Traffic Simulators
simulate communications over a network.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
VDT/Resolver Simulation Module for SLSC
Simulator
Bloomy's VDT/Resolver Simulation Module offers eight channels of variable differential transformer (VDT) sensor simulation at an unmatched price point. Its highly-flexible nature allows each channel to be configured independently for simulation of a linear variable differential transformer (LVDT), a rotary variable differential transformer (RVDT), or a resolver. Versatile, separate E1 and E2 returns allow each channel to be connected in a 4-, 5- or 6-wire configuration. The included VeriStand SLSC driver also allows each channel to simulate two 4-wire sensors where shared excitation is acceptable.
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
Simulator
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-911
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
Simulator
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 750 V Isolation
43-752A-013
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
41-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PCIe
APE-FDX-2/B
Simulator
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI Millivolt Thermocouple Simulators
Series 41-760
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-912
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI RTD Simulator Module, 16 Channel, PT1000
40-263-203
Simulator
The 40-263-203 is a 16-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Analog Output/Thermocouple Simulator - 32 Channel, ±100mV
41-761A-001
Thermocouple Simulator
The 41-761A-001 is a 32-channel low voltage output module ideal for simulating the operation of a thermocouple. It is part of a range of modules available with a choice of 32, 24, 16 or 8 channels. Each channel provides a low voltage output across two connector pins capable of providing ±20 mV with 0.7 μV resolution, ±50 mV with 1.7 μV resolution and ±100 mV with 3.3 μV resolution, covering most thermocouple types. For applications that require slightly higher voltages, there are also options that provide up to 250 mV, 500 mV, 1000 mV, 1500 mV and 2000 mV.
-
Product
PXI RTD Simulator Module, 20 Channel, PT500
40-263-102
Simulator
The 40-263-102 is a 20-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Synchro/Resolver Simulator, Programmable
5330A
Simulator
NAI's 5330A Synchro/Resolver Simulator is a rack-mount or bench-top instrument featuring integrated touch-screen controls and input terminals. This model represents a major step forward as it uses digital technology to produce Synchro and Resolver outputs. Improved flexibility is provided by two fully independent outputs that can be used to simulate two separate Synchro or Resolver signals simultaneously, or can be combined to operate as two-speed outputs. The versatility of this device has been substantially increased by incorporating dynamic modes that enable servo systems to be tested under various simulated stringent field conditions.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 3k
50-265-104
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Portable Range Threat Simulators
Simulator
The Textron System's PRTS™ and HPRTS™ are medium and long-range, programmable, ruggedized Radio Frequency (RF) test and training tools. Our PRTS family of range simulators delivers high-fidelity environments for training ranges.
-
Product
Photovoltaic Array Simulator
PV8900 Series
Simulator
Keysight’s photovoltaic (PV) simulator includes the hardware and software to test a single maximum power point tracking (MPPT) inverter accurately. Test PV voltages up to 2000 V and 60 A with a single supply. DG9000 Series software licenses are available to test string inverter with 4-, 8-, or 12-MPPT channels. Most string inverter solutions test one MPPT channel at a time — leading to test inaccuracies. Keysight's DG9000 advanced PV inverter software can test up to 12 MPPT channels simultaneously.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
43-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1K
40-265-202
Strain Gauge Simulator
The 40-265 is a strain gauge simulator that simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
43-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
