Product

Ampworx Hi-Gain Series Preamp Pedals

-

TC Electronic A/S

TC Electronic A/S

From classic rock tones to thunderous low-end punches, we're proud to present three exceptional beasts that capture the essence of three iconic amps. The AMPWORX HI-GAIN Series are preamp pedals built to celebrate the rich legacy of guitar-driven rock. Using our Ampworx component-based modelling technology, we meticulously replicated the unmistakable guitar tone of three amps in three separate compact stomp boxes. The overall idea is simple: One amp, one pedal. Buckle up and prepare for a sonic journey honoring the past while paving the ground for new high-gain horizons!

Product

SOIC and SOJ-to-DIP Adaptor

Series 35000X

-

Aries

Series 35000X - Aries

SOIC & SOJ to DIP Adapters. A cost effective means of upgrading to SOJ or SOIC...without changing your PCB layout.

Product

CLAMP ON CTS

P50

-

Beijing GFUVE Electronics Co.,Ltd.

P50 - Beijing GFUVE Electronics Co.,Ltd.

The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.

Product

JR-1

12820

-

M. C. Miller Company

12820 - M. C. Miller Company

• 35 Amp relay [@ 24VDC max. or @ 48VAC max.]• Crystal controlled timing• Rechargeable battery• Immediate or delayed interruption operation• Low battery indicator• Countdown and relay status indicators• On and off cycle times up to 999.9 seconds• Synchronized operation with any number of JR-1's and JR-2's

Product

Automated Leakage Current Tester

LINECHEK® II Series

-

Associated Research

LINECHEK® II Series - Associated Research

Our LINECHEK II Leakage Current Tester is designed for medical device manufacturers. With a feature set built around maximizing the efficiency of the Leakage Current test, LINECHEK II satisfies medical application requirements demanding up to 40 Amps of continuous line current. Use it on the bench or in a rack, from the front panel or via a PC interface to ensure your medical device is ready for global deployment.

Product

Low Noise Op Amplifiers (≤ 10nV/√Hz)

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.

Product

Power and Energy Automated Calibration System

RS-933

-

Radian Research, Inc.

RS-933 - Radian Research, Inc.

The RS-933 Syntron Power and Energy Automated Calibration System calibrates a range of test equipment including; Energy Reference Standards, Digital Multimeters, Phase meters, Energy meters, Power meters, Revenue meters, Amp meters, Panel meters & Power Quality meters.

Product

Metered Power with Audible Alarm (14) 5-15R 1U/0U V/H

EPS-1415-HVA

-

ELMA Electronic, Inc.

EPS-1415-HVA - ELMA Electronic, Inc.

EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter

Product

Instrument Mainframe

PI-11006

-

Pulse Instruments

PI-11006 - Pulse Instruments

The PI-11006 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.