Electrostatic Discharge Simulators
create known values of electrostatic discharge.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
Seal Integrity Verification and High Altitude Shipping Simulator
SIV III
-
The SIV also has the ability to simulate shipping a packaged box of dry goods at high altitudes. The number of peaks, the heights of the inclines (or peak), the ramp speed (or rate), and the time at the peak are configurable through the controller.
-
Product
Electrostatic Fieldmeter
FMX-004
-
Simco-Ion’s Model FMX-004 Electrostatic Fieldmeter is a compact handheld electrostatic fieldmeter used for locating and measuring static charges. Its pocket size makes it handy to use and four-button operation makes it easy to operate.The FMX-004 measures static voltages within ±30 kV (30,000V) at a distance of 1 inch. Results are simultaneously displayed numerically and in bar graph format.
-
Product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Modular Solar Array Simulators
MP4300A Series
-
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Load Cell Simulator
-
A High-Stability adjustable Load Cell Simulator. It is specifically designed for Load Cell Fault and System Fault Diagnosis. It also provides a useful Development Tool for any System which relies upon Load Cells. The Output Signal is adjustable from -0.1 to +3.1 mV/V.
-
Product
Force On-Force Reactive Tactical Readiness IADS Simulation
FORTRIS™
-
FORTRIS™ is a scenario engine that provides a real-time complex battle simulation between hostile and friendly forces. The Synthetic Environment within FORTRIS contains a true multi-layered Integrated Air Defense System (IADS) simulation that can act and react both as an overall system, as well as individual contributors, making it the ideal cognitive training tool within the Live Virtual Constructive (LVC) world.
-
Product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
-
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
Product
Network Simulation and Load Testing
-
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
Product
20KV 30KV Electrostatic Discharge ESD Simulator
20KV/ 30KV Electrostatic Discharge ESD Simulator
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD-0230/ESD-0220 has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Sand Dust Climatic Environmental Simulation Test Chamber
CX-SC80
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand Dust Climatic Environmental Simulation Test Chamber
-
Product
Electrostatic Discharge
-
Our electrostatic discharge (ESD) measurement and control solutions include charge plate monitors, sensors, resistivity meters, and voltmeters. Reliably monitor, measure, locate, and test for static electricity.
-
Product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For PMC
AMCX429-x
-
ARINC429 Test and Simulation module for PMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
2 Port BRI-S/T ISDN Simulator
BRI-2ST
-
The most inexpensive ISDN simulator on the market. The unit has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Interference Simulation System
GSS7765
-
Combined with Spirent’s powerful GSS7000 or GSS9000 Series simulators, the GSS7765 interference generator creates the ultimate tool for testing against external jamming and unintentional interference. The GSS7765 enables you to create and generate custom waveforms, helping you to defend your systems against real-world threats.
-
Product
MIMIC® Cable Modem Simulator
-
MIMIC Cable Modem Simulator, is the industry's first integrated simulation tool supporting DOCSIS, allows cable modem developers and cable companies to perform real world, integrated cable and internetworking device simulations. MIMIC allows suppliers of cable modems to design, develop and test their products in a virtual and scalable network environment, assuring customers that their cable modems will work properly when deployed across heterogeneous environments. Cable providers can use MIMIC to simulate the 1000s of households that use cable modems to assure the scalability of cable management software. In addition, providers can also use MIMIC for large-scale Operations Support System (OSS) testing deployments in place of large banks of cable modems, which would be cost prohibitive.
-
Product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
PMC Module
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
NIBP Simulators
-
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
Product
Troposcatter Simulator
HTSS
-
Hollis Electronics Company LLC
Hollis Electronics HTSS is a quad diversity Troposcatter channel simulator which interfaces with your radio equipment at 70 MHz IF. The complete digital implementation provides high accuracy and exact repeatability. An integrated AWGN noise source coupled with an internal power meter supports accurate setting of SNR and Eb/No.
-
Product
Linktropy Network Delay Simulator
-
Linktropy Emulators Provide Affordable Network Emulation for Accurate, Repeatable Performance Testing at Speeds up to 1 Gbps
-
Product
IPX56 Simulation Rain Test Chamber
CX-IPX56A
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX56 Simulation Rain Test Chamber widely used in the lamps and electrical and electronic product certification testing institutions and for testing the waterproof of electrical and electronic products of shell protection level.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
