Product

Battery Charger-Analyzer for small battery systems (up to 10A-Hr)

24-400xg

-

JFM Engineering

24-400xg - JFM Engineering

The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.

Product

SMB Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Pasternack SMB connector category has dozens of part numbers, most are RoHS and REACH compliant. SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB connectors are built to precise microwave and RF industry specifications. Connectors in the SMB series are manufactured in jack or plug gender with 50 Ohm impedance. SMB connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this SMB connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.

Product

HEV Battery Reconditioner

-

NuVant Systems, Inc.

NuVant Systems, Inc.

Battery reconditioning and cell balancing is a well understood process for NiMH batteries. The procedure was initially developed for NiCad batteries decades ago. NuVant Systems has simplified the process to bring electrochemistry to the streets. The EVc unit is a push-one-button-after-wire-up system for small shops to large vehicle operators.

Product

Connectors, Header - Female

INT-10140

-

Playing With Fusion Inc

INT-10140 - Playing With Fusion Inc

1x40 pin female header. These headers mate with square-pin 0.1" male headers. They can be cut into smaller segments, but please note that they are not break-away and at least one pin will be lost with each cut. Gold plated and RoHS compliant.

Product

Additional Products: 200 Pin D Connectors

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

Mini SMP Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Mini SMP connector series, also known as SMPM connectors, are ultra-miniature, high frequency connections commonly used in applications up to 65 GHz. Mini-SMP connector category will terminate to coax or PCB (printed circuit board) and many mini-SMP connectors are hermetically sealed. Pasternack mini SMP connectors are built to precise microwave and RF industry specifications and many are RoHS and REACH compliant. SMP mini connector products are built in male or female gender with 50 Ohm impedance. Mini-SMP connectors are available in straight or right angle versions, as well as, mountless options. These Mini-SMP connector designs include solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack are in-stock. Not only in stock, but these SMP mini connectors will ship the same day as they are purchased.

Product

Compliant Connectors

MIL-DTL-55302

-

Smiths Interconnect

MIL-DTL-55302 - Smiths Interconnect

High reliability 55302 compliant connectors with mixed signal, power and coaxial contacts designed for defense, commercial aerospace and space demanding applications

Product

CTEK Multi US 7002 Battery Charger

56-353

-

CTEK Power USA

56-353 - CTEK Power USA

The MULTI US 7002 is the ideal battery charger for your caravan, car and boat. The battery charger is well suited for all-year use. Thanks to its SUPPLY mode the battery charger provides power even without a battery. The SUPPLY mode is indispensable when changing the battery as you avoid losing complicated program settings.Perfect for vintage car, boats with one battery, boats with start & service battery, boats with start & service bank, scooter, motorcycle, Quad/ATV, lawnmower, caravan, and tractor.Includes two interchangeable connection leads, one with clamps, and one with eyelet terminals.

Product

Digital Battery Tester with Automatic Test

706

-

Electronic Specialties Inc.

706 - Electronic Specialties Inc.

Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.

Product

44-Pin D-Type Connector, Male, Right Angled PCB Mount

40-963-044-RM

-

Pickering Interfaces Inc.

40-963-044-RM - Pickering Interfaces Inc.

Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.

Product

Mating Coax Connector and 20 Coax Pins Crimped to 3' with BNC Connectores

GT96406

-

Marvin Test Solutions, Inc.

GT96406 - Marvin Test Solutions, Inc.

Mating coax connector and 20 coax pins crimped to 3 foot wires with BNC connectores

Product

Portable Connector End Face Geometry Interferometer

-

Thorlabs, Inc.

Thorlabs, Inc.

Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.

Product

Power Interface Board 6U, 2 PSU connectors

106PIBM602-0000R

-

ELMA Electronic, Inc.

106PIBM602-0000R - ELMA Electronic, Inc.

The PIB 6U 2 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.

Product

Battery & Electrical System Testing

12-0200

-

Associated Equipment Corp.

12-0200 - Associated Equipment Corp.

Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.

Product

5 ft Harness, 78-Pin Male Connector

GT96110

-

Marvin Test Solutions, Inc.

GT96110 - Marvin Test Solutions, Inc.

5 ft harness, 78-pin male connector on both ends

Product

Natural Cooling Input 380VAC 3 Phase to Output 190-300VDC 10A-40A Rectifier Battery Charger

SD230D20ZZ

-

Zhejiang Sandi Electric Co., Ltd

SD230D20ZZ - Zhejiang Sandi Electric Co., Ltd

SANDI “SD” series intelligent high-frequency switch power supply modules are specially developed to meet the demands of modern DC system. The charger rectifiers are designed with world leading patent technology “resonant voltage type soft switching power supply technology”. They feature high efficiency and stability, intelligent control, small size and light weight. Standard RS-485 interface, easy to connect with automation system. “Four remotes” functions, intelligent management. The products are widely used in power plant, substations and etc..