Processing
Manipulates and analyzes a signal.
-
Product
Sulfur Analysis System
Model 6400TSG
-
Teledyne Analytical Instruments
The 6400TSG series utilizes our field-proven ultraviolet (UV) fluorescence technology to continuously monitor the total sulfur content found in process gas and liquid feeds. UV-Fluorescence is a non-consuming method of detection, eliminating the hassles associated with replacing tape cartridges, and enables detection as low as 10 ppb, depending on application, with stable, reproducible results.
-
Product
Spray Fluxer Pattern Uniformity
Fluxometer
-
Improve Process Quality - Eliminate guesswork when it comes to managing the consistency of flux application during wave soldering. Ordered in the same width as your WaveRIDER pallet, the Fluxometer rides the finger conveyor through the fluxing stage, conveniently and accurately rendering proof of a tuned spray fluxer. So easy to use, operators can perform diagnostic checks in minutes.
-
Product
High Temperature Digital Mass Flow Controller
SEC-8000 F/D/E Series
-
The SEC-8000F/D/E series can operate in high temperature environments, from 15 ℃ to 120 ℃, for a variety of tasks including semiconductor and compound semiconductor processing.
-
Product
PXIe-7820, Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module
783484-01
-
Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module—The PXIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7820 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Measurement, Communications & Testing
-
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Mechanical Test Head Housing
-
a result of more than 10 years' experienceavailable with integrated manipulatorfully integrated docking and board lockingtest housing mechanics design as per customer specificationssuitable for individual and high-volume productionstandard and customized dimensionsno limitation in size and electrical power capacitiesquick and easy locking and unlocking process for board changelarge application space load boardoptional number of channel boards as per customer specificationsfamily/DUT board connection achieved by high-end double-ended spring probes - 50 Ohmhigh-end cooling fansfacilitated adaptation with all available manipulator solutionsdocking design in compliance with customer internal docking standards/dimensionsdocking force as per customer specificationscenter of gravity fully compensated
-
Product
RF Power Sensor Solutions
-
Bird provides innovative power sensor solutions for all types of RF applications. From simple directional power sensors for the measurement of transmitter output power and VSWR measurement and monitoring applications, to highly accurate self correcting power sensors for process control applications, you can rely on Bird sensor products to meet the needs of your unique applications.
-
Product
Subsea Oil-In-Water Analyzer
-
The Mirmorax Oil-in-Water analyzer is based on an ultrasonic measurement technique in which individual acoustic echoes are characterized using advanced signal processing.
-
Product
Warm-Up Board
WECO 9000
-
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
Product
Temperature Input Module For Remote I/O
-
The Temperature Input Module for Remote I/O features a features a thermocouple input range of ±100 mV and a voltage input range of ±5 V. It also has an adjustable filter time for improved measurement quality and optional external CJC or PT100 RTD measurements.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Temperature Input Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
Express Analyzer
MAYA Express
-
Lyncis Express Analyzer was developed to answer the need for fast and reliable material chemical composition analysis. The application is valued by the clients where modern agile manufacturing metrology being applied and quick assessment of material is necessary to adjust critical process parameters without waiting on the lab results.
-
Product
Endpoint / Chamber Health Monitor based on Optical Emission Spectroscopy and MWL Interferometry
EV 2.0 Series
-
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
Product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
-
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Process Counter
CT6000
-
Full-logic control process counter.• Displays process, batch, total, and rate• Optional relay outputs and/or 4-20 mA analog output• Completely field adjustable• Full diagnostic functions• 3 programmable transistor setpoint outputs and inputs• Bi-directional counting• 115, 230 VAC (50-60 Hz) and 10-30 VDC power options
-
Product
Ultra-thin Mass Flow Controller
DZ-100
-
The DZ-100 inherits the same CRITERION™ technology—a differential pressure detection system for laminar viscous flow ranges—used on HORIBA STEC’s MFC, the D500. This innovative technology controls the mass flow of various gases with high precision. As with the D500, the user-configurable DZ-100 supports multi-range and multi-gas applications. The compact design of the MFC reduces the internal volume of the internal gas flow path, and the optimized control algorithm improves response characteristics. It uses a compact CPU with high processing capacity, and the piezo drive circuit and control CPU are installed in the MFC module while the power supply components are housed in a separate small control box. Up to four MFC modules can be controlled by connecting them with the dedicated miniature connectors.
-
Product
Digital Accelerometer
ZET 7151
-
The characteristics of the primary transducer are set in the device memory and measurements are performed based on those parameters. Thus, the digital sensors releases the user from setting the measuring channels and data processing. The sensors are fixed on the measurement object while the information transmission units are mounted in electric cabinets. An advantage of the ZETSENSOR units is easy installation and uninstallation as well as indication of feed and signal transmission which, in its turn, facilitates diagnostics of the system at the facility.
-
Product
Signal Conditioners
SC-1300
-
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
-
Product
PICMG 1.3 Half-size CPU Card With LGA1150 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q87, SATA3, USB 3.0, DVI-I/LVDS And Dual LANs
SHB230
-
The SHB230 is high-performing PICMG 1.3 half-size single board computer.The SHB230 based on the Intel® Q87 PCH is designed to support 4th Generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Haswell/Haswell Refresh) in the LGA1150 socket.The slot CPU card is equipped with two DDR3-1333/1600 SO-DIMM sockets with up to 16 GB memory capacity to meet customers needs.The PICMG 1.3 specification brings advantages of PCI Express to this single board computer that offers four PCIe x1 or one PCIe x4, and one PCIe x16 routed to the backplane.The onboard two SATA interfaces support RAID 0/1 functions to ensure reliable storage for multiple applications.Utilizing with the latest Intel® technologies, this PICMG 1.3 system host board is an ideal solution for DVR, medical equipment, industrial automation, process control, and network security market.
-
Product
Process Analytics
-
PAC offers a full range of on-line instruments for distillation, sulfur/nitrogen, viscosity, flash point, and reid vapour pressure (RVP) analyses by recognized PAC brands Antek, ISL, PSPI, and Cambridge Viscosity. These brands have long histories of providing innovative, highly dependable, and exceptionally accurate instrumentation.
-
Product
Metrology System
Aspect
-
Memory density increases with both layer-pair scaling and tier stacking for memory stacks well over 200 pairs. The Aspect metrology system was designed with these future architectures and scaling strategies in mind. Aspect metrology is demonstrating performance superior to X-ray systems across multiple customer devices through a revolutionary infrared optical system providing full profiling capability to enable critical etch and deposition control, with the speed and process coverage that customers require.
-
Product
MIPI Total Display IP Solution
DSI
-
The Arasan MIPI Display Serial Interface (DSI) Controller IP provides both device and host functionality. Additionally, the DSI Controller provides a high-speed serial interface between an application processor and display and follows a rigorous verification methodology to ensure interoperability of our DSI digital controller with our D-PHY analog IP. Arasan’s DSI solutions are MIPI standards-compliant and are designed to accelerate integration, lower risk and accelerate time to market for developers of display applications. Arasan’s expertise is backed by our unique silicon proven design discipline and product development process that ensures fast silicon success with our analog and digital IP.
-
Product
Position Sensors
-
A Position sensor is any type of device which detects the movement of a chosen object in either a Linear or Rotary motion and converts the movement into output signals which are suitable for processing, transmission or control depending on the application.
-
Product
Radar solutions for mechanical engineering
-
With OndoSense radar sensors you will increase the productivity of your industrial systems, reduce unplanned maintenance times for your machines and automate the work processes in the Industry 4.0.
-
Product
Semiconductor Inspection (SEMI)
-
A process for detecting any particles or defects in a wafer.
-
Product
Software
ExpertPower
-
ExpertPower™, a comprehensive energy management software, provides a suite of solutions: from billing, monitoring, BI, energy efficiency and demand response to in-depth Power Quality analysis and support of core planning and forecasting processes of independent power producers.
-
Product
Infrared Microscope
DDR200/300 NIR
-
The McBain DDR200 NIR (for 200mm) and DDR300 NIR (for 300mm) provide high-speed defect detection and precision measurement on wafers and other parts. These cost-efficient systems offer unique advantages for both production and process development use, providing an optimum near-infrared (900-1700nm) solution when both subsurface defect detection and dimensional metrology are required.
-
Product
Wheelset Axle Identification Using 2D DMC Codes
-
Automation of the process of identifying the axles of wheelsets at the site of the final inspection by the two-dimensional codes applied to them. The system should provide automatic search, reading and recognition of a two-dimensional code punching on the axis. The recognition result should be automatically transmitted to the ultrasound diagnostic unit as an identifier of the controlled object.
-
Product
Process Spectrometer
QualitySpec® 7000
-
Analytical Spectral Devices, Inc.
The QualitySpec® 7000 process spectrometer is ideal for measurement of process materials transported on conveyance systems. The system is designed for continuous measurement of solids, powders and blended materials, providing multiple measurements from a single point.
