BER Test
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: BER Testers
-
Product
Adjustable ISI Channel Emulation Package for M8000 Series BER Test Solutions
M8070ISIB
-
Simplify receiver testing by offering unprecedented flexibility for handling test channels.
-
Product
Ethernet Tester
GAOTek Gigabit
-
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
Product
VITA 57.4 FMC+ HSPC Loopback Card
-
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Analog Noise Generator
PNG7000
-
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
Product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
-
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
Product
Test Solution Offering BER Testing
Eye-BERT Micro LR
-
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
Variable Attenuators
-
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
Product
Error Distribution Analysis Package For M8000 Series BER Test Solutions
M8070EDAB
-
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070EDAB Error Distribution Analysis package offers features like burst mechanism detection and analysis, frame loss ratio estimation and error mapping.For instance, you can easily estimate your FEC decoder margin or find the root cause of systematic errors by exploring the error map. The plugin also supports the use of real-time scopes as error detector.
-
Product
Bit Error Rate Testers
-
The FarSync BERT Tester provides a comprehensive, simple to use, line testing utility for asynchronous and synchronous lines. Standard BER test patterns are used with real time error counters, user controlled error injection, full line test statistics and APIs.
-
Product
Bit Error Rate Testers
-
The Tektronix BERTScope® and PatternPro® families provide a range of signal conditioning and BER test solutions from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry’s broadest serial communications test portfolio of Bit Error Rate Tester products.
-
Product
Advanced Measurement Package For M8000 Series Of BERT Test Solutions
M8070ADVB
-
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070ADVB Advanced Measurement package offers advanced features like automated jitter tolerance test and parameter sweeps, eye diagram measurement or the integration of external equipment such as electrical and optical clock recovery or error analysis using a real-time scope.
-
Product
Bit Error Ratio Testers
M8000 Series
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
Automotive Ethernet Rx Compliance Software
AE6910R
-
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
Product
Interactive Benchtop Test
-
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
NI Real-Time Test Cell Reference System
778820-35
-
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
NI Real-Time Test Cell Reference System
780590-35
-
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Application Software for Electronic Test & Instrumentation
-
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
Wireless Device Test
-
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
-
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Dielectric Test Fixture
16451B
-
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Bottom Electrode SMD Test Fixture
16197A
-
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
-
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
EOL/Functional Testing
-
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
Product
Functional Test Fixtures
-
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Radar Test System
UTP 5065
-
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Regenerative Battery Pack Test System
17040E
-
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
