Analog Multimeters
analog display multi function measurement instrument.
See Also: Multimeters, Digital Multimeters, Bench Multimeters
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Analog and Digital Interface
421
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
-
Product
Digital Multimeters
-
The wide variety of our DMM line provides the customer with different functions and accuracy depending on the requirements. From our simple pocket digital multimeter to our high accuracy TY series, with up to 50,000 counts on a dual display, Yokogawa's DMMs provides you with a quality product to meet all your expectations.
-
Product
mAEStro Audio Analog to Digital Converter
-
The mAEStro AADC-100 accepts balanced stereo analog audio inputs and converts them into a single digital bit stream in compliance with the AES/EBU (AES3) and S/PDIF digital audio standards. It generates 24-bit values and uses 128 times over-sampling for extremely accurate and linear analog to digital conversion, as well as offering a high dynamic range with exceptionally low total harmonic distortion and noise.
-
Product
12-bit, 100KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3001-8
-
8 single-ended or 4 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Compact Digital Multimeter
400001
-
An easy to use unit that delivers safe, reliable measurements, time after time. These meters are made to fit the way you work, and designed to go along no matter where your work takes you.
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
Analog Expansion Board
MSXB 014
-
The MSXB 014 Analog Expansion Board provides 4 additional analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a single DAP for a total of 64 additional output channels.
-
Product
16-CH 0-20mA Analog Input EtherCAT Module
EPS-3216
-
ADLINK's EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Oscilloscope: 100 MHz, 4 Analog Channels
DSOX2014A
Oscilloscope
100 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Multimeter Cables
-
Criem multimeter cables - needle tip cable, 4 mm multilamine tip cable, etc.
-
Product
Analog Functions
-
Analog Devices designs amplifiers and linear products that deliver high performance and high value. We combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
Batch Controller (analog input)
-
Same capabilities as the Laureate pulse-input batch controller, but for 0-1 mA, 4-20 mA, or 0-10 V process signals, as made possible by a built-in voltage-to-frequency (V-to-F) converter. Square root extraction is standard for use with flow meters.
-
Product
Digital multimeters
-
PROMAX testers are very popular in technical schools, as well as in technical support centres or electronic laboratories.
-
Product
Digital Multimeters
-
*5½-digit resolution to 8½-digit resolution DMMs*6ppm basic voltage measurement accuracy on the 8½-digit DMM for calibration laboratories*Fast, 1 Msample/s sampling speed to capture complex, low level current profiles from IoT devices or other wireless devices*Sensitivity of 1 µΩ and 1 pA to test low power devices for research, design, and manufacturing test*A wide range of measurement functions such as DC and AC volts, DC and AC current, two- and four-wire Ohms, continuity, frequency, period, RTD, thermistor, and thermocouple temperatures, diode test, and capacitance*Numerous interface options including LAN/LXI, USB-TMC, GPIB, and RS-232 for data acquisition and automated testing*Intelligence to execute tests and create customized measurements with minimal PC interaction*Measurement expansion up to ten channels
-
Product
Double Display TRMS Multimeter with USB Interface
VA42 VA42R VA42RP
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
This instrument complies with IEC 61010-1:2001, CAT II 1000V and CAT III 600V overvoltage standards. See Specifications.
-
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Analog Measurement Unit
AMU05
-
The AMU05 (Analog Measurement Unit 05) is the core of all our test systems. It ensures that all the measurements are performed faster, more accurately and with even greater stability.
-
Product
Analog Power Transducers
ROCHESTER
-
AMETEK Power Instruments offers a wide range of Rochester Analog Power Transducers for meeting all of your power measurement needs. The transducers consist of two families of products; the Process and Ultra series. Each one is designed to provide an exact fit for your monitoring application.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Service Telephone for POTS / Analog Line
1TA701
-
Test Phone is self-powered, portable telephone test set for use by servicemen that are providing installation, maintenance and repairs of the terminal telecommunication equipment. Test Phone is intended to be used in normal environmental conditions.
-
-
Product
Power System Multimeter
928A
-
The Model 928A Power System Multimeter with Floating-Point DSP™ Digital Signal Analysis is an AC Power measurement instrument, providing outstanding performance and flexibility in a small, hand-held package. Not only does the Model 928A measure basic data and power quantities, but it also measures power quality including harmonics, flicker, sags, surges and interruptions. Incorporating a graphic LCD display, serial communications, real time clock and an unprecedented combination of features makes the Model 928A the ideal instrument for the power professional.
-
Product
AC + DC TRUE RMS Digital Multimeter With PC Interface
KM 829
-
Kusam Electrical Industries Limited
• Beep-Jack Audible & Visible Input Warning• Auto-Ranging• Relative Zero Mode• PC Interface Capability• AutoCheck V-Ω ; Auto-Ranging• Crest (Instantaneous Peak Hold)• T1-T2 differential Temperature readings.• Data Hold
-
Product
Isolated SCIM5B Analog Signal Conditioning Products
SCIM5B
-
BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.
-
Product
Analog Meter
PR-A Series
-
The PR-A Series of series-regulated CV/CC power supplied were designed to provide a compact power supply package with high performance, and ensure excellent reliability as well as excellent design. Four types are available, three 18V types and one 36V type. Whether used individually or connected in series or parallel for greater capacity, the PR-A Series are housed in a compact rack-mount package and can be used on the bench top as well.
-
Product
3.5 Digit Handheld Multimeters
U1230 Series
-
Keysight U1230 Series (U1231A, U1232A, U1233A) multimeter – the first to combine a built-in LED flashlight, both audible and visual alerts, and non-contact AC voltage detection in one handheld. Whether it is dark, noisy, or dangerous, the U1230 pocket multimeter will equip you with features that anticipate your worst-case scenarios.
-
Product
32-CH ±10V Analog Input EtherCAT Module
EPS-3032
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
