-
Product
Dynamic Torque Sensing System
-
Advanced Telemetrics International
Are utilized in applications where conventional rotary torque transducers are not practical due to excessive shaft speeds, vibration, and dirty, oily environments.
-
Product
Quadrature Position & Rate Meter
-
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
Product
Ultra-Thin Telemetry Collar
-
Advanced Telemetrics International
The Ultra-Thin Telemetry Collar houses all of the electronics needed to provide a precision radio frequency link from sensors mounted on rotating shafts to stationary data acquisition and display instruments.
-
Product
Rotor Tester
SL Series
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
-
Product
Rotary Motion Logger Sensor
NUL-226
-
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
Product
Tungsten Probe Tips
T-4 Series
-
T-4 tips are for use in most standard commercial micropositioners for probing integrated circuits, pads, or lines. Each T-4 tip uses the same 10, 22, 35, 60, or 125 micron diameter tungsten wire as our Model 12C Picoprobe, but is mounted to a 0.020 inch diameter, 2 inch long tinned copper shaft.
-
Product
Closed-Loop Motor Controller
MS320
-
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
Product
Synchro/Resolver to Digital Converters
-
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
Product
Terminal Blocks with System
-
The Phoenix Contact terminal blocks enable a high degree of flexibility in terminal strip design. Choose between various connection technologies and combine the terminal blocks by installing bridges in the double function shaft. The terminal block system features standardized bridging, marking, and test accessories.
-
Product
Absolute Optical Encoder Kit Version
A2K
-
The A2K absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2K reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
Field Balancing Software
DS-0227A
-
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
Product
High-Capacity Cylindrical Shaft Gage
1200-HC
-
For higher capacity requirements, the 1200-HC delivers exceptional accuracy and repeatability, powered by the same trusted laser interferometer technology as the 1200-LX but with a 52-86% larger swing diameter. With five models available to suit various shaft lengths and weights, the 1200-HC can accommodate shafts up to 4,572 mm (180 inches) in length and weighing up to 1,814 kg (4,000 lbs). Refer to the specifications for detailed model information.
-
Product
Shaft Speed Sensors - Magnetoresistive
1102 / 932 / 933 XP
-
Features• Square-wave pulse frequency output, NPN open-collector• Zero speed operation with no signal loss• 5-24 VDC powered• 1/2" NPT conduit port (933 XP)• Non-contact, large gap distance sensing• Simple to install and set up• Works with Electro-Sensors magnetic pulser discs / wraps• 1102 – non-threaded stainless steel
-
Product
Rotary Torque Transducer
M425
-
M425 rotary torque sensor with keyway shafts offers high accuracy of 0.1% and torque measurement range from 0-10Nm up to 60,000Nm as standard. It’s an inline rotation torque transducer, widely used for motor, gearbox and pump torque testing.Using a highly-accurate non-contact technique, the Datum M425 Rotary Torque Transducer and Torque Meter represent an ultimate torque sensor for anyone looking to measure torque, power, and speed with high accuracy and repeatability.
-
-
Product
Inductive Motor Control
-
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
Product
General Purpose Probe
HT-1
-
HT-1 ''Workhorse'' General Purpose Probe - designed for temperature measurement of liquids, gases and semi-solids. Plastic handle with straight 3'' stainless shaft. Not good for surface temperatures. Maximum temperature 400°C, Time constant 0.5 Seconds. 5 foot lead. Not isolated.
-
Product
Rectal Probe For Rats
RET-2
-
• Smooth ball tip. Stainless steel shaft - 1'' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds. Not Isolated
-
Product
Rotary Switches
-
Reliability and ruggedness are just two of Elma's core competencies for rotary switches and encoders. Panel and shaft sealing up to IP68 against dust and water are standard for all rotary switches. The shaft material for all switches is stainless brass or stainless steel – this is suitable for rugged environments. In order to guarantee years of undisturbed functionality and service life of the rotary switches, all electronic contacts are plated and provided with hard gold. In addition to a large selection of encoders, coding switches, selector switches, audio solutions and multifunctional rotary switches & encoders, Elma Electronic offers you also the right knobs and caps.
-
Product
Tool Positioner Balancer
-
The Mini 31 balancer is a small, lightweight tool positioner that allows tools to be positioned over a work area for comfortable operation. The tool will remain at whatever level or position that it is left at. The operator can set the desired tension rate by simply placing a screwdriver into the slotted shaft and turning clockwise to increase tension and counterclockwise to decrease tension.
-
-
Product
Encoders
380 / 470 Rotary Shaft Encoders
-
The 380 Encoder is a standard industrial grade encoder available with single channel or bi-directional (quadrature) output. The 470 Heavy Duty Encoder provides a bi-directional (quadrature) output with an index pulse.• Square-wave frequency output• NPN open-collector and line driver (470) options• 5-28 VDC powered
-
Product
Brakes
-
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
-
Product
Tachometers
-
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine. The device usually displays the revolutions per minute (RPM) on a calibrated analogue dial, but digital displays are increasingly common.
-
Product
Immersion Probe For Liquids
DPT-24
-
DPT-24 Immersion Probe for Liquids - 24'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
Product
Tachometers
-
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
Product
Rotating Ring Disk Electrode
RRDE-3A
-
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
