-
Product
Flame Detector
SMC 3100
-
The SMC 3100 Series Flame Detector utilizes a tri-spectra design (UV, IR and visible light spectrums) to provide continuous and reliable flame detection. The 3100 Series design provides the ability to detect flames from both hydrocarbon and non-hydrocarbon sources, making it ideal for a facility where the flame source could be generated from a variety of gases.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Hand Held Needle Detector
UI-G60
-
Hand held needle detector, using the principle of magnetic field, can accurately detect the specific location of ferromagnetic metal impurities such as broken needles, which is very suitable for the inspection of thin and small items. It is also suitable for the detection of large needle detectors. It can accurately find the position of steel needles or ferromagnetic metals in a small range with this hand-held needle detector, avoiding the damage of metal impurities to consumers and manufacturers, and improving the quality of enterprise products.
-
Product
Needle Microprobe
MT-23/5HT
-
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Integral Intelligent Flame Detector
FS-100
-
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
Product
HVUL2 Horizontal Vertical Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVUL2 Horizontal Vertical Flame Chamber is designed for the flammability testing of plastic materials used in consumer electric devices and appliances per UL94. The chamber is constructed of stainless steel with a black interior and large sliding window for easy viewing. The HVUL2 includes a fully adjustable specimen support and a precision metered gas burner. Three digital timers with remote control are mounted on the inside back wall of the chamber, allowing for precise and simplified line-of-sight operation.
-
Product
Needle Microprobe
MT-23/3HT
-
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Needle Microprobe
MT-4
-
Fast-response 29 gauge needle probe with blunt tip, (needle length is 1cm) for instant readings. Good for instant skin temperature and surface temperatures, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
UV/IR Flame Detector for Hydrogen Apps
-
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
UV/IR Wet Bench Flame Detectors
SMC 3200/3300
-
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
-
Product
Needle Microprobe
MT-26/4HT
-
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Flame Photometers
-
Flame Photometer applies the emission spectrum as the basic principle, which uses the flame heat and excites part of the atoms in alkaline earth metal. The atoms receive energy and transfer it to the old energy level. When the atom is at a normal energy level it releases the energy.
-
Product
Masks Flame Retardant Performance Tester
WKS-1208
-
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
OptiStroke™ Needle Stroke Detection System
-
The patented OptiStroke system reduces product waste and confirms hot melt adhesive dispensing performance by verifying valve actuation and fatigue. Ideal for applications where product-yield loss is critical, the system is compatible with Nordson Universal™ modules, Speed-Coat™ modules and Harmony modules.
-
Product
Needle Hydrophone
HNP-series
-
The HNP needle hydrophone is the de facto standard for doppler mode measurements offering a flat response and wide directivity.
-
Product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
-
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
Product
Needle Microprobe
MT-D
-
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Palladium Alloy & Beryllium-Copper Probe Needles
-
Advanced Probing Systems, Inc.
APS has been providing high precision, high volume Tungsten Electrosurgical Needles for over 20 years in Colorado where the product was invented. Our unique Chemical machining process can produce polished electrosurgical needles for diameters from .177mm to .711mm. Overall lengths produced from 25.4mm to 38mm. Tip sizes range from .001mm to .115mm.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
