RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
SMART III RF Probe
-
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
Product
RF Power Detectors
-
Monitors or samples the output of an RF circuit and develops a dc output voltage pro- portional to the power at that point.
-
Product
Electromagnetic Ammeters And Voltmeters Fb-1, AC Electric Current, AC Voltage
-
ELECTROMAGNETIC DEVICES FOR MEASUREMENT OF ACTIVE VOLTAGE AND ACTIVE CURRENT.
-
Product
RF Capacitance Level Switches
-
ABB's RF Capacitance level switches feature one-step external calibration, immunity to material build-up, and a wide selection of probes for even the most challenging applications from low dielectric bulk solids to sticky slurries.
-
Product
Multi-Purpose RF Test System
SPA1241
-
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
Product
Deep Access RF Probes
-
GigaTest Microwave Probes are perfect for device characterization and modeling. GigaTest Probes have a high tolerance allowing them to land repeatedly and take high-quality data.
-
Product
RF Front-end
-
The RF integrated passive device (RF IPD) uses a high-resistivity substrate to integrate quality factor components such as capacitors and indictors. Many functions like impedance matching networks, harmonic filters, couplers, baluns, and power combiners/splitters can be designed using IPD technology. ST's IPDs are manufactured using thick film and HiRes Si or glass wafer manufacturing technology and photolithography processing.
-
Product
RF Testing, Screening and Qualification
-
DPACI has extensive experience in providing RF testing, screening, as well as QCI services to a diverse range of customers, such as Lockheed Martin, General Dynamics, and Ball Aerospace. We have a fully equipped RF and microwave lab with test capabilities ranging from 40 GHz to 300 GHz for providing RF packaging.
-
Product
RF Connectors
-
Radio Frequency Coaxial Connectors Are Designed To Connect Printed Circuit Boards (PCBs) And Cables To An External Antenna, Cameras, Sensors Or Other Devices.
-
Product
CATV / RF Over Fiber
-
Transport RF signals: Cable TV (CATV), L-Band (SMATV), NTSC, DOCSIS, Return Path and other RF signals over 110km over a single fiber.
-
Product
50 Ohm MCX to MCX Cable Assembly
40-977-561-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
RF Shielded Box
LTL B12001
-
LTL B12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B12001 RF shielded test enclosure can comfortably houses the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
RF Monitor Recertification
-
The use of RF personal monitors is widespread among wireless tower climbers and technicians. This is a relatively new development of the last five years or so. Prior to that, only a few monitors were in use. These were typically models developed for use by engineers, with a host of features not needed for routine climber protection. Consequently, they were expensive and not frequently used. As safety managers have begun to require all personnel working on wireless facilities to have personal monitors among their personal protective equipment, a new generation of cost effective equipment has emerged.
-
Product
RF Filters - Notch
-
A specialized band-reject filter that blocks or significantly weakens a very narrow range of unwanted frequencies (the "notch") while letting all other desired frequencies pass through relatively unchanged.
-
Product
LXI 50Ω RF Matrix - 2.4GHz
Matrix Switch Module
Pickering's LXI 50Ω RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
-
Product
RF Connectors
SMA Connectors
-
Utilizing a threaded interface, SMA 50 ohm connectors are semi-precision units that provide excellent electrical performance from DC to 34 GHz and outstanding mechanical durability.
-
Product
RF Connectors
AMC Connectors
-
The AMC (Amphenol Micro Coaxial) connector series is a low profile (2.5 mm height off the board) series with an extremely small board footprint (3mm x 3mm).
-
Product
Board Level Voltmeters
-
We've shipped more than half-a-million on-board controllers (OBCs) to manufacturers across the world. Our non-contact OBCs offer the accurate, drift-free, high-speed, and low noise measurements your applications require.
-
Product
RF Microwave Switch Matrices
-
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
-
Product
Portable Cable/Digital TV RF Analyzer
SLM 1479
-
7” full-color, high-resolution touch screen user interface simplifies complex measurement tasksFull motion video and audio decoding of received channelsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
Product
EMCTD Broadband RF Safety Systems
-
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
Product
RF Bias Burn-In System
-
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
Product
RF Detectors
-
RF detectors from Fairview Microwave are available with N Type or SMA connector series inputs and BNC or SMA connectors for outputs. Fairview RF detectors are zero bias Schottky diode and have negative video out. These zero bias Schottky diode detectors for RF have a minimum frequency between 10 MHz and 2 GHz and maximum frequency range between 2 GHz and 26.5 GHz.
-
Product
RF Streaming Solutions
-
Systems that can record spectrum from DC to 50 GHz with instantaneous bandwidths of up to 1 GHz. Bird's high-resolution long duration RF signal storage and re-creation capabilities can dramatically increase the power of your spectrum analyzers and vector signal generators from test & measurement industry leaders.
-
Product
RF Adapters
TNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series TNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance TNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm TNC connectors have a frequency range from DC to 11 GHz. 75-ohm TNC connectors have a maximum frequency of 3 GHz.
-
Product
Voltmeter
DC Moving Coil
-
*Compact in size (build in depth 33mm).*Rugged movement ensures sustained accuracy and reliability.*Square bezel permits edge to edge mounting, allowing maximum use of panel space.*Clear scaling for easy reading.
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
RF Tracking Generators
-
Using a Spectrum Analyzer (SA) in combination with a Tracking Generator (TG) enables swept scalar frequency response measurements of active and passive networks.
