Signal Conditioning Systems
-
Product
Seat Actuation Systems
System
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
Product
Regenerative Battery Pack Test System
17020
Test System
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
Product
Mezzanine System
5033
System
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
Test System
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
Multipurpose Mobile PXI DAQ System
System
The mobile DAQ system achieves seamless integration among signal conditioning, data acquisition, and synchronization that benchtop instruments would not have achieved. By choosing this system over using benchtop instruments, United Technologies Research Center saved hundreds of thousands of dollars.
-
Product
In-Circuit Test Systems For Sale
Test System
Forwessun offers a comprehensive range of global services for a variety of Test Systems. We provide refurbished systems that have undergone rigorous testing, giving you reliable performance at a fraction of the cost of new equipment. Whether you’re looking for a long-term solution to enhance your testing capabilities or a temporary setup to meet increased production demands, we have flexible options to suit your needs. - HP3070- Agilent - Keysight- GenRad- Teradyne Our bespoke rental agreements make it easy to scale up without permanent investment—simply return the system when it’s no longer required. For ongoing support, we offer calibration, repair, and maintenance services through convenient service contracts. If you’re looking to retire any outdated or non-functional In-Circuit Test (ICT) systems, we’ll offer fair market prices, helping you maximise value on any surplus equipment.
-
Product
TO-CAN Package Inspection System
7925
System
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
Product
BMS Manufacturing Test System
Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
Wafer Chip Inspection System
7940
System
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.
-
Product
Semiconductor Test Software
Test System
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Systems Certification
System
Project integration offering a complete turnkey solution including design, engineering, FAA and international regulatory certification services and testing, and installation kit manufacturing.
-
Product
VXI Digital Multiplier
4152A
Test System
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
VPX Development System
VPX370 3U
System
The VPX370 is a second generation VPX development platform that delivers, performance, flexibility, and scalability all in a compact 3U VPX form factor.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
-
Product
Mezzanine System Carrier
MMS6245
System
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
Product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
SAS Protocol Test System
Sierra M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
Display Driver Test System
T6391
Test System
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
In-Process Wafer Inspection System
7945
System
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
Product
Aircraft Data Systems
System
Aircraft data systems for commercial and military applications, including Aircraft Interface Devices (AID), avionics I/O computers, avionics test & simulation interfaces, and Embedded avionics interfaces.
-
Product
Smart Aircraft System
System
The Astronics Smart Aircraft System makes that possible. Our patented system enables the immediate, cabin-wide gathering of thousands of data points using sensors & IoT (Internet of Things) technology. The result? You get the insightyou need—when you need it. Insight that helps you on every flight. Insight that allows you to improve your operational efficiency, your cabin safety, and your overall passenger experience.
-
Product
Benchtop Communication Test System
ATS3000A
Test System
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 24 AWG White, Single Ended (5 Amps)
7-124924000-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 24 AWG White, Single Ended (5 Amps).
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps)
7-123926000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps).
-
Product
Signal, Patchcord, Receiver, 72", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
Product
UXG X-Series Agile Signal Generator, 10 MHz to 40 GHz
N5193A
Signal Generator
Get closer to reality: simulate increasingly complex signal environments for radar, EW & antenna-test Test sooner & increase confidence in EW systems by generating signal simulations when you need them: the UXG is a scalable threat simulator Use pulse descriptor words (PDWs) to generate long pulse trains & individually control pulse characteristics Accurately simulate multi-threat environments: 180-ns PDW update rate, chirps 10 to 25% of carrier frequency, pulses as narrow as 10 ns
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 18 AWG White Teflon, Single Ended (10 Amps)
7-101918000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", TriPaddle, 18 AWG White Teflon, Single Ended (10 Amps).
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
