NVM Express
optimized register interface, command set and feature set for PCI Express (PCIe®)-based Solid-State Drives (SSDs).
-
Product
PXI Express Instrument
PXIe-FC4-DCE
-
Avionics Interface Technologies
Single PXI Express Instrument that is reconfigurable to operate as a PXIe-FC4 or a PXIe-DCE module. Save system slots with this instrument by getting both Ethernet (10/100/1000) and Fibre Channel in a single instrument in a single PXI Express Slot.
-
Product
PXI Express Host Systems
-
Avionics Interface Technologies
System configurations with 16 & 5 Instrument Slots AvailableOptions for Embedded Controllers, or Remote Control (via PCI Express)With Embedded Controllers
-
Product
PXIe-5114 , 125 MHz, 2-Channel, 8-Bit, PXI Express Oscilloscope, 64 MB
783591-02
Oscilloscope
PXIe, 125 MHz, 250 MS/s, 8-Bit PXI Oscilloscope—The PXIe‑5114 low-cost PXI oscilloscope has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth. The PXIe‑5114 also features advanced PXI synchronization and data streaming capabilities.
-
Product
PCIe Octopus Express 14-Bit Digitizer
Digitizer
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
Product
PCI Express Ultra-fast Data Acquisition Add-In Cards
-
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
Product
COM Express
-
COM Express defines standardized footprints and pin-outs for Computer-on-Modules. With the Revision 2.0, PICMG added the compact footprint (95x95mm) to the basic footprint (125x95mm) and extended the pin-outs being future-proof. New Digital Display Interfaces (DDI) and super-fast USB 3.0 are available. The new Pin-out Type 10 in COM Express Revision 2.0 supports perfectly modules in the COM Express mini footprint (84x55 mm).
-
Product
2/4-CH PCI Express® GigE Vision PoE+ Frame Grabbers
PCIe-GIE7x Series
Frame Grabber
- Hardware Trigger over Ethernet with Action Command- Up to 120W PoE power from PCIe bus/4-pin/6-pin Molex connector- PCI Express® x4 compliant- IEEE 802.3at for PoE+ (Power over Ethernet Plus)- PoE protection and automated power budget control for enhanced asset protection- Easy-to-use utility and API provided for PoE power management- Multiple cards, multiple cameras, in a single system- Wide operating temperature range from 0°C to +70°C supporting non-drop frame capture in extreme environments
-
Product
PCI Express 5 Base Specification Receiver Test Automation
N5991PB5A
-
The N5991PB5A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 5.0 ASICs
-
Product
Flexible x1 PCI Express to MiniPCI Adapter
SKU-067-0X
-
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PCI Express Digital I/O Cards
-
Sealevel PCI Express digital I/O cards are designed for computers with X1 PC Express slots and are compatible with any PCI Express slot. Digital I/O cards are currently available with optically isolated inputs and Reed relay outputs. Optically isolated inputs protect the PC from voltage spikes common to industrial environments while Reed relay outputs provide reliable, long-life switch closures suitable for low current applications.
-
Product
6-Port PCI Express
PEX 8724
-
The ExpressLane™ PEX 8724 is a 24-lane, 6-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8724 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI/104-Express Quad PCIe MiniCard Carrier
E104-MPE
-
The PCIe MiniCard carrier provides four PCIe MiniCard sockets on a PCI/104-Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
-
Product
Low Profile PCI Express 8-Port
7803e
-
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
33 lane, 9 port, PCI Express
PEX 9733
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-1
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (1 meter)
-
Product
Dual Port Fibre Channel End-System Module for PCI Express
PCIe-FC4-NIC
-
Avionics Interface Technologies
Dual port module, operates as a Fibre Channel network node with support for multiple upper layer protocols.
-
Product
PXI Express Board Virtex-5 DVI Transceiver
SMT739
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
PCI to PCI Express Adapter
SKU-011-01
-
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
Product
COM Express Type 7
-
One of the most fundamental innovations of the COM Express Type 7 pinout is the support of up to four 10GbE interfaces, essential for the next generation of edge node appliances. Type 7 modules are headless (no graphics), which is why they are also referred to as “Server Level COM Express”.
-
Product
x1 PCI Express System Timer
SKU-048-01
-
The x1 PCI Express System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The Timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the x1 PCI Express System Timer supports clock intervals ranging from 1ms to 64ms.
-
Product
x1 PCI Express Extender
SKU-006-01
-
The x1 PCI Express Extender was designed to support the development, debugging and verification of PCI Express boards. The Extender provides a complete PCI Express debugging platform that allows easy access to the logic signals, it has overcurrent protection and hot-swap operation capability.
-
Product
COM Express Type 6 Development Kit
COM Express Type 6 Starter Kit Plus
Computer on Module
The Type 6 Starter Kit Plus consists of a COM Express Type 6 module with ATX size Type 6 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for DDI adapter card that convert DDI signal to DP or HDMI signal, one PCI Express graphics x16 slot, one PCI Express x4 slot, three PCI Express x1 slots, Serial ATA, VGA, LVDS, USB3.0/2.0, Gigabit LAN and Super I/O. All necessary cables are included.
-
Product
PCI Express card carrier, PCIe Gen 3 x8 connection
SA4-COUNTRY
-
The SA4-COUNTRY is a peripheral slot board for PICMG® CompactPCI® Serial systems and acts as carrier for low profile PCI Express® Card. The SA4-COUNTRY is provided with a PCI Express® x8 connector.
-
Product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
Remote Control Interface
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
Product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
