Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
Product
2-CH Counter/Frequency Input Module
ND-6080
Data Acquisition Module
- Channels: 2 independent 32-bit counter- Input Frequency: 100 kHz max.- Isolation Voltage: 5000 VRMS- Input Pulse Width: > 10 µs*- Max. Count: 4294967295 (32-bit)
-
Product
PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
RADAR Stability Testing
PN9002
-
Radar component and system testing usually evokes images of complex, expensive measurement systems occupying multiple equipment racks. In some cases, radar equipment designers have even used entire radar systems as a proving ground for their new components and modules. With the introduction of the PN9002 pulse-to-pulse radar stability test set from Noise eXtended Technologies , radar testing has become significantly less complex and costly. The modular PN9002 system provides outstanding dynamic range at frequencies from 2 to 18 GHz and optionally from 0.4 to 18 GHz.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614D-009
Multiplexer Module
The 40-614D-009 (PXI) and 42-614D-009 (PXIe) 4-bank, 4-channel, 8-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
RF modules
-
Dresden Elektronik Ingenieurtechnik GMBH
2.4 GHz OEM module with chip ceramic antenna based on the ATmega128RFA1 single-chip microcontroller from Atmel
-
Product
PXIe Power Relay Module, 1xSP4T, 20 Amp
42-166-203
Relay
The 40/42-166-203 is a PXI/PXIe high density power relay module with 1xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
PXI/PXIe High Voltage Programmable Resistor Module, D-Type Connector
40-230-133-HI
-
The 40-230-133-HI (PXI) and 42-230-133-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe RF Matrix, 8x2, 1GHz, 50Ω, SMB
42-750A-511
Matrix Switch Module
The 40-750A-511 (PXI) and 42-750A-511 (PXIe) are 50 Ω 8x2 RF matrix modules with SMB connectors suitable for switching frequencies up to 1000 MHz. They are part of a range of 8x2 matrix modules with 50 Ω or 75 Ω characteristic impedance with front panel mounted SMA, SMB or MS-M multiway coaxial connectors.
-
Product
8 Slot, 3U, PXI Chassis - Low Noise Fan
40-908-201
Chassis
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules. Mechanical expansion space on the right hand side allows the chassis to accept multi-slot modules, such as the BRIC, while only occupying one electrical slot.
-
Product
Small Footprint NIR Spectrometer
PGS Series
-
ZEISS PGS modules with a spectral coverage of 960 - 2200 nm are among the market leading NIR spectrometers, providing a small footprint, highest throughput and excellent SNR. Special TE-cooled/uncooled InGaAs detectors ensure lowest noise conditions.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-054-HI
-
The 40-230-054-HI (PXI) and 42-230-054-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Breadboard Module, 1-Slot, 96-Pin Micro-D
40-220A-001
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI 8 Slot BRIC 64x12 2A 1-Pole Matrix
40-597-102
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 12-Slot BRIC Matrix, 30x32 1-Pole (6 sub-cards)
40-562B-321-30X32
Matrix Switch Module
The 40-562B-321-30X32 is a high density BRIC12 matrix module with a size of 30x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Network Analyzer N-Port Calibrated Measurements
S95551B
Network Analyzer
PXI vector network analyzers (VNA) offer the capability to extend the number of ports for your measurements by using additional modules. When multiple modules are used, they are configured for multiport operation. The S95551B adds a multiport analyzer mode that enables full multiport error correction and measurement capabilities. The instruments may be identified as one VNA by the firmware running on an external host PC. At least one VNA instrument connected to your PC must have one S95551B license to maintain N-port capabilities.
-
Product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Single-point Current Meter
-
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.
-
Product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
TB-2631B , Term Block for NI PXI-2530B 4x32 1W or 4x16 2W Matrix
781688-01
Terminal Block
The TB-2631B provides a PXI front-mounting terminal block to configure the PXI-2530B PXI Multiplexer Switch Module. It provides direct signal wire connections to the screw terminals inside the terminal block.
-
Product
Interface Module
MRS4
-
The mezzanine provides connection of up to four input and four output interface lines.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 348x6, 6 Sub-cards
40-596A-106
Matrix Switch Module
The 40-596A-106 is a PXI 1-pole 348x6 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
RF Multiplexer
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
Product
Automated Metrology System
EVG®50
-
High-throughput, high-resolution metrology for bonded stacks and single wafers. The EVG 50 (fully automated stand-alone tool) and the Inline Metrology Module (integrated in EVG''s high-volume manufacturing systems) offer highly accurate measurements at high speed, utilizing different measurement methods for a large number of applications. The tool''s application range covers multi-layer thickness measurements for determination of the total thickness variation (TTV) of an intermediate layer, the inspection of bond interfaces as well as resist thickness measurement, and meets the most demanding requirements of the yield-driven semiconductor industry.
-
Product
4-Channel 200 MHz A/D with Multiband DDCs, Kintex UltraScale FPGA - 3U VPX
Model 52862
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four wideband DDCs and- 32 multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI 8 Slot BRIC 22x16 2-pole (2 sub-cards)
40-562A-122-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
QorIQ P40x0 Processor AMC, SRIO
AMC719
-
The AMC719 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.4 and AMC.2 specifications and the SRIO runs as dual x4. The module has options for up to 16GBytes of DDR3 memory with ECC.
-
Product
XMC Mezzanine Module 2 x SFP+
DN3-SHARK XMC 2.0
-
The DN3-SHARK is a is a XMC standard mezzanine card, equipped with a dual port 10Gbps Ethernet controller.
-
Product
Intrinsically Safe Temperature Module
ATMi
-
AMETEK Sensors, Test & Calibration
The ATMi intrinsically safe portable temperature modules offer the functionality and flexibility to read up to two temperature inputs with a single HPC50 handheld pressure calibrator. Use the modules to add temperature measurement to the HPC50 series calibrator. The ATMi intrinsically safe temperature modules deliver the same high level accuracy whether in the lab or in the field.
-
Product
8 Channels, RTD Measurement
RT1
-
The module provides 8 measurement channels, and can be programmed for interfacing to 2, 3, and 4-wire platinum RTD sensor configurations. The 4-wire mode (default) is the most accurate, providing excellent stability and repeatability. The RTD channels feature individual A/D converters and precision excitation/current drive. Programmable lead-wire compensation is provided for inherently less accurate 2 and 3-wire configurations. All RTD channels are self-aligning because each channel is automatically "aligned" on a rotating basis to eliminate offset and gain errors throughout the operating envelope. Programmability for expected resistance range and wire modes allows for optimization of scaling/resolution, as well as flexibility in reading many RTD types.
-
Product
PDS Caisson Placement Software
-
- Computation relative to previous placed objects- Placement guidance is accurate and reliable- One software suite for a complete solution for your project- Easily integrated with other modules of Teledyne PDS- Easy to use software for your application
