PCI Carrier
PCI card facilitating the integration of other bus type cards.
-
Product
Minority Carrier Lifetime Tester
HS-CLT
-
HS-CLT Minority Carrier Lifetime Tester has strong functions. It can not only measure carrier lifetime of wafer but also silicon ingot, silicon filament,silicon phosphorus ingot,silicon boron ingot, seed crystal and other irregular shape silicon material.The minority carrier testing ranges from 1μs to 6000μs, the minimum resistivity is 0.1Ω.cm, (can be extensive to 0.01Ω.cm). Dynamic curve monitoring in the whole process.
-
Product
PCI Express IP
-
Rambus silicon-proven, high-performance PCI Express® (PCIe®) 6.0, 5.0, 4.0 and earlier generation digital controllers are optimized for use in SoCs, ASICs and FPGAs. These market-leading solutions for high-performance interfaces address AI/ML, data center and edge applications.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
-
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
Product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
Interface Card
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
Product
Mini-ITX SBC With Intel® Celeron® Processor N3350 & Pentium® Processor N4200, VGA, HDMI, LVDS, USB 3.0, PCI Express Mini Card Slot, M.2, And HD Audio
MANO310
-
*Intel® Celeron® N3350 & Pentium® N4200 (optional)*2 DDR3L SO-DIMM for up to 8GB of memory*1 PCI Express Mini Card slot and PCIe x1*4 USB 3.0 and 2 USB 2.0*1 SATA-600, 1 M.2 and 1 SDXC slot*6 COM supported*12 to 24 VDC*VGA, HDMI and LVDS with triple-view supported
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779066-01
Multifunction I/O
The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
PCI Express Analog and Digital I/O
826
-
Six advanced 32-bit counters Directly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement 16 analog inputs, 16-bit, 300 ks/s 8 analog outputs, 16-bit, 900 ks/s 48 digital I/Os with edge capture Watchdog timer, 3 stages
-
Product
2-slot Fanless Industrial System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, Front-access I/O, PCIe And PCI Slots
IPC962-512-FL
-
The IPC962-512-FL is powered by the 7th/6th generation Intel® Core™ and Celeron® processors (codename: Kaby Lake/Skylake) with the Intel® Q170 chipset. It is equipped with dual DDR4-2133 SO-DIMM slots with up to 32GB system memory. The ultra-compact industrial computer supports two swappable 2.5" HDDs; moreover, it offers flexible expansion options with one I/O module slot and two PCI/PCIe slots. It also has a wide operating temperature range of -10°C to +60°C and a 24VDC (uMin=19V / uMax=30V) power input for severe environments. According to the features above, this rugged IP40 industrial PC is a great choice for a wide variety of Industrial IoT applications including automatic optical inspection, digital signage, motion control, and factory automation.
-
Product
2 PICMG® CPU, 4 PCI™, 3 ISA Slots Backplane
HPCI-8S4
Backplane
- Supports AT, ATX power supplies- Slots: 2 PICMG® CPU, 4 PCI™, 3 ISA- Segment: 1- Dimensions: 264.2 mm x 218 mm
-
Product
PCIe-6321, PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781044-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6321 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6321 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI High Voltage MUX
50-350-001
Multiplexer Module
The 50-350-001 is a Short PCI Card designed as a high voltage multiplexer for use in a Submarine Cable Testing Application. It is designed to allow the dynamic connection of various test instruments to 1 of 16 test points. The multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.
-
Product
PCI 2 Amp Multiplexer, Single 16-Channel, 2-Pole
50-635A-102
Multiplexer Module
The 50-635A-102 is a single 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express Ultra-fast Data Acquisition Add-In Cards
-
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 102kΩ
50-297-040
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI-6154, 4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device
779340-01
Multifunction I/O
4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device - The PCI‑6154 is a simultaneous-sampling, channel-to-channel isolated DAQ device. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. You can combine the channel‑to‑channel isolated analog outputs to generate signals greater than ±10 V (up to ±40 V by combining all four channels). The PCI‑6154 is ideal for a variety of applications including automotive test, industrial monitoring and control, and high-speed continuous data logging. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Interface Board for Conduction Cooled PCI Mezzanine Card Systems
EXC-708ccPMC
Interface Card
The EXC-708ccPMC is an ARINC-708 /453 interface board for conduction cooled PCI Mezzanine Card systems. The board supports two or four ARINC-708 /453 channels. Each of the channels can be programmed either as transmit or receive. Each channel implements an 8K×16 FIFO and supports polling and / or interrupt driven operation.The EXC-708ccPMC comes complete with C-driver software library including the source code.
-
Product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-3
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (3 meters).
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 1.81kΩ
50-297-122
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI-5124, 150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device
779171-01
Oscilloscope
150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device—The PCI-5124 high-resolution oscilloscope device has two channels that sample up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI Express Serial Boards
-
Sealevel PCI Express serial boards utilize 120-byte FIFOs for maximum reliability in data-intensive applications. Software developed for standard PCI boards will also work with Sealevel PCI Express boards, simplifying your transition to this next-generation PCI bus. Sealevel PCIe serial boards are configurable for RS-232, RS-422, and RS-485 electrical interfaces. These PCIe serial boards are fully compatible with X2, X4, X8, X16, and X32 PCI Express slots.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCIe-to-MXM adapter supporting ADLINK Mobile PCI Express Modules with NVIDIA® Quadro® embedded GPUs
EGX-MXM-AD
-
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
2-port/4-port PCI Express GigE Frame Grabber Card
AX92320
-
The AX92320 supports PCI Express x4 lane, two or four independent Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports and GigE Vision camera compliance. The PCI Express x4 frame grabber can provide up to 30 watts at 54 VDC power to port which allows power to be supplied to connected PoE-based devices, such as GigE Vision cameras in machine vision systems. The intelligent GigE Vision card also supports IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition. Combining IEEE 1588 and PoE function, the card utilizes a single Ethernet cable for power, data, and synchronization. Furthermore, it supports jumbo frames up to 9.5KB. The AX92320 is ideal for PoE applications such as automated optical inspection (AOI), factory automation, and PC-based surveillance systems.
-
Product
14 bit, 125 MS/s PCI Digitizer
ATS460
-
ATS460 has been designed from the ground up for OEM applications, which require very high reliability, high performance, high quality and reasonable prices. ATS460 uses COTS analog components and FPGAs to provide you more features and benefits and at the same time reduced manufacturing costs without compromising quality. The result is that you get more digitizer for less money.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
PCI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
50-635A-104
Multiplexer Module
The 50-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
