Prototyping
Construction of first working designs.
-
Product
PXI Prototyping Module, 2-Slot, 50-Pin D-Type
40-225A-502
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Prototyping Adapters/Interposers
-
Prototyping adapters breakout from any package type to 2.54mm pitch pins or a larger pitch SMT footprint to solder to your development board. Our extensive design library means that many are available for fast delivery or next day from RS Components.
-
Product
Prototyping Service
-
Not sure if your new idea is going to work? Come and talk to us. We have a lot of experience in developing proof-of-concept benchtop systems. Remember, it’s not a “lash-up”, it’s the “first step in your product development cycle”. The picture shows a prototype double-pass spectrometer (on the left) that was built into a portable, robust benchtop unit (on the right).
-
Product
PXI Prototyping Module, 1-Slot no Connector
40-225A-001
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Rapid Prototyping and Manufacturing
-
We work closely with you in the early in the life cycle of your product development. Our extensive knowledge of the latest innovative prototyping tools enables us to design and produce initial designs quickly and to specification. Once the prototype has been tested and the design accepted, we are able to provide full small scale manufacturing options to bridge the gap to full outsourced manufacturing.
-
Product
Prototyping Kit
VXI-5502
-
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, 96-Pin Micro-D
40-225A-102
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
HEVC Analyzer for Rapid Prototyping
HARP
-
HARP is an open source toolkit for rapid prototyping of new HEVC / H.265 video codec extensions. Our motivation for creating HARP lies in the simple idea that a well-chosen development environment allows to focus time and resources more on the design stage of new HEVC extensions and less on subsequent implementation and debugging tasks.
-
Product
PXI Prototyping Module, 1-Slot, 50-Pin D-Type
40-225A-501
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-802
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 37-Pin D-Type
40-225A-201
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 15-Pin D-Type
40-225A-601
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Rapid Prototyping
-
Prototyping is a crucial step in the larger product design and development process. Prototypes allow organizations to stress-test their ideas, evaluate form factor and appearance, assess feasibility and production requirements, and ultimately produce a solid proof of concept. But prototyping can be a surprisingly challenging undertaking: it requires sourcing different materials and parts, possibly incorporating mechanical engineering alongside industrial design, and combining skillsets to produce a single, tangible prototype.
-
Product
TySOM Embedded Prototyping Boards
-
TySOM™ is a family of embedded system prototyping boards. Depending on the board, one of three FPGAs will be at its heart: a Xilinx Zynq® UltraScale+™, a Xilinx Xilinx Zynq-7000 or a Microchip PolarFire SoC. The boards are compatible, through industry standard interfaces (FMC or BPX), with Aldec’s wide range daughter cards, making Aldec’s TySOM embedded prototyping boards ideal for the rapid development of applications that include automotive (and ADAS, in particular), artificial intelligence (AI), machine learning (ML), embedded vision, embedded-HPC (including edge-processing), IoT, IIoT and industrial automation.
-
Product
PXI Prototyping Module, 2-Slot, 25-Pin D-Type
40-225A-302
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Custom Solutions
-
We employ a collaborative process that provides our customers with the perfect component. This step-by-step process guides our customers through the creation of totally customized products. Our expert sales engineers take you from conceptual design to prototype, and then final part production, making the process as easy as possible.
-
Product
Patterning Simulation
-
KLA’s patterning simulation systems use advanced models to explore critical-feature designs, manufacturability and process-limited yield of proposed lithography and patterning technologies. Our patterning simulation software allows researchers to evaluate advanced patterning technologies, such as EUV lithography and multiple patterning techniques, without the time and expense of printing hundreds of test wafers using experimental materials and prototype process equipment.
-
Product
FlexRay Interface Device
FlexRay Interface
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PXI Breadboard Module, 2-Slot, 15-Pin D-Type
40-220A-602
Signal Module
Versatile PXI Breadboard with 65 sq cm (10 sq in) of Prototype Area, fitted with 15-pin D-type connector, dual PXI slot width.
-
Product
PCI Express Ultra-fast Data Acquisition Add-In Cards
-
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
Product
Prototype Performance Field Testing iOS app
-
Centric's new Field Testing app provides an innovative solution for product performance feedback. Centric's Field Testing App is an example of how capturing data live, in the moment, is not only incredibly valuable but also a natural way of working. This app helps reducing costs while also improving product innovation and performance; which are ultimately keystones of great brands.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785167-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Evaluation and prototyping application
-
Intuitive graphical user interfaceCall and immediately display the result of any Open eVision functionGenerate C++, C# and Visual Basic codeFree of charge
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
Data And Telecommunication
-
Imec is an ideal partner to help you remain on top. We are developing solutions taking into account long-term industry roadmaps. You will profit from our collaborations with the largest players in the ecosystem. Moreover, as the emerging technologies involve new materials and components, we also offer capacity for integration, prototyping, small-to-medium volume production and – through our partners – even large volume manufacturing.
-
Product
R&D Testing
-
In today's rapidly changing global economy, constant revision and development of the product range is necessary for business growth. To efficiently bring safe, reliable, and high-quality products to market, testing of materials and prototypes is critical.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785161-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PLD Systems
Pulsed Laser Deposition
-
Is a versatile thin film deposition technique. A pulsed laser (~20 ns pulse width) rapidly evaporates a target material forming a thin film that retains target composition. This unique ability of stoichiometeric transfer of target composition into the film was realized first by the research team led by Dr. Venkatesan at Bell Communications Research, NJ, USA, nearly 30 years ago while depositing high temperature superconducting (YBa2Cu3O7) thin films. Since then, PLD has become the preferred deposition technique where ever thin films of complex material compositions are considered. Another unique feature of PLD is its ability for rapid prototyping of materials. The energy source (pulsed laser) being outside the deposition chamber, facilitates a large dynamic range of operating pressures (10-10 Torr to 500 Torr) during material synthesis. By controlling the deposition pressure and substrate temperature and using relatively small target sizes, a variety of atomically controlled nano-structures and interfaces can be prepared with unique functionalities.
-
Product
Interference Lithography Gratings
-
Interference lithography is an optical nanolithography technology for the fabrication of extensive periodic nanostructures. Critical dimensions of less than 50 nm can be realized. At AMO two interference lithography tools are installed. One setup for extensive, high quality gratings with fixed periods, the other more flexible tool allows quick prototyping. We offer grating fabrication on silicon, silicon dioxide and other substrates with tailored pitch, etch depth and size.
