Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
W Series Panel Meter
ST-475
-
Standard Electric Works Co., Ltd
● Measuring Range : DC uA-200, 500 DC mA -1, 5, 10,15, 20, 30, 50, 100, 150, 300, 500 DC A -1, 5, 10 DC V -5, 10,15, 20, 30, 50, 100, 150, 300, 500● Accuracy : Class 2.0● Case and Composition: Acrylic Resin front and ABS Resin case Bezel mounting● Color：Black case, yellow scale plate.● Pointer：Tube type, black or red LED Custom ranges depend upon warrant quantity Suitable for VU meters of Amplifier usage
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
-
Product
Microwave Power Amplifier 1/2 Watt 100 MHz to 20 GHz
GT-1020A
-
The Spanawave/Giga-tronics GT-1020A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
-
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
Product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - 6U VPX
Model 57664
-
- Supports Xilinx Virtex-6 LXT and SXT FPGAs- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Variable Gain Amplifier
VGA
-
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
Product
Broadband High Power Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's broadband high power amplifiers are available for operating frequencies from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 2 watts to over 500 watts. Based on state-of-the-art GaN, GaAs, LDMOS power devices and MMICs, KeyLink designs and manufactures SSPA(solid state power amplifiers ) with excellent performance in terms of high efficiency over ultra-wide working band, high reliability and ruggedness.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
Product
100mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Precision Op Amplifiers (Vos <1mV & TCVos<2uV/C)
-
Analog Devices' broad range of precision amplifiers provides industry-leading support to designers in need of traditional trimmed and zero-drift amplifier technology. Our precision amplifier family helps preserve the accuracy of dc information in an incoming signal with low offset voltage (VOS < 1 mV) and low temperature drift characteristics (TCVOS < 2 V/C).
-
Product
Amplifier Dyno
AD-1
-
The AD-1 Amplifier Dyno is a tool that is designed to be used any place an amplifier exists. It can be used in a lab or production line to test true amplifier power output, quickly and easily. It is simple menu driven, does not require a computer, and cannot be cheated as the load banks are internal. It can be used in an automotive audio install shop to test true amplifier output while the amplifier is installed in the customer's vehicle.
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
Amplifiers
-
CAES manufactures custom amplifiers in a wide variety of configurations from LNA (Low Noise Amplifiers), Medium and High Power, and wideband solutions.
-
Product
Amplifier Gain Blocks
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a wide portfolio of Amplifier Gain Blocks for RF, microwave, and millimeter wave applications. Our amplifier gain blocks cover frequencies ranging from DC to 45 GHz. MACOM’s gain blocks are used in a variety of 50 Ohm and 75 Ohm applications including; Networks, Commercial and Aerospace and Defense. Leveraging the latest innovative technology these products are available in both standard plastic packaging and bare die.
-
Product
Dual Channel High Voltage Linear Amplifier
F1020
-
This unit contains two independent amplifiers that share common ground reference and power supply. Left channel correspond to the F10A model and right channle corresponds to the F20A model.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
Product
Narrow Band LNA Family
-
The COMM-connect range of Narrow Band Low Noise Amplifiers can be used to amplify signals in a very wide range of bands. The amplifiers comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
W Series Panel Meter
ST-315
-
Standard Electric Works Co., Ltd
● Measuring Range : DC uA-200, 500 DC A -1, 5, 10 DC V -5, 10,15, 20, 30, 50, 100, 150, 300, 500● Accuracy : Class 2.0● Case and Composition: Acrylic Resin front and ABS Resin case Bezel mounting● Color：Black case, yellow scale plate.● Pointer：Tube type, black or red LED Custom ranges depend upon warrant quantity Suitable for VU meters of Amplifier usage
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - 6U VPX
Model 58661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 57851
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
