-
Product
Emissions Testing
-
One of the main aims of environmental protection is to suppress harmful emissions or reduce them as much as possible. Typical examples of emissions include gaseous and particulate pollutants emitted by furnaces, odor emissions and particulate emissions from waste tips. Help protect the climate and ask us to measure the emissions created by your facilities.Our experts will test your facility – from large-scale firing plants to biogas plants, from waste incinerators to crematoria – according to national and international standards. We can also help you reduce noise pollution, measure exhaust gases and harmful emissions, and modernize your facilities.With their extensive experience, our experts can analyze your processes and identify potential improvements. As a measurement body registered throughout Germany and internationally accredited according to ISO 17025 we are authorized to perform the legally required measurements for you.Your facilities need testing? Ask us about our emission testing.
-
Product
Humidity Calibration
-
Trescal provides full Humidity Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Humidity Calibration services can be delivered at your site or at our lab. Accreditations for our humidity calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Automotive EMC Testing
-
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
-
Product
Product Testing
-
Cotton Electric Services, Inc.
Cotton Services is accredited through the National Association of Independent Laboratories (NAIL). Our Testing equiptment goes through a calibration process at least once a year and on-site tests are routinely performed by factory officials to ensure testing accuracy. Cotton Services Employees are certified in equipment maintenance and testing procedures. All products are tested at or above minimum test ranges set by the industry.
-
Product
EtherCAT Conformance Test Tool (CTT)
ET9400
-
The Conformance Test Tool (CTT) enables in-house testing of EtherCAT slave devices. The use of the CTT supports EtherCAT device development, helps to ensure conformance prior to device release and to prepare the device for the official, independent Conformance Test in an EtherCAT Test Center (ETC) accredited by the EtherCAT Technology Group.
-
Product
IP code Testing
-
Educated Design & Development, Inc.
Complies with various IEC, EN, CE, VDE, UL & CSA requirementsUnit comes with NIST traceable / ISO 17025 accredited certificate of calibration.ED&D is ISO 17025 accredited by ACLASS, an ILAC Member. Measurement data and uncertainty data is available.Uses RTS-01 Rain Spray Head
-
Product
Safety Testing
-
Mobile Power Solutions specializes in guiding your company through today’s increasing quagmire of battery-related safety regulations. MPS provides comprehensive regulatory compliance, safety, and performance testing; we are ANAB accredited to ISO/IEC 17025:2017.
-
Product
2-Port 18 GHz Analyzer
M5180
-
VNAs and ACMs are delivered with factory calibration certificates containing no data. The add-on option for ISO17025/Z540-1 Accredited, Traceable Calibration Certificate and Uncertainties is available and needs to be specified at time of order.
-
Product
Multifunction Field Calibrator & Communicator
MC6-Ex
-
The MC6-Ex is an intrinsically safe field calibrator and communicator. It is ATEX and IECEx certified and can be used in all hazardous zones / divisions. The MC6-Ex includes a field communicator for HART, FOUNDATION Fieldbus and Profibus protocols. Each calibrator is delivered with a traceable, accredited calibration certificate as a standard. t is a documenting, multifunction calibrator and communicator that offers calibration capabilities for pressure, temperature and various electrical signals.
-
Product
Force Calibration
-
Trescal provides full Force Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Force Calibration services can be delivered at your site or at our lab. Accreditations for our force calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
-
Product
Flow Calibration
-
Trescal provides full Flow Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Flow Calibration services can be delivered at your site or at our lab. Accreditations for our flow calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
LabVIEW & TestStand Software Development
-
We are proud of our heritage in quality software development. We have a growing, successful department of accredited, experienced LabVIEW and TestStand software and systems engineers which means you can benefit from our technical experience from the first day of your project.
-
Product
Accelerometry Calibration
-
Trescal provides full Accelerometry Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Accelerometry Calibration services can be delivered at your site or at our lab. Accreditations for our accelerometry calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Cupping Tester
PCE-CPT 20
-
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
Product
Laser Power Meter Calibration Services
-
Following the successful setup of our UKAS accredited laser testing laboratory we have now set up a calibration laboratory in our Bournemouth premises for the purpose of offering laser power meter calibrations. We are able to undertake NPL traceable calibration of laser power meters at any of the following wavelengths:
-
Product
Safety Testing
-
KTL Safety Group is fully accredited to meet the growing needs for worldwide safety testing and compliance and provides: Safety testing and certification of electrical and electronic equipment to international and European safety standards, Pre-compliance evaluations that identify problem areas early in the design stage, to reduce the need for potentially expensive modifications.
-
Product
Chemical Testing
-
Our modern and comprehensive Chemical Laboratory has been certified and registered in accordance with the Environmental Laboratory Accreditation Program (ELAP) and by the State of California Department of Health Services.
-
Product
RTCA/DO Testing
-
We have the facilities, accreditations, and experience to accurately and efficiently perform testing to a wide range of military and aerospace specifications, including the latest lightning tests.
-
Product
Hardness Test Blocks, Indenters & Accessories
-
Qualitest offer the largest Hardness Test Block selection in the industry. If you don't see what you're looking for, please call our sales department. All of our Hardness Test Blocks come with Certification. All the blocks are calibrated and accredited to ISO guide 25 and will meet automotive and aerospace standards. The HRC test blocks are calibrated on the new NIST level.
-
Product
FCC-Recognized Accredited Testing & Certification
-
Helping you ensure that your radio devices or devices with integrated wireless modules meet requirements to demonstrate compliance to FCC requirements for approval.Manufacturers planning to sell their wireless/RF products in the United States must ensure that their equipment won’t electromagnetically interfere with other products or cause harm to the public as enforced by the Federal Communications Commission (FCC), per Title 47 of Code of Federal Regulations (CFR).
-
Product
Product Safety Testing
-
D.L.S. Electronic Systems, Inc
D.L.S. Conformity Assessment is a fully staffed and accredited product safety testing and consulting organization within the D.L.S. corporate umbrella. The Conformity Assessment group offers full compliance testing services for North America, Europe, Pacific Rim, and other global regions including testing to these standards:
-
Product
Product Safety Testing & Certification
-
F2 Labs is a top, full-service product testing company. Our safety laboratory is set up to test/evaluate products for the United States, Canada, Europe, and International Certifications. Our safety facilities are A2LA Accredited, and our safety test data and evaluations are accepted by an OSHA accredited Nationally Recognized Test Lab (NRTL). Our experienced team of engineers can develop an efficient plan for addressing your product’s safety and work with you at our facility or yours to complete the product safety testing and certification.
-
Product
Temperature Calibration
-
Trescal provides full Temperature Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Temperature Calibration services can be delivered at your site or at our lab. Accreditations for our temperature calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Wireless Accreditations
-
MET Labs is a global leader in wireless testing with capabilities ranging from standard FCC & CE compliance to sophisticated cutting-edge programs like ZigBee.
-
Product
Load Cell Indicator
-
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
Product
LC Software
Total Solution for PIC/S and FDA Compliance
-
All Shimadzu network system products incorporate functions for the PIC/S GMP and the Part 11 compliance regulation, and computerized system validation functions required by GxP. Shimadzu provides documentation including IQ/OQ, Certificates of Compliance, and Inspection Test Result Reports based on Shimadzu IS09001 certified system. Shimadzu's accredited service personnel offer full support for validation of customer's Shimadzu products. In the latest information on PIC/S and FDA regulations through seminars and workshops, participating in vendor audits demanded by agencies, and actively assisting customers to comply with new regulations.
-
Product
Test Systems
-
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
Product
Medical Device Calibration
-
Trescal provides full Medical Device Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Medical Device Calibration services can be delivered at your site or at our lab. Accreditations for our medical device calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Railway EMC Testing
-
EMC Technologies is the only NATA accredited organisation for performing Track side testing of the whole train/tram. We can provide NATA accredited testing services to EN 50121-3-1, EN 50121-3-2, EN 50121-4 and EN 50121-5. This includes electromagnetic emission and electromagnetic immunity measurements. We can also provide testing and consultation for EN 50121-1 and EN 50121-2 .
