Firmware
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
Software Defined Radio Firmware
FWSDR
-
The combination of the firmware FWSDR and the high-end digitizer ADQ14 creates a unique platform for software-defined radio. This 14-bit digitizer provides the high dynamic range needed in an RF environment and the interleaving technology provides high signal bandwidth coverage.The interleaving technology is provided through the use of SP Devices’ proprietary technology ADX which removes typical interleaving artifacts and enables the unique combination of bandwidth and dynamic range.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10R
-
OP-FW10R is a firmware to expand the measurement speed for bit synchronous communication such as HDLC/SDLC/X.25, CC-Link and SPI communication up to 10Mbps. Processing major part of the measurement process by FPGA, it enables capturing of communication data with time stamp of micro-second unit.
-
Product
Real-Time Pulse Detection Firmware
FWPD
-
The core challenge in pulse detection is to design a system for random events. The Teledyne SP Devices’s firmware option FWPD, for the ADQ14 and ADQ7, is tailored to detected and analyze pulses in demanding measurement applications where the properties of the pulses (such as timing or length) are not known in advance.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
Product
Digital Down-Conversion Firmware
FW2DDC
-
FW2DDC equips ADQ7WB and ADQ7DC with real-time functions commonly used in radio frequency (RF) receivers. It also contains the proprietary ADX technology which corrects mismatch errors in time-interleaved analog-to-digital converters (TI-ADCs) and thereby ensure industry-leading spurious-free dynamic range (SFDR). The digital signal processing also helps reduce the data rate to a manageable level in order to simplify data post-processing and storage.
-
Product
Software / Firmware
-
You can connect to our Ethernet test box right now and send/receive remote commands. It is located at fixed IP address 104.63.176.50 (tcp port 3001). The most often asked question about our test systems is “How easy are they to remotely control”? So we built up a test system and put it on an outward-facing IP address so that any of our customers can interact with our firmware.
-
Product
Firmware for High-speed HDLC/SPI Communications (NEW Version)
OP-FW12G
-
This expansion firmware increases the baud rates of bit synchronous communications (e.g., HDLC/SDLC/X.25, and CC-Link communications). The firmware processes main measurement items completely with a field programmable gate array (FPGA), thus precisely capturing communications data along with time stamps in 1-µs units.
-
Product
Real-Time Waveform Averaging Firmware
FWATD
-
The Advanced Time-Domain firmware option, FWATD, equips the ADQ7 and ADQ14 digitizers with advanced tools for sophisticated time-domain measurements. Multiple steps of noise suppression is provided in order to achieve extreme dynamic range, so that rarely occurring weak signals can be detected and distinguished from noise.FWATD can track and correct for temperature-dependent baseline (DC level) fluctuations, which may otherwise lead to incorrect detection or even detection of false pulses. It supports several types of noise reduction for both random and systematic noise. The flexible architecture and user-defined settings enables tailored noise reduction for various applications.
-
Product
Portable Sequence Generator for Verification, Firmware & Validation
ISequenceSpec
-
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
Product
ADQ Development Kit for Custom Firmware in the FPGA of an ADQ-Series Digitizer
-
The ADQ Development Kit is a tool for developing custom firmware in the FPGA of an ADQ-series digitizer. SP Devices’ digitizers are characterized by a combination of high speed and high resolution.The amount of data from the digitizer is thus very high. The most efficient way of processing the data is through a real-time implementation inside the FPGA on the digitizer. The ADQ Development Kit opens the FPGA for the implementation of real-time signal processing algorithms.The ADQ Development Kit is available for all digitizer models.
-
Product
VPX Power Supplies
-
Dawn is the leader in VITA 62 compliant power supplies for the mission critical market. Wide range of standard features, highly configurable through custom firmware.
-
Product
15.6" Full HD, 512MB, 8GB (EMMC), Seria Lx3, Dual Ethernet
WOP-315K
-
ARM9™ Cortex-A35 800MHz + 8GB for fast, smooth performance500+ protocols – connect any device, cut integration costs16MB non-volatile memory protects data from power lossFree HMINavi Designer – Serial/Ethernet/USB, no license neededUnlimited I/O/macros, up to 7,999 screensNo limitation on the internal I/Os points used for variety applicationReliable firmware setting from HMINavi software for 24/7 operationEasy to switch one application to different LCD sizes in secondsIP65 aluminum – tough and stylish
-
Product
Network Analyzer N-Port Calibrated Measurements
S95551B
Network Analyzer
PXI vector network analyzers (VNA) offer the capability to extend the number of ports for your measurements by using additional modules. When multiple modules are used, they are configured for multiport operation. The S95551B adds a multiport analyzer mode that enables full multiport error correction and measurement capabilities. The instruments may be identified as one VNA by the firmware running on an external host PC. At least one VNA instrument connected to your PC must have one S95551B license to maintain N-port capabilities.
-
Product
Electronic Compass - 3-axis Solid-State Magnetometer, 2-axis Electrolitic Tilt Sensor
Revolution
-
The Revolution electronic compass combines a precision 3-axis solid-state magnetometer and a rugged 2-axis electrolytic tilt sensor to provide accurate heading and tilt measurements over a broad range of environmental conditions. The firmware and signal processing algorithms have been refined and improved over three prior generations of electronic compasses to deliver the ultimate in performance from the available sensor data.
-
Product
Digital Signal Processing
ITA
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
Product
Custom And ODM Designs
-
Added intelligence in the form of custom firmware, FPGA design and microcontroller code add product feature for differentiation in the market.
-
Product
AXIe High-Speed Digitizer/Wideband Digital Receiver, 12-bit, 3.2 GS/s, 8-ch, FPGA Signal Processing
M9703B
Digitizer
Based on the AXIe standard the M9703B is an 8-channel, 12-bit digitizer/wideband digital receiver, able to capture signals from DC up to 2 GHz at 1.6 GS/s. A channel interleaving capability allows waveform acquisition at up to 3.2 GS/s with exceptional measurement accuracy. The M9703B also provides real-time data processing, large FPGA and customizable I/O interfaces. Detailed explanations can be found in the firmware options section of the datasheet.
-
Product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Signal Averaging eXpert FPGA DSP Feature for CompuScope Digitizers
Digitizer
Utilizing the eXpert Signal Averaging Firmware on a GaGe CompuScope Digitizer allows users to detect a small repetitive signal in a noisy environment by conducting rapid signal averaging completely on the digitizer's onboard FPGA with absolutely no host system CPU loading.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
Handover Test Systems
-
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
Product
GPIB To Serial Miniboxes™
-
ICS's GPIB to Serial Minibox™ Interfaces are fully enclosed for benchtop or rack mount applications. The GPIB to Serial Interfaces are available for transparent data transfer and with smart firmware to add an IEEE-488.2 interface to any serial device
-
Product
Toolbox.NET
Software for Data Exchange
-
The Toolbox .NET provides firmware upgrade capabilities and data transfer stored in internal instrument memory to a PC. The Toolbox .NET is based on Microsoft .NET Framework 3.5 and will operate with the following Raytech products:
-
Product
ColorFlex EZ Coffee Spectrophotometer
Spectrometer
Hunter Associates Laboratory, Inc.
The easy-to-use ColorFlex EZ Coffee is specifically built to meet and exceed your needs in measuring the color of roasted coffee grounds. It makes it easy to define the degree of roasting. Coffee color scales provided in firmware include: HunterLab Coffee Color Index (HCCI), SCAA Number & SCAA Roast Classification.
-
Product
AMI Meter Farms
-
Do you have new AMI meters going into the field? Or have you already deployed your new meters, but will have firmware upgrades soon? Allow us to introduce the TESCO Meter Farm, our newest offering to support your AMI Meter Deployment. The Meter Farm powers up banks of meters and runs a current load through each meter. TESCO Meter Farms are designed to serve as a cost effective method for testing communication, functionality and firmware upgrades from your meter manufacturer(s). The Meter Farm can be used as part of the qualification process prior to deployment, but has been more popular as a post deployment tool to allow large scale testing of all new releases of firmware over hundreds or even thousands of meter points prior to upgrading the entire system. The Meter Farm can also be used to perform long term testing for new hardware releases prior to introducing later generation meters into the field. As with all of our products, the TESCO Meter Farm is built with the tradition of reliability and ruggedness.
-
Product
PCIe Gen 4 Switch Adapter
P411W-32P
-
The Broadcom P411W-32P is the industry’s first fully managed Gen 4.0 NVMe switch adapter, providing enterprise class options for NVMe solid state drive (SSD) attach requirements. The P411W-32P leverages Broadcom’s world-class board design, PEX88048 PCIe Gen 4.0 switch chip, and solid firmware expertise, to provide advanced features not available using traditional NVMe drive attach methods. Similar to Broadcom HBAs, the P411W-32P adapter is supplied with fully validated and supported firmware and standards based out of band manageability features.
