Wave form
-
Product
Rotating Ring Disk Electrode
RRDE-3A
-
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
-
Product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
-
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
Product
Telecom Test Systems
4301 Series
-
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
Product
Pulse Tesla Meter
GP-300
-
Pulse field intensity can be read directly. Wave form is observed by oscilloscope. Measuring range:0.01T~9.99T .
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
1000 Amp AC True RMS Digital Clamp Meter
DL6403
-
True RMS reading on AC current and AC voltages provide accurate measurement regardless of the wave form, which makes this the ideal instrument for commercial and industrial applications where no linear loads are present.
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Digital Surge Tester
KT-905D
-
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
Product
Databus-to-Network Interfaces
OBB2
-
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
-
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
Product
PXIe Avionics Interface Cards
-
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
Oscillators for Radio Amateurs
-
An oscillator is an electronic circuit designed to produce either audio or radio frequency signals. These will generally have sineusoidal wave form, but other wave shapes such as square and sawtooth are possible. In radio equipment oscillators will always have a low output power, and if a radio frequency is produced, the oscillator is acually a basic radio transmitter.
-
Product
1000 Amp AC/DC True RMS Digital Clamp Meter
DL6404
-
The top of the range DL6404 provides True RMS reading on AC current and AC voltages allowing accurate measurement regardless of the wave form. This makes it the ideal instrument for commercial and industrial applications where non linear loads are present.
-
Product
Signa; Generator
MAG-203AD
-
Features:*Signal frequency:0 .1Hz-2Mhz, continuously variable*Wave form: square,sine*Output attenuator:0dB, 20dB, 40dB,60dB*Output level: 20Vp-p in open circuit, not less than 10Vp-p with 50Ω load*Rising and falling edge of square not more than 35ns*Sine distortion less than 1%,amplitude -frequency characterstic:±0.3dB within 100khz, ±1dB above 1Mhz*Frequency meter: 10Hz-30Mhz*Power supply : AC 220V
-
Product
Magneto-Electric Rotation Detector
MP-981/AP-981
-
The MP-981 is a magneto-type detector using a hall element which is suitable for revolution (r/min) measurement from low speed to high speed.Magneto-type detectors use an internal hall element, a permanent magnet, DC amplifier, and voltage regulator and respond to flux, so that a rectangular wave form is derivable from much lower speed all the way though high speed.In addition, a signal indicator is provided in spite of the detector's compact design, making verification of operation and mounting position possible.Meanwhile, the AP-981 is the water and acid proof type, which conforms to Class ' of JIS C0920.
-
Product
Signal Generator
MAG-2015AD
-
Feature:*Signal frequency: 0.1Hz~15MHz, continued*Wave form: square,sine*Output attenuator: 0dB,20dB,40dB,60dB*Output level: 20Vp-p in open ciruit,not less than 10Vp-p with 50Ω load*Rising edge of Square not more than 35ns at 2MHz*Sine distortion less than 1%,amplitude-frequency characteristic ±0.5dB with in 2MHz, ±3dB above 10MHz*Frequency Counter: 20Hz~30MHz*Power supply: AC 220v (110v optional)
-
Product
Wave Buoy
MOTUS
-
The MOTUS (movement in Latin) Wave Buoy is a perfect solution for collecting environmental data in coastal areas.Collect reliable environmental data with MOTUS Wave Data Buoy.The MOTUS (movement in Latin) Buoy is a perfect solution for collecting environmental data in coastal areas for all-year deployments. The platform used for collecting data is a robust buoy which has proven to be an excellent platform for providing high accuracy and reliable meteorological and oceanographic data. The wave buoy can effectively combine various Hydrological and Meteorological parameters. Basic parameters such as wind, waves, and currents can easily be expanded to include sensor packages with different water quality sensors. Data is controlled and synchronized by the data management systems that Xylem Analytics offers, which also controls and powers real-time communication. This provides a low-power efficient system offering long-term deployment capabilities.The MOTUS Wave Buoys combine our ultra-low power and field-proven solutions from developing oceanographic and water quality sensors. We have 60 years of experience operating in the industry, providing you with an optimal platform based on the buoy, a rugged, lightweight polyethylene buoy deployed in more than 40 countries all over the world. By selecting Xylem as your partner in your projects, you are on track for the lowest overall cost of ownership and a versatile platform that can be tailored to your needs. The MOTUS Buoy is developed for both scientific and commercial use.
-
Product
Acoustic Wave Device
-
Murata offers high-performance acoustic wave radio frequency (RF) devices including filters, duplexers, diplexers, resonators, and frequency control devices. This allows us to provide a wide range of acoustic wave-based RF devices in a one-stop service to all RF engineers.
-
Product
Guided Wave Radar
-
A top-down, direct sensing technology that uses low-energy microwave pulses sent down a probe to accurately detect the boundary between two immiscible liquids.
-
Product
3D Form Measurement
-
Ensure that components function and can be fitted correctly with efficient form monitoring. ISRA’s 3D form measurement systems capture component geometries down to the nanometer level while ensuring the shortest cycle times.
-
Product
Workhorse Waves Array
-
Teledyne Marine RD Instruments
Workhorse Waves Array is an innovative, cost-effective upgrade that allows you to take your Teledyne RDI ADCP to the next level. Via a simple upgrade, you can capture not only the industry’s most field-proven and dependable precision current profiling data, but highly accurate multi-directional wave measurements as well.
-
Product
Wave Soldering Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
Product
Wave display utility
GUI
-
GUI allowing users to view and analyze test vectors in all common formats (VCD/EVCD/WGL/STIL).
-
Product
Shear Wave Transducers
-
At Precision Acoustics, we manufacture normal incidence shear wave probes at 1 MHz, which can be coupled directly to an object through a shear wave coupling gel.
-
Product
Mm Wave Measurement
Erickson PM5B
-
bsw TestSystems & Consulting AG
Erickson PM5B from VDI, which has been further optimised in the version just presented. The measuring head of the PM5B operates in the WR10 band, i.e. in the 75 - 110 GHz range. High-precision accessories, so-called tapers, provide for adjustments and thus make measurements in the waveguide bands, currently up to WR0.34 beyond 3 THz, possible.
-
-
Product
Traveling Wave Tube Amplifier
-
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
Product
RF Detectors for Millimeter Wave
-
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
Product
Surface Form Analysis System
Tropel® FlatMaster®
-
Tropel® FlatMaster® Surface Form Analysis System Fast and Precise Measurements of Ground, Lapped, Honed, Polished and Super-finished Components. The Tropel® FlatMaster® offers industry leading performance for surface form measurements to precision component manufacturers. Our non-contact optical technique analyzes the entire surface of the part in seconds, regardless of its size or complexity. The FlatMaster provides five nanometer resolution and a standard accuracy of 50 nm (2.0 μ). It rapidly and accurately measures flatness, line profile, radius and other surface parameters on a variety of materials and surface finishes.
-
Product
Rugged, Small Form Factor Networking Systems
-
Curtiss-Wright Defense Solutions
Our field-proven, rugged switches and routers enable mobile networks on-board vehicle and aircraft platforms to securely and affordably deploy digital network architectures for situational awareness and network-centric operations.
