Production Parametric Probe Card
VC20TM Fab
-
*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
Modular Cards
SET 14XX
-
The carrier boards from the SET Modular Card 1415 / 1416 / 1417 series offer slots for 8 functional/measuring modules from the SET “SMARTbrick” series.
-
Product
RF Switch Cards
-
The Adapt-a-Switch® RF switch cards deliver high performance and high density for your RF switching applications.
-
Product
PCI Express Communication Card
ECU-P1522
-
2-Port SFP Base Etheret with HSR/PRP Low profile PCI Express Communication Card
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
-
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
2-Port SFP Gigabit Base Ethernet Card With HSR/PRP
ECU-P1524PE-B
-
PCIe or embedded module supporting dual 1000Mbps fiber connections, designed for high-availability networks.
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-16
-
16 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 7.6" high x 13" wide x 1" deep (193 x 330 x 25 mm).
-
Product
Serial Card
PCIe-COM232-8
-
ACCES I/O’s PCI Express multiport serial communication cards deliver eight (PCIe-COM232-8) or four (PCIe-COM232-4), high-speed, RS-232 ports for use in a wide variety of applications. The cards were designed to offer serial compatibility with the PCI Express bus and to be used by system integrators and manufacturers in the design of industrial and commercial systems.
-
Product
OC-3/STM-1 And OC-12/STM-4 Analysis And Emulation Card(w/ GigE And USB 2.0)
LightSpeed1000™
-
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames. GL's LightSpeed1000™ hardware platform (PCIe Card and USB Pod) is capable of OC-3/12 and STM-1/4 wire-speed processing on quad optical ports for functions such as wire-speed recording and wire-speed playback of Unchannelized and Channelized ATM, PoS, and RAW Traffic.
-
Product
PCI Smart Bus Extenders
PCIEXT-64U - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
