Infrared Sensors
Detect infrared radiation and produce a measurable signal of the detected amount.
-
Product
Remote Particle Sensors
3718-A And 3719-A
-
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
Product
TAPPIR Femtosecond Transient Absorption Pump-Probe Infrared Spectrometer
TAPPIR
-
A femtosecond difference frequency generator (DFG) is installed inside the TAPPIR optical unit for the tunable probe of transient absorption within 3 mm - 11 mm. DFG is pumped with signal and idler waves delivered together from an external optical parametric amplifier.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
S2 Penta High-Sensitivity Sensors
ULP S2 PCI/V HS
LED Sensor
The Universal LightProbe S2 Penta High Sensitivity Sensor features the same popular built-in color binning as the regular S2 Penta Sensor, and is designed test extremely dim LEDs, providing an analog output for intensity, ranging from 0 to 4 volts, corresponding to the LED’s luminous intensity in millicandelas. Implemented in a unique and customizable 2-Part solution, the S2 Penta High Sensitivity Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: <1.2s color & intensity outputs simultaneously (the brighter the LED, the shorter theresponse time)Fiber-Optic Probes: Wide Aperture Fiber-Optic Probe recommended
-
Product
Sensors
-
YUEQING WINSTON ELECTRIC CO., LTD
Expansion sleeve is a keyless connection device, its principle and use is through the action of high strength tensile bolt, between the inner ring and shaft, between the outer ring and the hub of a huge holding force, in order to achieve the keyless connection between the parts and the shaft.
-
Product
Temperature Sensors
-
Our temperature sensors supply important data on the ambient or module temperature in photovoltaic systems.
-
Product
Infrared Thermometer
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.
-
Product
Web Sensor
T3511P-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Leakage Current Sensors / Small Current Sensors
-
ChenYang Technologies GmbH & Co. KG
This current sensor is based on magnetic modulation and compensation principle, and can beused for measurement of small DC current and leakage current, current difference between two ormore conductors.
-
Product
Sensor Bodies
-
The armature - assembled sensor body - is the central component of an inline photometer. We have already designed more than 1000 different sensor bodies and more than 50 types are always on stock. All optek inline sensor bodies are made from high quality materials and are machined with extreme precision. The quality-tested manufacturing tolerances allow optical path lengths of up to 1000 mm, for which the accuracy of the incoming and outgoing light beam is ensured by testing a laser-based coaxiality tolerance test to the reference axis. To cover a wide spectrum of different process conditions, optek sensor bodies can be manufactured from various materials (also for aggressive chemicals or with NACE MR 0175) and adapted with regards to:
-
Product
Position Sensors
-
Panasonic Industrial Devices Sales Company of America
Analog input devices are designed for highest requirements like within the automotive market. In SMD or THT technology, with detents or without detents, the electrical as well as the mechanical performance is impressive. Key features like “long-life endurance” or “accuracy in output-signal” give customer applications highest performance. Possibilities of Haptic-alignment make these components perfect.
-
Product
Ultra-slim Body Picking Sensor
NA1-PK5/NA1-5
-
Panasonic Industrial Devices Sales Company of America
The NA1-PK5 Series is a new Area Sensor that prevents the wrong part from being picked and has an ultra-thin design to save space.
-
Product
Remote Sensors
-
The most versatile and popular sensors we make. The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. All these sensors have the "on-target" green LED indicator
-
Product
Color Sensor
-
The color sensor product family includes both RGB (Red, Green, Blue) and high-accuracy XYZ light sensors for precise color measurement, determination, and discrimination. XYZ sensors are capable of providing xy chromaticity co-ordinates in accordance with the CIE 1931 color map. The ams color sensors include filters to block unwanted IR light in the visible spectral range, enabling highly accurate color measurement. Their high sensitivity coupled with their wide dynamic range make them well suited to continuous color temperature measurement of ambient light in display management systems, and automatic-white-balance assistance in camera applications. Some products have additional IR channels to assist with IR light source identification.
-
Product
Vehicle Presence Sensor
TrafiCam
-
FLIR TrafiCam is a vehicle presence sensor that combines a CMOS camera and a video detector in a single unit. FLIR TrafiCam detects moving and stationary vehicles at signalized intersections. Via detection outputs, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. This way, vehicle waiting time at traffic lights is reduced and traffic flows are optimized.
-
Product
Capacitance Sensors
Accumeasure Series
-
The Accumeasure product line features capacitive sensor products for high resolution gap and displacement measurements that require a high level of accuracy that is both stable and repeatable. A capacitive sensing system consists of a probe and amplifier. Capacitive measurements can be performed in a multitude of environments using non-contact passive capacitance probes that are not affected by magnet fields, temperature, humidity, nuclear radiation, and pressure. This is largely due to the nature of the rugged and passive capacitance probes.
-
Product
Wireless Vibration Sensors
-
A Wireless Vibration Sensor is a device that includes an Accelerometer and is capable of measuring vibration and send it to a receiver using a Wireless protocol. Depending on the wireless protocol used, some of these sensors may even transmit data in real time. Hence having the capability to connect via peer to peer or mesh network.
-
Product
SparkFun Humidity Sensor Breakout
SHTC3 (Qwiic)
-
Looking to keep a log of the climate in your greenhouse, create a humidor control system or want to track temperature and humidity data for a weather station project? The SparkFun SHTC3 Humidity Sensor may be the perfect option for you! The SHTC3 is a low cost, easy-to-use, highly accurate digital humidity and temperature sensor. The SHTC3 communicates via I2C so, as you can tell by the name, we have broken out the pins on the sensor to Qwiic connectors so you can easily connect it to SparkFun's ever growing Qwiic Ecosystem.
-
Product
Peak, Pulse, and Average Sensors
-
These sensors provide quick and easy measurements of pulse power, continuous wave power and other signals. Many of our competitors claim to measure pulse power, however you must input your duty cycle and the power is calculated based on that. Our sensors offer trigger based measurements and the pulse itself is examined giving better measurement uncertainty. There is no need to input the duty cycle to calculate pulse measurements, our sensors measure it.
-
Product
Non-Contact Sensors
IRIX
-
Sciences et Techniques Industrielles de la Lumière
IRIX™ is a family of non-contact sensors based on chromatic confocal technology capable of measuring distances and thicknesses on any material transparent to white light.IRIX™ is capable to measure simultaneously up to five layers of material. The controller can be used in combination with a large family of optical probes with different measurement ranges, mechanical dimensions and metrological specifications to best meet the most diverse application needs.
-
Product
MEMS And Sensor Test Solutions
-
Modular design based on standard handlers, high parallelism, ambient to automotive tri-temp handling.
-
Product
ADB Bearing Sensor Tester
-
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
Product
GMC Oxygen Sensor
KS60113 - GMC
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
AMR Linear Sensors
-
MultiDimension Technology Co.,Ltd.
AMR linear sensor utilizes two push-pull Wheatstone bridges each composed of four highly sensitive AMR sensor elements. These Wheatstone bridges effectively compensate the sensor’s temperature drift to achieve outstanding temperature stability with minimal noise.
-
Product
Electrostatic Sensors
-
Panasonic Industrial Devices Sales Company of America
With easy data management, Panasonic Electrostatic Sensors can assist to identify and diagnose problems caused by static electricity. In real time, these Sensors can determine ionizer status and identify ionizer damage. With a measurement range up to +/-2 kV and suitable for severe conditions, these Sensors can be used for measurements such as surface potential, frictional electrification and lead frame charge removal.
-
Product
Web Sensor Hygrometer
T3511-2
-
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Atmospheric Pressure Sensor
SBS-02A
-
Provides: Altitude and rate of climb/descent data. Range: 500-1100hPA or 162.4-16,000 feet (-50 to +5500 meters). Weight: 0.10 oz. (2.7 g)
-
Product
Intelligent Sensors
-
Silicon Labs is a leading supplier of intelligent sensor solutions that are characterized by superb reliability, compact size, high levels of integration and unmatched ease of use for a variety of applications. Our diverse sensor product portfolio includes optical sensors, digital relative I2C humidity and temperature sensor ICs, biometric sensors and capacitive touch sense microcontroller devices.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Digital Fiber Sensor
FX-410
-
Panasonic Industrial Devices Sales Company of America
This dual display digital Fiber Sensor is unique with its manual threshold value setting. Just "Look" and "Turn" simple, easy-to-use Fiber amplifier. The incident light intensity and threshold values can be checked at the same time with operation needed. In addition, no complex mode settings are needed when the values are adjusted.
