Distributed Antenna System
-
Product
Antenna, Active Loop
EM-6869 | 9 KHz – 50 MHz
-
The Electro-Metrics EM-6869 Active Loop Antenna is used with any receiver or spectrum analyzer with 50 ohm input and covers the frequency range of 9 kHz to 50 MHz.
-
Product
Antenna
-
Beijing KeHuan Century EMC Technology Co,.LTD
Antenna is adjusted using the receiver, use, testing, measurement, etc.
-
Product
Mezzanine System
5147
System
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
Product
Antenna, Active Loop
EM-6876 | 9 KHz – 30 MHz
-
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
Product
Switched Power Distribution Module, CAN Control
H730008KS
-
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
Mezzanine System
5235
System
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
Product
Standard Gain Horn Antennas
-
Linear polarized Broadband Horn Antenna (Brass with Plastic mounting body) for Receive and Transmit Applications.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Antennas
-
A specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
Product
Active broadband antenna up to 6GHz
Series HyperLOG ® 70 X
-
Compatible with any Spectrum Analyzer or Oscilloscope. Incl. High-End Preamplifier. Ultra high gain (44dBi). The HyperLOG X LogPer antenna series can be used to locate extremely weak signals, thanks to the integrated preamplifier. The antenna offers excellent directional characteristics which can be optimized using theoptional Laser and Compass.
-
Product
Active Antenna Combiner
M2C
-
The M2C active antenna combiner is designed as an ideal matching component to Lectrosonics digital transmitters. Up to eight transmitters can feed a single antenna to minimize cabling in multi-channel systems. The inputs are isolated to minimize crosstalk and IM (intermodulation) between RF channels.
-
Product
Monitoring & Drive Test Antennas
-
Linear polarized half-wave dipole with 1:1 balun and fixed element length for fieldstrength measurements at TETRA (terrestrical trunked radio) networks.
-
Product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
-
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Product
Antenna, Log Periodic
EM-6950 | 200 MHz – 1 GHz
-
The Electro-Metrics EM-6950 Log Periodic Antenna was designed to operate over the 200 MHz to 1 GHz frequency range to meet VDE/FCC, military, and other EMI specifications.
-
Product
H-Field Rod Antenna
-
The A.H. Systems' set of H-Field Rods provide an accurate standard for magnetic field testing. The rods are available individually or in a set of four to cover the frequency range of 100 Hz to 30 MHz.
-
Product
Antenna, Log Periodic
EM-6944 | 200 MHz – 3 GHz
-
The EM-6944 offers an exceptional combination of frequency coverage from 200 MHz – 3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
VHF/UHF Handheld Signal Location Antennas
Type NVF-2
-
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
Product
Systems
-
Walter Stauffenberg GmbH & Co. KG
Custom-design and ready-to-install hydraulic pipe, tube and hose assemblies from port to port
-
Product
Bi-Sector Array Antennas
-
*Dual 33 degree beam antennas with a 65 degree pattern foot print*Multi-band capable*IIndependent tilt control for each beam**RemoteElectricalTilt (AISG 2.0)*Increase site capacity & data throughput
-
Product
Distributed 4-Axis Motion Control Modules (with High-Speed Trigger Function)
MNET-4XMO-(C)
Motion Controller
The MNET-4XMO is a 4-axis motion controller module for Motionnet distributed motion systems. It can generate fast frequency pulses (9.9 MHz) to drive stepper or servomotors in the machine automation field. As a motion controller, it can provide comprehensive motion functions which include 2 axis circular interpolation, 2-4 axis linear interpolation, or continuous interpolation for continual velocity and so on. Also, changing position/speed on the fly is available with a single axis operation.
-
Product
Mezzanine System
5188
System
ECM P/N 5188 provides an AD8109 crosspoint switch for analog or digital signals with 250MHz of Bandwidth. For single ended applications 8 inputs can be connected up to 8 outputs in any configuration.
-
Product
Broadband Antenna
OBDR
-
Broad frequency range, ideal for complementing RF test enclosures in various test setups
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Edge AI Inference System
AIR-020R
Edge AI Inference System
Edge AI Inference system powered by NVIDIA® Jetson Orin™ Nano and Super mode. Compact and performance AI box design. NVIDIA® Jetson Orin™ Nano 8GB/4GB built-in.
-
Product
Dual Polarized Broadband Horn Antennas
-
Linear polarized dual double ridged broadband antenna for receive and transmit applications made of aluminium.
-
Product
ANTENNA ANALYZER
MFJ-213
-
MFJ-213 covers 1-60 MHz with digital precision. It also displays SWR, complex impedance, and impedance magnitude simultaneously all on the same easy-to-read LCD screen.
-
Product
Base Station Antennas
-
This antenna provides Omni-Directional platform for advanced use in encompassing low band deployment scenarios and AWS and PCS in high band in a high quality package design built to withstand harsh environments.
-
Product
CB Antennas
-
Recommended by virtually every equipment manufacturer for their proven and time-tested technical compliance, Shakespeare CB antennas deliver value and quality.
-
Product
Enclosed Fanless Industrial Embedded Computer with NXP® i.MX8M Application Processor
SYS-444Q
Computer System
The SYS-444Q is a rugged enclosed fanless embedded computer system with NXP’s i.MX8M industrial application processor with quad-core Arm Cortex®-A53 for low-power processing. This rugged system has dual Ethernet, industrial I/O, expansion options, TPM 2.0 hardware security, and options for wireless connectivity. The processor supports industry-leading video processing along with an M4 microcontroller for real-time subsystems making it an ideal fit for industrial IoT applications requiring highly reliable performance in harsh conditions such as digital signage, industrial automation, energy management, building automation, and others.
