Infrared Sensors
Detect infrared radiation and produce a measurable signal of the detected amount.
-
Product
Temperature Sensor Module
-
A low cost solution for non-contact temperature measurements. The sensor is integrated with signal conditioning that reliably produces a calibrated linear digital output in a plug-and-play package having many options. Programmable outputs and flexible power requirements yield a turnkey solution for medical, consumer, commercial and industrial applications.
-
Product
LilyPad Light Sensor
-
The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from the board through the signal tab to the microcontroller you connect the sensor to. If the sensor receives no light, no current will flow through it. In a typical indoor lighting situation, the sensor will output around 1 to 2V. Adding this board into your next e-textile or wearable project will really open up the possibilities by being able to incorporate light level sensing capabilities.
-
Product
Car Oxygen Sensor
KS60044
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Wind Sensor
FT722
-
Specifically designed for wind turbine control, the FT722 reads wind speeds from 0-50m/s. Its inovative design incorperates a series of "turbulators" (patient pending) which condition the air flow. With updated software, and calibration in our new state-of-the-art wind tunnel, the FT722 delivers our highest levels of accuracy in wind speed, wind direction and accoustic temperature measurement.
-
Product
EMP Sensor
-
This is a nice gimmick which detects EMPs (i.e. when lighting takes place). There are many sensors around, to detect all kind of things. However, detect lighting strikes is a complete different area. Use this sensor for :*Pre-warning systems*Digital photography*Domotics*Weather-station*Arduino experiments*School / scientific experiments
-
Product
Flush Diaphragm Pressure Sensors
-
Honeywell Industrial Automation
For high-frequency pressure measurements or in applications with severe space limitations, Honeywell Sensotec offers subminiature flush diaphragm pressure sensors in ranges from 0100 psi to 020,000 psi (010 to 01,400 bar). All-welded, machined stainless steel sensing diaphragms ensure ruggedness. Bonded piezoresistive and metal foil strain gauges offer high reliability. Millivolt and optional high-level outputs are compatible with most data acquisition systems.
-
Product
Nutrient | Oxygen | PH Sensors: Oxygen Sensors
-
Oxygen sensors measure dissolved oxygen in the water. Sea-Bird oxygen sensors are designed to be integrated with a pumped CTD, and can be easily added at the factory or in the field to the plumbing on Sea-Bird CTDs that can accomodate auxiliary sensors.
-
Product
Citroen Oxygen Sensor
KS60113 - Citroen
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Optical Sensors
-
Vishay's proximity, reflective, transmissive, slotted interrupters, optical and ambient light sensors put the "smart" into smart devices. Advantages of Vishay sensors include best-in-class performance, in-house chip manufacturing and assembly including AEC-Q101 automotive grade product lines, and comprehensive range of package types for wide range of applications.
-
Product
Multipoint Temperature Sensor
TSM800
-
The TSM800 multipoint temperature sensor is ideally suited for measurement of process temperatures over multiple locations with a single access point.Typically used in process plant vessels the TSM800 provides a cost effective alternative to mounting multiple individual sensors and their associated process vessel entries.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Light Section Sensors
-
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
-
Product
IR Sensor
-
The sensor measures a very useful 0.17 mm in thickness and is made of plastic. Essentially it is a piece of robust plastic that can be used “bare” – without protective housing, such as a metal casing commonly used by other producers. The sensor it is less than 0.2 mm. thin and it is made using plastic membrane. This configuration makes the sensor so robust it can be used “bare” – without protective housing such as a metal container. Due to the fact thatSince the sensor chip can be used applied bare, means it can be used in a totally new ways, which can re-defines todays the current view on application design and reduces the cost of the entire system, and not just the sensor-element as such.
-
Product
Calcium Logger Sensor
NUL-238
-
The NeuLog calcium sensor enables measurements of ionic calcium (Ca2+) concentration in aqueous samples. This measurement is very important when evaluating water quality. It can also be used to determine calcium magnesium by EDTA titration.
-
Product
Photo Gate Logger Sensor
NUL-209
-
This sensor can be used to study various kinds of motion. With six modes of operation, time, velocity or acceleration can be measured with one or two photo gates and associated timing cards, as well as showing pictorially the status (digital 1 or 0) of the voltage output of the photo gate as timing cards pass through it.
-
Product
Thru-beam Type Ultrasonic Sensor
US-N300
-
Panasonic Industrial Devices Sales Company of America
The Panasonic Thru-Beam Type Ultrasonic Sensor is suitable for detecting transparent film or objects.
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
-
Product
Compact Inductive Proximity Sensor
GA-311/GH
-
Panasonic Industrial Devices Sales Company of America
With a 3.3kHz response frequency, the GH Series Inductive Proximity Sensors are ideally suited for applications that require sensing of high-speed moving objects. These Proximity Sensors have the same form factor as Panasonic’s FX-300 Series Fiber Sensors and use the same shape quick-connection cables which, when used together, require minimal mounting space, but more importantly less power and wiring.
-
Product
SparkFun Current Sensor Breakout
ACS723
-
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
DC Voltage Sensors
-
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
Product
Motion and Sensor Additional Instruments
-
Our expansive line of Trig-TekTM motion and sensor instruments offers a myriad of test and measurement functionality.
-
Product
MSCL Sensors
-
Geotek specialises in designing core logging systems with multiple sensors to acquire both geochemical and physical properties non-destructively from geological core samples. The range of sensors that can be accepted onto each Multi-Sensor Core Logger (MSCL) is dependent on the type of core to be logged and the MSCL system selected.
-
Product
Inductive Sensors
-
Inductive sensor designed to detect shaft speed, shaft position, gate position, or object presenceTotally sealed constructionMulti-voltage 24 - 240 VAC/VDCDetects ferrous targets up to 5/16" (8 mm)IP 65 Protection
-
Product
Waveguide Power Sensor
-
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
-
Product
Wireless Modbus Sensors
-
Wireless Modbus Sensors & Condition Monitoring – The Best of 2 Worlds! Combining Phantom Wireless Sensors with an Industry Standard such as Modbus! The best in Vibration monitoring equipment!!
-
Product
Inertial Sensors
-
Our CV5 line of board-level OEM inertial sensors is ideal for platform stabilization, precision agriculture, terrain compensation, and more. Their small footprint and low weight enable them to install easily into almost any application. Our CV5-25 AHRS, CV5-15 VR, and CV5-10 IMU sensors offer industrial-grade precision at a fraction of the cost.
-
Product
Custom Sensors Products
-
Stellar Technology offers a comprehensive selection of pressure sensors, including pressure transducers and transmitters, that can be used in a variety of industrial applications.
-
Product
Rolling Shutter Image Sensors
-
Rolling Shutter devices start and then stop their exposure line by line. This means that that each line will be recorded at a slightly different exposure time. This effect is pronounced for short exposures which produces images with distortion due to moving objects and short flashes of light.
