Print Circuit Board
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
Burn-In Board Tester
Focus-275
-
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
Product
Boards
MIL-STD-1760
-
The MIL-STD-1760 interface card is compatible with all common variations of MIL-STD-1760 and provides a wide range of features normally found only on full size testers. The cards can operate simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection.
-
Product
6-24V Heavy Duty Circuit Tester
1654
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 24V systems.
-
Product
PC/104 OneBank Board
EMC2-ZU3EG
-
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU3EG is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU3EG is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
Product
SparkFun SAMD21 Development Board
Qwiic Micro
-
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
Product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP VZ
-
Materials and Finishes MATERIAL: Heat treated beryllium copper and music wireFINISH: 24 Kt gold plate over hard electroless nickel
-
Product
High-Low Circuit Tester
29500
-
The low-side checks AC and DC current up to 28 volts with power on. The high-side checks spark plug wires without piercing. Complete with insulated clip.
-
Product
Embedded Transceivers
-
Embedded transceivers are chip-sized components based on 850 nm VCSELs and offer bandwidth up to 300 Gbps for short reach applications (<300 m). These transceivers can be soldered or socketed to a printed circuit board and are well suited for small, compact systems requiring high I/O density, low power, and small space. Many of these transceivers have been qualified to operate in harsh environments, such as the ones found in space, and aerospace and defense applications.
-
Product
Hall Sensor Board with I2C Interface
046-322
-
Version: +5V/15A +12V/5A -5V/15A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Virtex 5 Based PXIe Board.
SMT700
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PCI Express To CPCI Board
MS 1719
-
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
-
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Product
Data Acquisition Processor Board
DAP 5000a
-
When your application needs Pentium-powered real-time processing under Windows, choose the DAP 5000a. Even at maximum sampling rates, the combination of a fast processor with low latency allows computation in real time between samples – and on-time response for control applications.
-
Product
ARM LPC2364 Board
MS 1541
-
- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit
-
Product
3.5" Single Board Computer With Intel® X7835RE/x7433RE/x7211RE Processor
SBC35-ASL
Single Board Computer
The SBC35-ASL is a versatile and high-performance 3.5" single board computer, designed to meet the demands of industrial and outdoor applications. Powered by Intel® x7835RE/x7433RE/x7211RE processors and supporting up to 16GB of DDR5 4800MHz memory, it delivers robust performance for real-time processing needs. Its triple display outputs, including eDP/LVDS, HDMI, and DP, make it ideal for graphics-intensive tasks, while dual Gigabit Ethernet ports ensure reliable connectivity. Built for extreme environments, the SBC35-ASL operates within a temperature range of -40°C to 85°C, ensuring durability in harsh conditions.
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
Termination Board
MSTB 009
-
The MSTB 009 a-Series Analog Termination Board allows quick and secure connection of discrete wires to Data Acquisition Processors. It is the only analog termination board that may be used with the DAPs listed at the bottom of this page.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Heavy Duty Circuit Tester / Jumper
32900
-
Heavy-duty circuit tester for checking low voltage up to 12 volts. By depressing the red button the tester becomes a jumper for powering electrical components or a ground. The probe, handle, cord and clamp are reinforced for durability. Comes with a strain relief spring on the cord.
-
Product
Embedded Single Board Computers
-
Advantech Embedded Single Board Computer (SBC) series include: 2.5" Pico-ITX, 3.5" PC/104, 5.25" EBX, and MI/O Extension form factors. They offer scalable x86 performance from low power to high-end, and from fanless and slim, to extended temperature platforms with longevity. They are ideal for system integration with high flexibility and expansion possibilities, and compact sizes with rich I/O. Reliability was built in for highly reliable 24/7 operation and industrial grade rugged operation.
-
Product
3.5" Single Board Computer
RSB-4710
Single Board Computer
RSB-4710 is a RISC 3.5" single board computer (SBC) powered by a high-performance Rockchip RK3399 ARM dual Cortex-A72 and quad Cortex-A53 high performance processor which supports 4K display from HDMI. It offers both multiple display as dual HDMI/LVDS/eDP and multiple IO as dual GbE/6 x serials/6 x USB/5 x GPIO. RSB-4710 also features Mini-PCIe, M.2, and SIM card slots for integrating Wi-Fi, Bluetooth, and 3G/4G modules. It is an ideal solution for Kiosk, POS, and Vending machine application.
-
Product
PCIExpress Kintex UltraScale FPGA Carrier Board
PCU: 085/115
-
The PCU continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD Kintex UltraScale FPGA computing power. The PCU is a PCIExpress, standard form factor , FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications at a competitive price point. AMD Kintex UltraScale XCKU085/115 delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PCU FPGA node processes input from the FMC HPC +(Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 12.0GSPS).
-
Product
SparkFun MicroMod WiFi Function Board
ESP32
-
The SparkFun MicroMod ESP32 Function Board adds additional wireless options to MicroMod Processor Boards that do not have that capability. This special function board acts as a coprocessor that takes advantage of Espressif's ESP32 WROOM to add WiFi and Bluetooth® to your applications.
-
Product
Compact 3U CPCI Processor Board
CP32110
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Atom™ x5/x7 E3900 series (Apollo Lake-I), Pentium® N4200 and Celeron® N3350 CPU, CP32110 is a compact 3U CPCI single board computer compliant with CompactPCI® specification.On CP32110, there is a Mini SATA interface for system software installation, and several peripheral interfaces include SATAII, USB2.0 and Giga bit Ethernet.
-
Product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
-
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
SparkFun MicroMod Machine Learning Carrier Board
-
The MicroMod Machine Learning Carrier Board combines some of the features of our SparkFun Edge Board and SparkFun Artemis boards, but allows you the freedom to explore with any processor in the MicroMod lineup without the need for a central computer or web connection. Voice recognition, always-on voice commands, gesture, or image recognition are possible with TensorFlow applications. The cloud is impressively powerful but all-the-time connection requires power and connectivity that may not be available. Edge computing handles discrete tasks such as determining if someone said "yes" and responds accordingly. The audio analysis is done on the MicroMod combination rather than on the web. This dramatically reduces costs and complexity while limiting potential data privacy leaks.
-
Product
Data Acquisition Board
DAP 4200a
-
The DAP 4200a is an excellent choice for applications where there is a need for real-time processing of data in the time interval between samples, and for applications requiring fast sample rates. Much of the DAP 4200a design is similar to that of the DAP 3200a/415, but the DAP 4200a has a PCI host interface, and is capable of high speed data transfers to the host PC.
-
Product
Form A Circuit Board 80 Channel, 300 VDC, 2 A
OTP2 module no.195
-
The 40-139 2A relay series is suitable for applications requiring medium power, high density switching. With a current capacity of 2 A and voltages up to 300 VDC / 250 VAC, it is suitable for cost-critical applications.
-
Product
Stationary Circuit Breaker Testing
ACTAS L260
-
High-precision test system for function tests on various types of switchgear device, including circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit.The inputs and outputs are connected flexibly via a terminal strip, making the test system particularly suitable for use in development and laboratory environments as well as in production environments.
