Voltage Current Sources
See Also: Current Sources, Voltage Sources
-
Product
High Current Short Circuit Loop Impedance Meter
AMZC-310S
-
Measurement of very small short-circuit loop impedances (with resolution of 0,1mΩ) using the current of 150A under 230V, maximum 280A under 440V, or measurement using the current of 23A under 230V, maximum 42A under 440V
-
Product
High Current Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Product
High Voltage Probe: Single-Ended
-
A high voltage single-ended probe is typically used for measuring ground referenced signals up to 40 kV. However, some single-ended probes are designed for oscilloscopes with isolated or floating inputs for measurements that are not ground referenced. Users should select probes with a low input capacitance specification (< 4 pF) to minimize the probe’s loading effect on the circuit because a probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
Product
PCI High Voltage MUX
50-350-001
Multiplexer Module
The 50-350-001 is a Short PCI Card designed as a high voltage multiplexer for use in a Submarine Cable Testing Application. It is designed to allow the dynamic connection of various test instruments to 1 of 16 test points. The multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.
-
Product
PXI Source Switching Module
40-618A-001
Switch Module
The 40-618A PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module.
-
Product
Linear Voltage Regulators
-
ST offers a wide range of voltage regulators intended for automotive applications.
-
Product
Through Hole Type AC Current Sensor
CTF-100B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of feeder cable.*Measuring range:AC 1A～100A.
-
Product
Integrated Two-Stage Current Sensors
-
If ultra-low noise performance is required, our integrated two stage devices are the number one choice. With input inductances from 24 nH to 1.8 µH and a flux-noise level as low as 0.8 µPhi0/sqrt(Hz) an energy resolution of about 45 h is attained. The devices consist of a 16 SQUID series array as amplifier stage and a single front-end SQUID.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
Multiplexer Module
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
Medium Voltage Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Optimize your medium voltage power systems with our Container Load Banks. Engineered to perfection, these load banks offer advanced features and robust performance, ensuring accurate testing and maximum reliability. Unleash the power of excellence.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-216-HI
Programmable Resistor Module
The 40-230-216-HI (PXI) and 42-230-216-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
DC Voltage Data Loggers
-
This data logger can measure and store 4~20mA DC current readings automatically. The professional applications can be provided by the PC software DGraphTM. Logger status, alarm indication and low battery indication are via flashing red/green LED and yellow LED. The button on housing can be used to start logging, or confirm and clear LED alarm when LED alarm is hold status.
-
Product
Programmable AC Power Source
Model 8600 Series
-
- Compact size and light weight, standard 19″ rack construction- Step-less frequency setting from 45 to 450Hz- Very low distortion sine wave output- Output voltage range selectable 135 or 270V AC- Galvanically isolated input/output- Independent on/off switch for input and output- 16×2 vacuum florescent display for parameter display- Complete operation through push switches and a digital rotary encoder- Automatic protection against overload, short circuit and over temp.- Built in PFC to provide 0.99 input power factor and wide input range- Conforms to EN55022, class A, safety standard EN60950
-
Product
Split Core Current Transformers
LZCK-55
-
Beijing GFUVE Electronics Co.,Ltd.
Outdoor waterproof current transformers are applicable for AC power system 35kV and measurement of current of power supply equipment below 10KV also can be used for microcomputer protection. This type of current transformer employs imported silicon steel which with high permeability as magnetic material, has the characteristics of Small magnetic circuit loss and can be split, its semicircular core and secondary windings employ high quality epoxy resin vacuum, casting in plastic-case(ABS or PC) which is flame retardance anti-moisture, stable performance, no maintenance.
-
Product
Three Phase Secondary Current Injection Test Set
TEST-330B
-
Beijing GFUVE Electronics Co.,Ltd.
Three phase secondary current injection test set is testing relay set, protective device, instruments, output ac dc current and voltage source, embedded Window XP system.
-
Product
Millimeter-Wave Noise Source, Q-band, 33 To 50 GHz
Q347B
Noise Source
The Q347B waveguide noise source (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices...
-
Product
3,000 AMP PORTABLE POWER SOURCE WITH JUMP START FUNCTION
Part No. VERSAPRO3
-
Shanghai Beha Electronics Co., Ltd.
*Multi-function portable power you can take anywhere*Designed to jump start cars, trucks, motorcycles, boats, ATV’s and more*Vehicle jump starting and device charging capabilities for all of your portable power needs
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Low Voltage Attenuator
2-20
-
Take advantage of excellent attenuators at a low price. These low voltage units have excellent microwave characteristics and are ideal as an inexpensive low voltage unit for use with our 142 series high voltage precision attenuators while still providing a very respectable and clean 20 ps output risetime.
-
Product
Eddy Current Flaw Detector
US-525M
-
United Western Technologies Corp
The US-525M multi-channel eddy current testing instrument is a rugged industrial rack-mounted instrument offering multi-channel testing, integral digital strip chart, as well as Ethernet control and data transfer to meet your in process testing requirements. This instrument offers up to eight channels, with a frequency range of 20 Hz to 10 Mz, a high signal-to-noise ratio, a bright 12-inch diagonal color LCD flat-panel screen, and data storage of 32 Gig. It offers input/output (I/O) capability, USB and Ethernet connectivity, as well as three discrete alarm gates with independent outputs per channel. for your on-line bar, tube, wire and specialty component testing needs.
-
Product
Standards Source Instrumentation
-
PXI Arbitrary Waveform and Programmable Function Generators as well as DC source cards and a precision standards module.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-331-HI
Programmable Resistor Module
The 40-230-331-HI (PXI) and 42-230-331-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-031-HI
Programmable Resistor Module
The 40-230-031-HI (PXI) and 42-230-031-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage 9-Pin D-Type Connector & Cable Accessories
-
The High Voltage 9-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltageconnector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-132-HI
Programmable Resistor Module
The 40-230-132-HI (PXI) and 42-230-132-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Basic AC Power Source, 1000 VA, 310 V, 5 A
AC6802B
Power Supply
This basic AC power source offers stable, reliable power up to 1000 VA. An intuitive user interface and flexible I/O connectivity. Increase your uptime with stable, reliable AC power source Engineer reliability into your designs with a basic AC power source. Test your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikes. Easily access setup and measurement information
-
Product
High Voltage Test Sets
-
Nmc's high voltage test sets are manufactured as per the customers requirement ranging from 5kv-100kv ac or dc.
