Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
Pre- Locator
CFL PL2+
-
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
Product
Travelling Wave Fault Location Test Kit
PH Series
-
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
Product
K-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-K001
-
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Mating Coax Connector With 20 Coax Pins Crimped (One End) To 5 Foot Wires
GX96404-60
-
Mating Coax Connector with 20 Coax Pins crimped (one end) to 5' wires. Coaxial cable: RG316, 50 ohms.
-
Product
4 Wire Earth Resistance & Resistivity Tester
4236 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.● Optical USB to RS-232 data transmission.● The stored data can be transferred to a PC.● 2 optical LEDs are built-in for data transfer.
-
Product
Rebar Locator
Profoscope +
-
The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection. Writing down measuring results of testing series is a time consuming business that can be an unnecessary source of errors. The various data storage modes of the rebar locator Profoscope+ make note taking obsolete. This cordless rebar detector is ideally suited for one-handed operations, keeping the other hand free for marking rebars.
-
Product
L60+ Thermocouple & Fine Wire Welder
-
The Thermocouple Welder, manufactured by Labfacility, is a compact, simple-to-use instrument designed for thermocouple and fine wire welding.
-
Product
Tool, Locator, Thermocouple, ITA
910104135
Locator Tool
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
Product
ACR ResQLink View 425 PLB (Personal Locator Beacon)
2922
-
Small but resilient, the self buoyant (floating) ResQLink View has been professionally engineered and tested to ensure it can withstand even the harshest elements. This buoyant Personal Locator Beacon requires no subscription for use and includes a digital display providing live status and GPS coordinates. Whether on land, at sea, or in the air, trust that the ResQLink’s satellite precision and military durability, puts rescue in the palm of your hands.
-
Product
160-Pin DIN Female To 6-Pin Bare Wire Male Switch Cable
782417-01
Switch Cable
160 Pin DIN to Bare Wire Cable for PXI Switches, 1m
-
Product
Locate and Map Underground Utilities
UtilityScan DF
-
Geophysical Survey Systems, Inc.
UtilityScan DF incorporates our innovative dual-frequency digital antenna (300 and 800 MHz) and an easy-to-use touchscreen interface to view shallow and deep targets simultaneously in a single scan.
-
Product
Fault Locator
REZAP FAULTMASTER
-
REZAP FAULTMASTER is an auto-recloser that keeps customers on supply during intermittent faults.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
PXI Pull-Thru Adapter, Wired, Micro Coaxial, 18 MCX Plugs and 2 SMB Plugs
510140119
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, Micro Coaxial, 18 MCX Plugs and 2 SMB Plugs
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
510140251
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
-
Product
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
510140129
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
-
Product
Visual Fault Locator
TM191
-
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
Product
68-Pin VHDCI Female to 68-Pin Bare Wire Male Multifunction Cable
189041-02
Multifunction Cable
SHC68-NT-S Shielded Cable for 7831R boards, 68-pin VHDCI to unterminated, 2m
-
Product
Receiver, G18, 18 Module For Discrete Wiring
310120101
Receiver
The lightweight and rugged 18 module Receiver provides a solution that will accommodate larger ATE chassis’ (PXI, VXI, SCXI). It allows immense versatility by affording space for up to an 18 slot PXI chassis.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
12-600V AC Adjustable Non-Contact Wire Tracer
5221
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
Cable Fault Location Equipment
-
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
Product
Wire Tracer
-
*Detect through the shielded cable*Instantaneous finding of AC current*Tracing cables*Monitoring current status in applicances*Compares the AC current*Tracing cables inside the wall*Locating underground cables*Detects magnetic field*Low voltage high current detection
-
Product
Power Cable Fault Locator
TM500
-
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
Product
68-Pin DIN-Rail SCSI Wiring Board
ADAM-3968
-
DIN-rail mounting screw terminal module for industrial applications with 68-pin SCSI female connectoCase dimensions (W x L x H): 77.5 x 191.2 x 51 mm (3.1" x 8.4" x 2.0")To Be Used With PCI-1710U/UL/1710HGU/1711U/UL,PCI-1712/L,PCI -1716/L,PCI-1741U/1742U/1747U/1780U
-
Product
Thermocouple & Fine Wire Welder
L60
-
The Thermocouple Welder, manufactured by Labfacility, is a compact, simple-to-use instrument designed for thermocouple and fine wire welding.
-
Product
Fault Locating
-
Schweitzer Engineering Laboratories, Inc.
The built-in fault-locating methods in SEL devices allow you to quickly identify faults, dispatch crews for repairs, and restore service faster. Traveling-wave fault-locating technology calculates the locations of temporary and permanent faults by measuring the arrival times of the naturally occurring traveling waves caused by a transmission line fault. Accurately detecting these waves requires ultra-high-resolution monitoring, and locating is accurate to within one tower span (±300 m). Impedance-based fault-locating technology calculates fault locations by detecting changes in line impedance as a result of a fault. Impedance-based locating is reliable and accurate to about 2 percent of a line’s total length.
-
Product
Location Devices
-
Flash Pinger is a small battery powered acoustic transmitter as well as an optical flashing recovery device. Multiple settings allow for selection of flashing, timing, and frequency options for use in a variety of different applications.
-
Product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
