RF Amplifiers
take low power RF signals and output RF signals that vary in the same way as the input signal, but with a raised amplitude.
See Also: Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers, Microwave Amplifiers, Rf Power Amplifiers
-
Product
HF Amplifier
-
bsw TestSystems & Consulting AG
Whether a HF amplifier which is mounted in a 19" rack is viewed as an instrument, a system or a component largely depends on the point of view of the application developer. We list this product family here; however we would like to point out that our 19" amplifiers for rack-mount and benchtop applications, as well as modules without power supply, are listed in the "Components" section.
-
Product
RF Adapters
TNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series TNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance TNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm TNC connectors have a frequency range from DC to 11 GHz. 75-ohm TNC connectors have a maximum frequency of 3 GHz.
-
Product
Class A Amplifiers
-
An audio power amplifier design where the output transistors constantly conduct electrical current through the entire 360-degree cycle of an input signal.
-
Product
Single Channel High Voltage Linear Amplifier
A800
-
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
3-5 Watt Power Amplifiers
CCM1095 and CCM2096
-
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
High-Power Pulsed Amplifiers
-
High power pulsed amplifiers are capable of providing over 1KW of peak power above 10GHz. These SWaP-optimized, high-reliability products have been designed to withstand the toughest environments. For custom requirements, Mercury leverages its proven building-block design approach to rapidly deliver a solid-state power amplifier (SSPA) for your application.
-
Product
Hybrid Amplifiers
Gain Block
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components thindat include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
RF Tracking Generators
-
Using a Spectrum Analyzer (SA) in combination with a Tracking Generator (TG) enables swept scalar frequency response measurements of active and passive networks.
-
Product
Intelligent RF Spectrum Recorder
ODEN 3001
-
ODEN 3001 is the first intelligent RF spectrum recorder within Novator Solutions wideband record and playback offering with 26.5GHz frequency range and 765MHz real-time bandwidth. ODEN 3001 automatically captures individual interfering signals or rare & unknown events of interest for later analysis and spectrum characterization.
-
Product
Variable Gain Optical Amplifier Module
VGA4700-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4700-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
High Performance/Software Controllable RF Multicouplers
-
1U High Performance Rack Mount Broadband Multicouplers, with configurations up to 1×8 or switchable 2×4 configurations. Features include High Output/Output Isolation and Software Controllable power level and amplitude balance.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
System Amplifier
SAM100
-
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Adapters
SMA Adapters
-
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
Product
Lock-in Amplifier
UHFLI
-
The Zurich Instruments UHFLI is a digital lock-in amplifier covering the frequency range from DC to 600 MHz. In addition of providing the highest operation frequency amongst all commercial lock-in amplifiers, the UHFLI also offers the lowest time constant of 30 ns for demodulation, resulting in a demodulation bandwidth of more than 5 MHz. The exquisite analog front end offers a spectacular noise performance of 4 nV/Hz which helps in many applications to keep the signal-to-noise ratios high while speeding up the measurement. In combination with the most innovative instrument control software LabOne, the UHFLI is the flagship of all Zurich Instruments products and represents the state of the art of today''s scientific instrumentation.
-
Product
RF Capture & Player
-
This device can record RF signals in various points of fields. When reproducing the signal data infactories or laboratories, it is possible to test receivers under the reception environment of the data.
-
Product
UltraCMOS SP6T RF Switch
PE42562
-
The PE42562 is a HaRP™ technology-enhanced absorptive SP6T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42562 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
Product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
-
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
Product
GHZ-Wideband Amplifiers
-
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
RF & Microwave Connectors, Adapters And Cables
-
SHF Communication Technologies AG
RF adapters, microwave cable assemblies and high frequency connectors up to 110 GHz can be supplied by SHF. Our partners KMCO and Totoku are located in Japan and provide excellent product quality, competitive pricing and fast delivery.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
CATV & RF Signal Products
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
-
Product
Pulsed Injection-Locked IMPATT Amplifiers
Pulsed ESR/EPR
-
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
RF Waveguide Load
-
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
Product
RF Subsystems
-
Using the Ideal Switch to develop RF subsystems enables substantial performance and reliability improvements. At the same time their size and weight decrease by several orders of magnitude.
