Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
Product
Dual Channel MIL-STD-1553 BC/RT/MT cPCI Intelligent Module
DP-cPCI-5664
-
The DP-cPCI-5664 provides new level of performance and flexibility for MIL-STD-1553B notice 2 in a Compact PCI form factor. It has full intelligent interfacing between a cPCI bus and one / two independent dual redundant MIL-STD-1553B data buses. The 1553B bus functions are fully controlled by a DSP processor. Software controls the operation of the channel as either a 1553 Bus Controller (BC), Remote Terminal (RT), or Bus Monitor (MT).
-
Product
JTAG External Modules for Cluster Test
JEMIO
-
The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-242-HI
-
The 40-230-242-HI (PXI) and 42-230-242-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Carrier Boards
ROM-DB7501
Carrier Board
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
MI/O Extension Modules
-
Advantech‘s MI/O extension modules and evaluation boards are designed for MIOe embedded single board computers (SBC) to extend functions such as USB 2.0/USB 3.0,and provide additional I/O interfaces via a high-speed connector.
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
785045-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V,based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
GCxGC Time-of-Flight Mass Spectrometer
PEGASUS® BT 4D
-
The Pegasus BT 4D offers enhanced sensitivity by coupling our benchtop Pegasus BT with our high performance GCxGC thermal modulation system. This combination gives the Pegasus BT 4D the ability to interrogate challenging samples where the best sensitivity is needed. Unique and powerful software and hardware features simplify quantitation, while also dramatically making GCxGC easy to use and understand.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, SMB
42-877A-001
Matrix Switch Module
The 40-877A-001 (PXI) and 42-877A-001 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
8-Channel High-Speed Analog Input Module
ADAM-5017H
-
Accuracy: ±0.1% or betterEffective resolution: 12-bit plus sign bit1000 Hz bandwidthHigh sampling rate:ADAM-5000/485&5000E: 100 samples/sec, ADAM-5510 & ADAM-5511: 8000 samples/sec max3000VDC Isolation voltage protectionDistinct range settings allowed on each channelInput type: mV, V, mA
-
Product
PXI 8 Slot BRIC 198x8 2-pole (9 sub-cards)
40-562A-122-198X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Standard Voltage 37 Pin D-Type Cables - Calibration Cables for Pickering
-
The cable assemblies below are suitable for use with Pickering precision resistor cards and modules that utilize 37-pin D-type calibration port connector.
-
Product
Receiver, 9025, 25 Module, Slide Mount, Telescopic Handle - Right Side
310104477
Receiver
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. This model is equipped with a telescopic handle on the right side. This handle is designed to rest flush against the side of the receiver as a standard handle, or can be extended out to the right up to 3" to accommodate a larger ITA enclosure or other obstruction that may prevent normal handle operation/ engagement.As with the standard 9025, a microswitch is included. Mounting flanges and an instrument bracket are also included for slide mounting. A slide kit is required, but not included. See 9025 procedure sheet/ user manual for instructions on choosing the correct slide kit length for your test rack. *Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
Product
RF Signal Generators
-
The G6 VSG from Transcom Instruments is a Vector Signal Generator that operates from 10 MHz to 6 GHz. It can simulate GSM, EDGE, CDMA, TD-SCDMA, WCDMA, CDMA2000, TD-LTE, FDD-LTE, NB-IoT, and LoRa base station signals for production and calibration of UE, chips. The signal generator has a dynamic range (power range) from -100 to 10 dBm and an in-built automatic gain control function. It is available in a module that measures 180 x 50 x 290 mm and is ideal for educational practices, wireless monitoring, mobile communication, aerospace and national defense industry in terms of research, manufacturing, testing and measurement, and electronic countermeasure.
-
Product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-802
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
12-Channel VME Current Loop/Process Control I/O Module
V220
-
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-145-HI
-
The 40-230-145-HI (PXI) and 42-230-145-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
COM-HPC Server Type Modules
Computer on Module
The COM-HPC specification currently defines two server modules. The largest of the server modules, Size E (200mm x 160mm), offers up to eight on-board DIMM sockets. The power input is a single 12-volt supply that can deliver up to 358 watts of power, and there are 64x lanes PCIe Gen5 in total.
-
Product
10 KS/s, 12-Bit, 8-Ch Multifunction USB Module
USB-4702
-
Supports USB 2.0Bus-powered8 x analog input channels12-bit resolution AISampling rates up to 10 kS/s8-ch DI/8-ch DO, 2-ch AO and one 32-bit counterPortable
-
Product
IC-INT-VPX3l, SOSA™-Aligned 3U VPX Intel® Xeon® W SBC
IC-INT-VPX3l
-
The IC-INT-VPX3l is a 3U VPX Single Board Computer based on the Intel® Xeon® W (code name Tiger Lake-H) processor and designed in alignment with the SOSA™ Technical Standard. This high-processing module is ideally suited for mil-aero applications and edge applications such as Mission Computer, Radar and Sonar HPEC.
-
Product
ITA, G18, 18 Module
410120111
ITA
You can mount a VPC Enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration. This solution is perfect for any medium to high I/O PXI application. The rugged aluminum frame provides secure mounting options for custom fixtures.
-
Product
PXI-2586 PXI Relay Module, SPST (open), 10-Channel, 300 V, 12 A
778572-86
Relay
10-Channel, 12 A, SPST PXI Relay Module—The PXI‑2586 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay has low contact resistance and high isolation voltage. The PXI‑2586 is fully software programmable. It is rated for both high currents and high voltages, so it is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-122-HI
Multiplexer Module
The 40/42-855A-122-HI is a PXI/PXIe dual 2-channel multiplexer with FC/PC, includes hardware interlock connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 4-Slot BRIC Matrix, 33x16 1-Pole (3 Sub-cards)
40-562B-021-33X16
Matrix Switch Module
The 40-562B-021-33X16 is a high density BRIC4 matrix module with a size of 33x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Receiver, S6, 6 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310122108
Receiver
The S6 Mass Interconnect Receiver is designed to mount to slides in a rack application or directly to a tabletop. It features positive-latching mechanisms and integrated guide pins to create a highly reliable engagement system. The S6 Receiver is very versatile and has module positions screened on top for ease of module placement.
-
Product
PXI 2A 39xSPST High Density Power Relay Module
40-137-201
Relay
These Power Relay Modules are suitable for applications requiring power relay switching with high density. The feature 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 39 x SPST version, the range also includes a 32 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
Product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXIe Power Relay Module, 10xSPST, 16 A, With Interlock
42-161A-003-HI
Relay
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-114-HI
-
The 40-230-114-HI (PXI) and 42-230-114-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-02
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
