Electrostatic Discharge Simulators
create known values of electrostatic discharge.
-
Product
Electromagnetic Simulation Software
EmSlice
-
EMSlice is an EM Simulation Software tool supporting the design, analysis, testing and evaluation of systems involving EM Radiation. Including optical, radio communications, radar, antenna systems, etc.
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
-
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
-
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
Product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
-
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Partial Discharge Detecting Detectors
-
Hangzhou Xihu Electronic Institute
Including pulse current PD detecto, high frequency PD detector, transient earth PD detector, ultra high frequency PD detector, and ultrasonic PD detector.
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
-
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
Battery Discharge and Charge Tester
-
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
Altitude Data Simulator
ADS-100
-
The Model ADS-100 is an all solid-state device that simulates the output of altitude encoders/digitizers in both parallel and serial (RS232) data formats. Designed to substitute for an altitude encoder when testing and troubleshooting an aircraft's altitude reporting system, the ADS-100 provides two RS-232 compliant outputs in addition to the ICAO pressure altitude code.
-
Product
Power Amplifer AURORA Digital Interface For Simulator Application
PAV DIA01
-
PAV DIA01 is the optional accessory unit and Aurora digital interface for PONOVO’s power amplifiers which could convert the analog input signal into digital signal, supporting communication between power amplifier and simulators via AURORA protocol.
-
Product
Software to Simulate Large Area Semiconductor Devices
Laoss
-
Laoss (large-area organic semiconductor simulation) is a powerful software package for the design, simulation, and optimization of large-area organic and perovskite solar cells and LEDs (displays, lighting panels, photovoltaic arrays).
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
-
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Transducer Simulator
Model 0V
-
SPECIFICATIONS: Impedance: 700 ohms nominal. Output Ranges: 10 turn vernier 0 - 3mV/V. Excitation: 20v ac/dc max,
-
Product
Multi-Spool Network Simulation & Latency Solutions
Fiber Lab 750
-
from M2 Optics provides the perfect combination of flexibility and efficiency when requiring spools of fiber for testing, latency, and system demonstration applications.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
Finite Element Method Magnetics Simulation Software
FEMM
-
Finite Element Method Magnetics
FEMM is a suite of programs for solving low frequency electromagnetic problems on two-dimensional planar and axisymmetric domains. The program currently addresses linear/nonlinear magneto-static problems, linear/nonlinear time harmonic magnetic problems, linear electrostatic problems, and steady-state heat flow problems.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
4, 8 and 16 Channel ARINC429 Test and Simulation Module
ANET429-x
-
The ANET429-x is a member of AIM’s Ethernet based modules for analysing, simulating, monitoring and testing ARINC429 channels.
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
Vacuum Discharge Test Equipment
DAC-VD-1
-
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
Product
Circuit Simulation & PCB Design Software
TINA Design Suite
-
TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
PXI & LXI Simulation Tools
-
Our PXI & LXI simulation tools help you to accelerate the development process by simulating the product in your test system. These tools allow you to develop and test the system software independent from your application hardware. By using the tools, you can minimize the time required with the physical system.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
Altitude Simulation Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
Product
MEMS Sensor Simulation
SimSENSOR
-
Performance testing of sensor fusion in MEMS inertial and multi-GNSS navigation systems. SimSENSOR extends the capabilities of Spirent’s multi-GNSS simulators by simulating MEMS sensor outputs on a common trajectory with the simulated GNSS RF signals. The simulated MEMSs sensor outputs include user control of representative noise and errors (bias/drift).
-
Product
Photovoltaic Array Simulation Solution
-
The Keysight N8937APV and N8957APV photovoltaic array simulators are capable of testing PV inverters up to 1,500 V, enabling designers to participate in the recent industry shift to the higher voltage. They can quickly simulate I-V curve characteristics under different environmental conditions (temperature, irradiance, age, cell technology and more), enabling the user to quickly and comprehensively test their solar inverters.
-
Product
Electrostatic Field Meter Kit
PFK-100B
-
- Measure range & polarity of electrostatic fields in 1 volt or 10 volts increments- Charges from zero to over 1000 volts in less than 5 seconds- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Use with a datalogger to record measurements & create reports- Compatible with the Autoanalysis System- Accuracy of ± 5%- Battery Operated
