-
Product
EMC Test Systems
IEC61000
-
N4L are the only IEC61000 EMC test system manufacturer in the world* with an on site UKAS ISO17025 calibration laboratory offering accreditation to IEC61000-3-2, IEC61000-3-3, IEC61000-4-7 and IEC61000-4-15. Calibration and trace-ability are a vital aspect of any EMC test solution and the coverage provided through N4L’s UKAS Laboratory is comprehensive. N4L’s IEC61000-4-15 calibration procedure is particularly noteworthy as it covers the entire test protocol detailed in Annex C of IEC61000-4-15. It is commonplace for specific parameters within IEC61000-4-15 (d parameters are frequently omitted from calibration procedures) to remain untested during typical flicker calibration due to the difficulty in providing trace-ability for such measurements. All tests within the test protocol of Annex C are included within the scope of accreditation and calibration procedures at N4L.
-
Product
Environmental Testing
-
D.L.S. Electronic Systems, Inc
D.L.S. Conformity Assessment provides testing services for environmental tests under its accredited ANAB/ACLASS ISO 17025 program. This globally accepted accreditation covers environmental and mechanical testing that include vibration and shock, temperature extremes , sand and dust, fluid and chemical resistance, altitude, humidity, salt spray, ingress protection, icing, flammability and other related testing services.
-
Product
Volume Calibration
-
Trescal provides full Volume Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Volume Calibration services can be delivered at your site or at our lab. Accreditations for our volume calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Mass Calibration
-
Trescal provides full Mass Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Mass Calibration services can be delivered at your site or at our lab. Accreditations for our mass calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Automated AC Digital Hipot Tester
-
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
Product
Velocity Calibration
-
Trescal provides full Velocity Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Velocity Calibration services can be delivered at your site or at our lab. Accreditations for our velocity calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
EMC Calibration
-
Trescal provides full EMC Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. EMC Calibration services can be delivered at your site or at our lab. Accreditations for our emc calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
IPv6 Testing and Certification
-
Our IPv6 testing services prove interoperability and functionality for IPv6 networks. Our testing includes coverage for IPv6 Host and Router, CE Router, IPv6 Applications and Network Protection Products. We offer ISO/IEC 17025 accredited testing for both the USGv6 and IPv6 Ready Logo test programs. In addition, customers may license our custom test tool IOL INTACT® for pretesting and internal validation.
-
Product
Sound Level Meter
SoundExpert LxT
-
The Larson Davis SoundExpert LxT Sound Level Meter is a full-featured meter designed for general product evaluation and noise monitoring applications. SoundExpert LxT comes with a graphic display and a fixed set of firmware options applicable for these applications. It is available as a general hand-held meter or data acquisition tool and also in a short-term noise monitoring kit. The meter expands upon the Larson Davis tradition of delivering value, innovation and function in a rugged, single-handed package, and is backed by our 2-year factory warranty, 24-hour application support, and accredited factory service/calibration.
-
Product
Product Safety Compliance Testing
-
Compliance with electrical safety standards and directives is a mandatory requirement worldwide. Our comprehensive NATA accredited safety testing facility at our Sydney Branch (since 1996) and the A2LA accredited Melbourne facilities at Keilor Park , provide a choice of NATA or A2LA accredited testing.
-
Product
RF Test Solutions
-
Peritec is accredited by the "RF and Wireless Specialty" (radio expertise and RF) from National Instruments (NI).The RF and Wireless Specialty, NI Alliance partners with expertise specialized design of radio frequency / wireless, authentication, automatic test, the high-frequency measurement is certified. Based on the track record and a wealth of expertise, Peritec, offers test solutions for RF / Wireless system.
-
Product
Prototype Measurement Services
-
On-site measurement service for prototype parts using laser tracker for large volume parts or portable arm CMM with optional laser scanning for smaller parts. Point cloud generation and full part modelling is available. API measurement services is an ISO 17025 certified organization, accredited by A2LA, our 3rd party prototype inspection reports provide the necessary confidence demanded by your customers.
-
Product
Calibration and Repair Services
-
Additel calibrations provide you with high confidence and low uncertainty for your standards. Our accredited calibration laboratory utilizes primary-level piston gauge systems and high-performance controllers to provide services for the entire Additel product line. In addition, our repair technicians which are ready to help, should you have trouble with the Additel units you own.
-
Product
Reference Thermometers
-
Our Reference Thermapen takes lab accuracy into the field. Each unit is factory calibrated at 5 test points and includes a UKAS accredited calibration certificate with test data. A true "system calibration" is performed matching its Platinum RTD sensor and the built-in electronics so all errors are included in the spec.
-
Product
Magnetic Calibration
-
Trescal provides full Magnetic Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Magnetic Calibration services can be delivered at your site or at our lab. Accreditations for our magnetic calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Energy Efficiency Testing
-
Intertek has the requisite accreditations, expertise and state-of-the-art testing laboratories around the world to help you meet energy efficiency requirements for global markets. Improving energy performance, developing clean and sustainable energy, and protecting the environment are key initiatives that all manufacturers must undertake if they wish to compete in today’s socially-conscious markets.
-
Product
Regulatory Testing
-
At Mobile Power Solutions, we’re focused on battery testing solutions. Our state-of-the-art lab and experienced engineering team are fully equipped to ensure your battery systems meet today’s rigorous regulatory requirements. We are ANAB accredited to ISO/IEC 17025:2017.
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Automotive
-
Radiometrics Midwest Corporation
A2LA accredited state of the art 10 meter, environmentally controlled, vehicle level, absorber-lined chamber is available to solve your EMC problems. Testing is performed on a 20-foot diameter turn table with a 25,000 pound capacity.
-
Product
Reference Temperature Sensors
-
AMETEK Sensors, Test & Calibration
Our reference sensors can be used as your daily working-reference sensors in laboratory or field calibration applications. A large selection of types are available, including; straight, 90 degree angle, 4 mm or 1/4”. The superior design and specifications combined with a long history of reliability and low drift have made the STS probes the working-standard in many EN/IEC 17025 accredited laboratories worldwide. The DLC sensors are a part of our patented Dynamic Load Compensation system.
-
Product
Production Measurement Services
-
Whatever you industry, product and production measurement requirement the API measurement services team are available to support your needs. ISO 17025 accredited, A2LA certified, API can supply manpower, equipment or both. The API team has experience across all manufacturing sectors and can support your short-term bottle-neck or longer term production measurement and calibration needs.
-
Product
Construction Materials Testing
-
Stanger Testing Services Limited has extensive UKAS accredited laboratories with analytical facilities for the assessment of chemical, physical and mechanical properties of construction materials. A comprehensive range of tests are available to evaluate the characteristics of a wide variety of materials and building components
-
Product
Electrical Standards
-
To verify the performance of an electrical calibrator or dc calibrator, you need an electrical standard. Fluke Calibration standards are found in primary calibration laboratories across the world. A wide range of electrical standards and frequency standards are designed to meet the needs of today’s laboratories for traceability and quality accreditation while also being portable, simple to use, and easy to support. Electrical standards include: Voltage standards; ac/dc transfer standards; ac measurement standards; resistance standards; ratio standards; current shunts.
-
Product
FCC Testing & Certification
-
F2 Labs can provide you with Federal Communications Commission (FCC) Certification in our EMC Testing Lab, Supplier’s Declaration of Conformity (SDoC), formerly Verification and Declaration of Conformity, testing. Manufacturers who sell electrical and/or digital products in the United States must have their products tested by an accredited lab certified by the FCC. F2 Labs is accredited by the FCC as a Conformity Assessment Body (CAB). We partner with a Telecommunication Certification Body (TCB) in order to provide our clients with FCC Part 15 certification and compliance testing & approvals.
-
Product
Torque Calibration
-
Trescal provides full Torque Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Torque Calibration services can be delivered at your site or at our lab. Accreditations for our torque calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Laser & LED Testing
-
Lasermet is the UK’s leading test house for testing to the following standards:EN 60825-1 / IEC 60825-1*EN 60825-2 / IEC 60825-2EN 60825-12 / IEC 60825-12*EN 60601-2-22 / IEC 60601-2-22*21 CFR 1040.10and is the only test house with UKAS accreditation for laser and LED testing (other than the National Physical Laboratories).
-
Product
Resistance Standards
-
Ohm-Labs manufactures reference grade resistance standards from 10 micro-ohms to 10 teraohms. Each range of standards utilizes the latest advances in materials and processing for high stability and immunity from changes in ambient environment. All products are supplied with ISO17025 accredited calibration.
-
Product
Laboratory Weathering
-
Atlas Material Testing Solutions
Atlas Weathering Services Group (AWSG) operates one of the largest networks of ISO/IEC 17025 accredited accelerated weathering testing laboratories in the world. With laboratories in the USA, Germany, France and the United Kingdom, AWSG's indoor exposure laboratories offer artificial accelerated weathering tests and a variety of other environmental test programs, all designed to accurately simulate true end-use conditions and meet global weathering standards. Atlas has several accelerated laboratories around the world.
-
Product
Chemical Calibration
-
Trescal provides full Chemical Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Chemical Calibration services can be delivered at your site or at our lab. Accreditations for our chemical calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
EMC Measurements
-
Immunity and emission measurements Kiwa Dare is an accredited test house that performs full compliant EMC measurements in the field of EMC legislation. All results are recorded and represented in reports which form the foundation on which clients can put the CE mark on their product. Besides that our tests are performed under accreditation for Automotive, medical, maritime, aerospace military and railway applications.
