Reactive Load Banks
Provide both lagging and leading power factor loads.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Resistive Load Banks
-
Product
AC Load Bank
XL750-XL800 Series
-
Mosebach Manufacturing Company
The XL750-XL800 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
Product
PXI MUX 1 Bank of 128 Channel 1 Pole
40-610-022-1/128/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Motor Test Bench For No Load Test
-
The testing equipment is extensively used in industries for testing of motors under no load conditions.
-
Product
Small Compressive Load Cell
CCSM-3.0
-
DLM’s range of Small Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
Loading Rheostats (Resistive Load)
-
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Benchtop DC Electronic Load
63000
-
Chroma Systems Solutions, Inc.
The 63000 series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power supplies, A/D power supplies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices.
-
-
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
-
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
-
Product
Electronical Load Board 3U VME64x (air cooled)
056-921
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
RF Loads
-
Bird manufactures a broad spectrum of devices from one watt to eighty kilowatts. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators and RF loads.
-
Product
PXI 4 Banks of 20 Channel 2 Pole MUX
40-615-022-4/20/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI Solid State MUX, 2 bank, 80 channel
40-680-005
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Outdoor Permanent Mounted Load Bank
-
Mosebach Manufacturing Company
Mosebach Pad Mounted Load bank is designed to be permanently mounted next to a generator for dedicated testing. Its unique design allows it to be one of the smallest on the market! This size enclosure will fit 50 kW, 75 kW or 100kW of testing ability. Also available in 300kW and larger load banks.
-
Product
Arbitrary Load Control For Modulation Distortion
S94570B
-
Extend the modulation distortion application by computing figure of merits such as EVM and ACPR for any desired load with arbitrary load control (ALC). Modulation distortion with ALC integrates the powerful capabilities of the PNA-X with an electromechanical tuner so a non-50 Ω load can be presented to the DUT and changes in device performance or sensitivity to varying load conditions can be accurately measured.
-
Product
Performance & Load Testing for APIs, Mobile and Web Apps
-
Test the performance of any mobile app, website or API in under 10 minutes. Simulate up to one million users with our developer-friendly, self service platform. 100% compatible with Open Source Apache JMeter. Supports Selenium.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
Product
PXI 2 Banks of 40 Channel 2 Pole MUX
40-615-022-2/40/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Tension Load Cells
-
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
-
Product
Programmable DC Electronic Loads
SDL1000X/X-E Series
-
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
600 Watt DC Electronic Load Mainframe
N3301A
Mainframe
The Keysight N3301A is a half-rack width mainframe with 2-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3301A holds up to two N3302A, N3303A, N3304A, and N3307A load modules, or one N3305A and N3306A load modules, allowing up to 600 watts of total maximum power.
-
Product
Load Cells
-
Load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or balance and transmit it to a weight indicator . The load cell is an essential component in any scale or electronic balance and they come in different models and specifications. A Wim load cell is essential for a weighing system where precision, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for each need, in addition to offering all the advice you need to choose the model that best meets the particular needs of your weighing system and always backed by WIM-Systems quality and technology.
-
Product
Load Monitoring Units (LMUs)
-
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
